• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.718-724
• /
• 2018

In this study, the $Ni_{0.9}Co_{0.05}Ti_{0.05}(OH)_2$ precursor was prepared by the concentration gradient co-precipitation method. In order to overcome the structural change due to oxygen desorption in the cathode active material with high nickel content, the physical and electrochemical analysis of the cathode active material according to the calcination temperature were investigated. Physical properties of $Li_{1.05}Ni_{0.9}Co_{0.05}Ti_{0.05}O_2$ were analyzed by FE-SEM, XRD and TGA. The electrochemical performance of the coin cell using a cathode active material and $LiPF_6$(EC:EMC=1:2 vol%) electrolyte was evaluated by the initial charge/discharge efficiency, cycle retention, and rate capabilities. As a result, the initial capacity and initial efficiency of cathode materials were excellent with 244.5~247.9 mAh/g and 84.2~85.8% at the calcination temperature range of $750{\sim}760^{\circ}C$. Also, the capacity retention exhibited high stability of 97.8~99.1% after 50cycles.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.2
• /
• pp.82-87
• /
• 2005

The cathode material, $LiNi_{0.5}Mn_{1.5}O_4$, for high voltage applications of Li-ion batteries exhibits impurity phases due to oxygen deficiency during the high temperature heat treatment. The impurity phase reduces the electrochemical properties of the electrode since the deficiency spinel structure disturbs the lithium ion intercalation and deintercalation. In this study, Cr-substituted $LiNi_{0.5-x}Mn_{1.5}Cr_xO_4(0{\leq}x{\leq}0.05)$ powders are synthesized by a sol-gel method in order to reduce the amount of the impurity phases in the $LiNi_{0.5-x}Mn_{1.5}Cr_xO_4$. Thermal analysis of the cathode material shows that the $LiNi_{0.5}Mn_{1.5}O_4$ without Cr substitution looses $2\%$ of its weight due to oxygen deficiency but the amount of weight loss is diminished when Cr is substituted. XRD analysis also supports the reduction of the impurity phases in the cathode after chromium substitution, suggesting that the improvement of the electrochemical properties such as the capacity retention and electrochemical stability are attributed to the low content of impurity phases in the Cr-substituted $LiNi_{0.5-x}Mn_{1.5}Cr_xO_4.$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.259-259
• /
• 2007

층상구조의 전이금속 산화물($LiMO_2$, M=Co, Ni, Mn)은 리튬이차전지용 양극재료로 활발한 연구가 진행되고 있다. 차세대 리튬이차전지 시스템의 개발 및 고성능화를 위해서는 전지의 용량을 결정하는 핵심 부품인 양극재료의 고용량화 및 고안정화는 필수 불가결하다. 따라서 본 연구에서는 상업적으로 큰 장점이 있는 고상반응 공정을 이용하여 리튬이차전지용 양극소재를 제조하고, 소재의 전기화학적, 구조적인 특성을 평가하였으며, 다음과 같은 주제를 가지고 연구를 진행하였다. $LiCoO_2$ 양극재료는 리튬이온전지로 널리 사용되고 있다. 높은 에너지 밀도의 리튬이온전지를 얻기 위해서는 $LiCoO_2$ 양극재료가 고용량화 및 고밀도화를 가져야 한다. 여기서 $LiCoO_2$ 분말이 irregular particle morphology를 가지면 tap density가 $2.2-2.4gcm^{-3}$로 에너지 밀도가 낮으나, 구형 $LiCoO_2$의 정극재료는 tap density가 $2.6-2.8gcm^{-3}$로 상대적으로 energy density가 높아지는 효과가 있다. 구형 $LiCoO_2$ 양극재료를 합성하기 위해서는 chelating agent를 이용한 "controlled crystallization" 침전법을 사용하여 합성한 구형 코발트 수화물을 사용하고 있다. "controlled crystallization" 침전법에서 사용되는 chelating agent로는 주로 ammonia가 이용되고 있다. 본 연구에서는 chelating agent로 ethylene diamine을 사용하여 sodium hydroxides를 precipitation으로 침전 반응하여 구형 코발트 수화물을 합성하였다. 상기 방법으로 합성된 코발트 수화물과 리튬 수화물($LiOH{\cdot}H_2O$-고순도화학(高殉道化學))을 사용하여 고상법을 통하여 $LiCoO_2$를 합성하였다. 제조된 분말의 결정구조와 전기화학적 특성분석은 X-선 회절분석 및 리트벨트 구조정산, 그리고 충/방전 싸이클링을 수행하였으며, 분말의 미세구조 변화를 SEM을 이용하여 분석하였다.

