• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.10
• /
• pp.873-882
• /
• 2009

Sonolysis of TCE (Trichloroethylene) was performed in 584 kHz rectangular reactor. At first, the effect of acoustic power and aqueous temperature which are both important factors to operate ultrasound system on sonolysis of TCE were examined under one side irradiation condition. First degradation rate constants of TCE and chloride yields were increased with increasing acoustic power from 100 to 300 W. And increasing the aqeuous temperature resulted in the increase of first degradation rate constants of TCE and the decrease of chloride yield. Sonolysis of TCE was performed under multi ultrasound irradiation conditions that total acoustic power of 300 W was distributed according to the number of irradiation sides. First degradation rate constants of TCE followed the order 4 sides > 3 sides > 1 side > 2 sides (parallel) > 2 sides (orthogonal). When comparing the experimental results under parallel and orthogonal irradiation conditions of 2 sides with 300 and 450 W, first degradation rate constants of TCE were similar, while production rate constants of hydrogen peroxide were more higher at parallel conditions compared to orthogonal conditions.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.4
• /
• pp.15-20
• /
• 1975

The power overshoot is rises in the output during the transient period when the output of nuclear reactor is increased from the initial state to the desired target state and certain amount of constraint on power level is of primary importance for safety control of nuclear reactor. Therefore, the maximum principle is applied to this process control in transfering its power from the initial state(no, co) to the final target state(2no, 2co or 1.5no, 1.5co), adjusting the reactivity so that its overshoot is limited within the allowable constraint required. In this case, the switching points, switching times, optimal lima and optimal control reactivity are calculated.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.123-127
• /
• 2021

Millimeter-wave tracking radars should be operated in various environmental restrictions, thus they demand more computing power and smaller size compared to conventional tracking radars. This paper presents the design and implementation of the compact power supply for millimeter-wave tracking radar applications. To meet requirements of low voltage/high current and voltage accuracy for FPGA/DSP digital circuits, Point of Load (POL) converters are used in order to enhance power density and system efficiency. LDO (Low Dropout) is applied for the output voltage under the light load condition, then the single-input-multi-output power supply with max power of 375 W and 8 outputs is developed. The proposed power supply achieves output voltage accuracy of ±2 % and noise level of <50 mVpp % under full load conditions.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.11
• /
• pp.861-869
• /
• 1989

The optimization problems, based on Pontryagin's Maximum Principle, for minimizing (damping) Xenon spatial oscillations in Load Following operations of Pressurized Water Reactor (PWR) is presented. The optimization model is formulated as an optimal tracking problem with quadratic objective functional. The oen-group diffusion equations and Xe-I dynamic equations are defined as equality constraints. By applying the maximum principle, the original problem is decomposed into a single time problem with no constraints. The resultant subproblems are optimized by using the conjugate Gradient Method. The computational results show that the Xenon spatial oscillation is minimized, and the reactor follows the load demand of the electrical power systems while maintaining the desired power distribution.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.5
• /
• pp.99-103
• /
• 2022

Millimeter-wave tracking radars operate in various environmental restrictions, thus they demand stable power sources with low noise level under high fluctuation of input voltage. This paper presents the design and implementation of the compact power supply with max power of 727 W for Ka-band tracking radar applications. To meet requirements of voltage accuracy and system efficiency for transceiver circuits, upper plates of buck converters are attached on the covers of power supply for efficient heat dissipation. The proposed power supply achieves system efficiency of 88.4 %, output voltage accuracy of ±2 % and noise level of <1% under full load conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.474-482
• /
• 1999

In this paper, a new field weakening algorithm which maximizes the output torque not only in steady state b but also in transient state is proposed. Considering both voltage and current limit of system, analytic solutions f for optimal torque utilization in field weakening region I and region II are obtained. This algorithm finds optimal currents considering dynamic vol떠ge limit based on flux and speed. So the maximum usage of stator v voltage even in transient state results in the maximum torque and fast response time. Simulation and e experimental results show the effectiveness of the proposed field weakening scheme.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.938-940
• /
• 2003

고출력 반도체 레이저(500mW)의 출력광 파장 809nm과 반도체 레이저로 여기되는 Nd:YVO4레이저의 출력광 파장 1064nm를 공진기 내부에서 비선형 광학 소자인 KTP(Potassium titanyl posphate : KTPiOPO$_4$)를 사용하여 합주파 발생 실험을 행하여 459nm의 청색레이저를 얻었다. 제2의 위상 정합 정합조건($\psi$=90$^{\circ}$, $\theta$=90$^{\circ}$)에서 반도체 레이저의 입력광 세기가 400mW일 때 청색레이저의 최대 출력 0.95mW를 얻었으며, 청색레이저의 발진문턱입력 세기는 120mW이었다.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2010.07a
• /
• pp.417-419
• /
• 2010

본 논문에서는 최적화 문제를 해결하는 기법의 하나인 유전자 알고리즘을 이용하여 모든 노드를 탐색하여 최적의 경로를 도출하는 최적화 경로 탐색 알고리즘을 제안한다. 경로를 도출하기 위해 중간 경로 노드로부터 출발지 노드 및 도착지 노드까지의 거리를 측정하여 개체를 생성한다. 출력 노드들을 도출하기 위해 생성된 개체를 적합도 함수에 적용하여 적합도를 계산한다. 계산된 적합도 값에 따라 교배를 할 노드 및 교배 지점(비트단위)을 선택한다. 선택되어진 교배와 교배 지점을 이용하여 개체들을 교배한다. 교배를 통해 새로운 개체를 생성한다. 새로운 개체가 적합도 조건(이전 개체 중 최대값 $^*\;2$)에 만족한다면 출력 노드로 도출하고, 다음 출력 노드를 도출할 때의 출발지 노드로 선택되어진다. 이러한 과정을 반복하여 모든 출력 노드를 도출한다. 제안된 방법을 실험한 결과, 순차 방식과 난수를 이용한 경우보다 제안된 방법이 효율적인 것을 확인하였다.

• ICROS
• /
• v.17 no.4
• /
• pp.46-50
• /
• 2011

다변수 입출력 제어시스템에서 제어기를 설계하기 위해서는 단일 입출력 시스템에서와 마찬가지로 저주파수영역에서는 루프전달행렬의 크기가 작은 것이 요구되고, 측정잡음 및 플랜트의 불확실성이 존재하는 고주파수 영역에서는 루프전달행렬의 크기가 작게 되도록하여, 잡음의 영향이 출력에 적게 나타나고, 제어기가 포화되지 않도록 하며, 설계된 제어기가 플랜트 모델의 불확실성을 극복할 수 있게 하는 것이 필요하다. 본 원고에서는 각 전달 행렬들의 특이치의 최대 및 최소값들을 이용하여 다변수 제어기가 갖추어야 할 조건들을 정리하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.971-974
• /
• 1987

Considering heat transfer and heat loss processes for the heat engine operating between two fixed heat reservoirs, it may be qualitatively explained that the maxima of power output and its efficiency depending upon operating conditions are extreme maxima. Furthermore, it is also found that from an economic point of view the above two extremes are related to extreme minima of plant cost per unit power output and operation cost per unit power output respectively, and the condition of minimum cost per unit power output exists between the extreme minimum conditions of plant cost per unit power output and that of operation cost per unit power output.