• Membrane Journal
• /
• v.20 no.3
• /
• pp.259-266
• /
• 2010

Porous poly(propylene) supported gel polymer electrolytes (GPE) were synthesized by thermal polymerization of DEGDMA [Di(ethylene glycol) dimethacrylate] in electrolyte solutions (1 M solution of $LiPF_6$ in EC/DEC 1 : 1 mixture) at $70^{\circ}C$. AC impedance spectroscopy and cyclic voltammetry were used to evaluate its ionic conductivity and electrochemical stability window of the GPE membranes. Lithium ion battery (LIB) cells were also fabricated with $LiNi_{0.8}Co_{0.2}O_2$/graphite and GPE membranes via thermal polymerization process. Through the thermal polymerization, self sustaining GPE membranes with sufficient ionic conductivities (over $10^{-3}\;S/cm$) and electrochemical stabilities. The LIB cell with 5% monomer showed the best rate-capability and cycleability.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.593-598
• /
• 2011

The IPA-co-HDO-co-(TPA/MA) copolymers for all-vanadium redox flow battery were synthesized by melt condensation polymerization using isophthalic acid(IPA), 1,6-hexandiol (HDO), terephthalic acid(TPA) and maleic anhydride(MA). The amination of chloromethylated IPA-co- HDO-co-(TPA/MA)(CIHTM) copolymer was carried out using trimethylamine, and the anion exchange membrane was also prepared by UV crosslinking reaction. The structure and thermal stability of IHTM copolymers were confirmed by FTIR, $^1H$ NMR, and TGA analysis. The anion membrane properties such as water uptake, ion exchange capacity, electric resistance and electrical conductivity, were measured by gravimetry, titration and LCR meter. The efficiency of the all-vanadium redox flow battery was analyzed. The ion exchange capacity, electric resistance and electrical conductivity were 1.10 meq/g, $1.98{\Omega}{\cdot}cm^2$, and 0.009 S/cm, respectively. The efficiency of charge-discharge, voltage, and energy for the allvanadium redox flow battery were 96.5, 74.6, 70.0%, respectively.

• Elastomers and Composites
• /
• v.39 no.3
• /
• pp.179-185
• /
• 2004

Frequency dependency or electrical property stabilization during vulcanization of modified NR/IR composite materials was studied using in-situ electrical property measuring technique. Volume resistivity(p) before and after vulcanization reaction of the sample was measured as the function or frequency in the range or 1Hz to 10kHz at reaction temperatures of 130, 140, 150, and $160^{\circ}C$, respectively. A double stabilization mode of frequency dependency was observed, in which a slow stabilization process of p to a value of ca. $1.0{\times}10^7\;{\Omega}-cm$ occurred after a drastic initial decrease from ca. $9.0{\times}10^7\;{\Omega}-cm$. In addition, notable temperature dependencies of p values were also observed before and after vulcanization reaction, that is, p values at 130 and $140^{\circ}C$ after vulcanization were observed as about 1/3 of those values before vulcanization. All the observed facts were considered as the results from the interaction between the electrode and the bulk sample materials, i.e., electronic charge-discharge, and from the structure change of samples including CB rearrangement by the vulcanization.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.832-840
• /
• 2019

To improve the electrochemical performances of the cathode materials, boron-doped $LiNi_{0.90}Co_{0.05}Ti_{0.05}O_2$ were synthesized by using concentration gradient precursor. The characteristics of the prepared cathode materials were analyzed by XRD, SEM, EDS, PSA, ICP-OES and electrical conductivity measurement. The electrochemical performances were investigated by initial charge/discharge capacity, cycle stability, C-rate, cyclic voltammetry and electrochemical impedance spectroscopy. The cathode material with 0.5 mol% boron exhibited a capacity of 187 mAh/g (0.5 C) in a voltage range of 2.7~4.3 V(vs. $Li/Li^+$), and an capacity retention of 94.7% after 50 cycles. In the relatively high voltage range of 2.7~4.5 V(vs. $Li/Li^+$), it showed a high capacity of 200 mAh/g and capacity retention of 80.5% after 50 cycles.

• Clean Technology
• /
• v.27 no.3
• /
• pp.223-231
• /
• 2021

In order to address many issues associated with large volume changes of silicon, which has very low electrical conductivity but offers about 10 times higher theoretical capacity than graphite (Gr), a silicon nanoparticles/hollow carbon (SiNP/HC) composite having bimodal-mesopores was prepared using silica nanoparticles as a template. A control SiNP/C composite without a hollow structure was also prepared for comparison. The physico-chemical and electrochemical properties of SiNP/HC were analyzed by X-ray diffractometry, X-ray photoelectron spectroscopy, nitrogen adsorption/desorption measurements for surface area and pore size distribution, scanning electron microscopy, transmission electron microscopy, galvanostatic cycling, and cyclic voltammetry tests to compare them with those of the SiNP/C composite. The SiNP/HC composite showed significantly better cycle life and efficiency than the SiNP/C, with minimal increase in electrode thickness after long cycles. A hybrid composite, SiNP/HC@Gr, prepared by physical mixing of the SiNP/HC and Gr at a 50:50 weight ratio, exhibited even better cycle life and efficiency than the SiNP/HC at low capacity. Thus, silicon/carbon composites designed to have hollow spaces capable of accommodating volume expansion were found to be highly effective for long cycle life of silicon-based composites. However, further study is required to improve the low initial coulombic efficiency of SiNP/HC and SiNP/HC@Gr, which is possibly because of their high surface area causing excessive electrolyte decomposition for the formation of solid-electrolyte-interface layers.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.759-764
• /
• 2018

3D porous carbon electrodes (cNPIM), prepared by solution casting of a polymer of intrinsic microporosity (PIM-1) followed by nonsolvent-induced phase separation (NIPS) and carbonization are presented. In order to effectively control the pore size of 3D porous carbon structures, cNPIM was prepared by varying the THF ratio of mixed solvents. The SEM analysis revealed that cNPIMs have a unique 3D macroporous structure having a gradient pore structure, which is expected to grant a smooth and easy ion transfer capability as an electrode material. In addition, the cNPIMs presented a very large specific surface area ($2,101.1m^2/g$) with a narrow micropore size distribution (0.75 nm). Consequently, the cNPIM exhibits a high specific capacitance (304.8 F/g) and superior rate capability of 77% in an aqueous electrolyte. We believe that our approach can provide a variety of new 3D porous carbon materials for the application to an electrochemical energy storage.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1088-1095
• /
• 2018

In this study, reduced graphene oxide/polyaniline composite was fabricated tomaximize their advantages with electrochemical performances and use as a electrodematerial for supercapcaitor. Polyaniline as an electrode material was synthesized bychemical polymerization of aniline monomer and reduced graphene oxide wasintroduced to prepare composite with polyaniline without any pre-treatment. Thereduced graphene oxide, polyaniline and their composite electrodes were fabricatedon gold coated PET(polyethylene terephthalate) substrate through spray coatingmethod which can also apply to industrial scale. we have also prepared reducedgraphene oxide and polyaniline single material electrode to compare theirelectrochemical properties with reduced graphene oxide/polyaniline composite electrode. We have analyzed and compared electrochemical properties of eachelectrodes by using cyclic voltammetry(CV), galvanostaticcharge-discharge(GCD) and electrochemical impedancespectroscopy(EIS) at same condition. As a result, reduced graphene oxide /polyaniline composite electrode showed higher capacitance value more thanpolyaniline and reduced graphene oxide electrode, respectively. Internal resistanceof reduce graphene oxide/polyaniline composite electrode was 24% and 58% lessthan polaniline and reduced graphene oxide electrode respectively. These resultsconsidered that reduced graphene oxide/polyaniline composite electrode has potential ability and enable to apply flexible energy storage and wearable devices.