• Resources Recycling
• /
• v.28 no.6
• /
• pp.54-63
• /
• 2019

This study investigated on the compressive strength and the length change test with using the waste glass and graphene oxide for recycling the waste glass as the aggregate. Curing on 3-day and 7-day, the compressive strength was enhanced as the usage of waste glass was increased. Especially, the huge difference in the compressive strength was observed when the amount of substituting on the waste glass was used on 10~50%. With 50% of waste glass condition, the compressive strength was portionally enhanced as the usage of graphene oxide was increased and its value was 42.6 N/㎟ with 0.2% of graphene oxide. In terms of the length change test, the use of high content of waste glass led length change value to increase, but it was dropped down as the portion of waste glass was above 50%. Furthermore, in the case of using 50% of waste glass, the use of high amount of graphene oxide tended to decrease the length change value. That is, graphene oxide may contribute on boosting the cement hydration reaction and blocking the ion's movement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1095-1104
• /
• 2014

This paper presents the results of experimental work on both strength characteristics and durability of concrete or mortar having 50% ground granulate blastfurnace slag(GBS) with different fineness levels (4,450, 6,000 and $8,000cm^2/g$). Compressive and split tensile strength test results indicated that the concrete with a higher fineness level of GBS exhibited a better strength development due to the acceleration of latent hydraulic property at the later curing stage compared with ordinary portland cement concrete. Meanwhile, it was found that a higher fineness level of GBS showed some negative effects on the resistance against freezing-thawing action. However, incorporation of GBS to concrete, irrespective of fineness levels, significantly enhanced the chloride ions penetration resistance. The resistance against sulfate attack of mortar with GBS was greatly dependent on the attacking sources from sulfate environments.

• Journal of the Korean Society for Railway
• /
• v.17 no.5
• /
• pp.365-372
• /
• 2014

Technologies for rapid concrete curing using elevated temperature are important for saving cost and time when constricting concrete structures. Recently, a microwave heating form was developed. In this study the early strength of concrete cured by the developed form was experimentally investigated. Large scale mock up tests were conducted six times, and the results were analyzed based on the maturity theory. Logarithmic correlation curves were generated based on the measured strength and estimated maturity. It was confirmed that the strength development of the concrete cured by microwave heating form can be estimated by the equivalent age theory usually applied to steam-curing technology. By using the microwave heating form, one day at most is enough to get the required strength for the safe removal of forms, even in cold weather.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.218-225
• /
• 2023

In this study, we examine the feasibility of using chlorine in clinker as an early-strength cement by the effect of accelerating the cement hydration reaction of chlorine. Clinker with a chlorine content of 200-1,000 ppm was prepared using actual cement kilns, and 46 cement samples were prepared by adding gypsum and admixtures(GGBFs and limestone). We measured consistency, setting, 1-28 days compressive strength and analyzed them statistically. Test results indicated that an increase of the chlorine content resulted in shortening of initial and final setting time and the improvement of 1 day compressive strength. But the 28 days compressive strength was decreased. Specifically, when the chlorine content was increased from 230 to 965 ppm, the 1 day compressive strength increased up to 4.6 MPa, improvement effect was superior to that of increasing Blaine in the range of 3,400-3,970 cm²/g.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.135-144
• /
• 1997

표면 활성효과에 대한 비정질 규소 박막의 고성결정화 특성을 연구하였다. 증착된 비정질 규소 박막에 macro한 방법으로 wet blasting을, micro한 방법으로 자기이온주입으로 표면 활성화 처리를 행한 후 열처리를 하여 결정립의 결정화 특성을 보았다. 열처리는 관상로를 이용한 저온 열처리와 RTP를 이용한 급속 열처리의 두 가지 방법으로 하였다. 결정화의 기준으로 XRD분석을 통해 얻은 (111) 피크 강도를 이용하였으며, 결정의 품질을 비교하기 위해 Raman 분석을 하였다. 기계적 damage를 이용한 표면 활성화는 결정화를 촉진함을 확인하였으며 활성화 방법에 따른 결정화 영향 변화정도는 열처리 온도가 증가함에 따라 감소하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.10a
• /
• pp.260-263
• /
• 1998

섬유단면이 원형이 아닌 L, T, H, W, Y, I 등과 같은 모양을 가지는 이형단면 섬유(shaped fiber)는 그 모양으로 인해 원형단면 섬유와는 다른 광택, 마찰계수, 촉감, 굽힘강도 등을 가지고 여러 가지 용도로 쓰이고 있다. 이형단면 섬유의 용융방사시 같은 면적을 가진 원형단면 섬유와 비교해 증가된 표면적은 열과 물질 전달을 증가시키고 고화를 촉진한다. (중략)

• Magazine of the Korea Concrete Institute
• /
• v.4 no.2
• /
• pp.75-81
• /
• 1992

염분을 함유한 철근콘크리트중의 철근부식에 관한 2년 촉진시험으로부터 콘크리트표면에서 측정한 자연전위값과 실제의 철근 부식상황과를 비교한 결과 철근의 수식상황을 자연전위법을 이용하여 비파괴적으로 진단하는 방법이 유효함을 알았다. 포화칼로멜전극을 사용했을 경우 -300mV이하이면 부식이 발생하였으며 -200mV이상이면 부식이 발생하지 않았다. 또한 부시공시체에 대한 휨강도시험도 행하였으며 중성화에 대한 검토로 행하였다.

• Applied Chemistry for Engineering
• /
• v.5 no.1
• /
• pp.63-73
• /
• 1994

Weight loss accelerating agents, TDACW and TTAMW were prepared by adding water to n-tetradecyldimethylbenzylammonium chloride(TDAC) and n-tetradecyltrimethylammonium methyl sulfate(TTAM) synthesized in our lab. On weight loss finishing of PET fiber with NaOH and TDACW or TTAMW, TDACW showed much more weight loss than TTAMW. Optimum concentration was about $8g/{\ell}$, treatment time 60~90min and treatment bath ratio 1:40~1:50. Density and crystallinity increased with weight loss and tensile strength decreased with weight loss. From the reaction mechanism of weight loss accelerating agent and PET fiber, weight loss accelerating agent was proved to function as a catalyst and the surface structures of PET fibers treated with weight loss accelerating agent were characterized with SEM.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.235-244
• /
• 2012

A thiazole type accelerator MBT (2-mercapto benzothiazole) was added into silica filled natural rubber (NR) compound with various concentrations (0, 1, 2, 3, 4 phr). The effects of MBT on the cure rate, mechanical property, degree of rubber-filler interaction (${\alpha}_F$), crosslinking density, and viscoelastic property ($tan{\delta}$) were investigated. As accelerator concentration increased, the $t_{s2}$ and $t_{90}$ decreased and the crosslinking density and modulus at 300% elongation increased. The tensile strength and elongation increased up to 3 phr and no further increased at 4 phr. The $tan{\delta}$ value measured at room temperature was higher than that of the $70^{\circ}C$. The ${\alpha}_F$ value was not affected by the addition of MBT. The mechanisms for the vulcanization rate were reviewed.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.943-947
• /
• 2002

In order to examine the possibility of incineration of inderstrial by-product and wastes which contains a large percentage of chlorine by the cement kiln, measured heat of hydration, setting time, flow, change of length, compressive strength of OPC by the amount of KCl. The result was that a shorter setting time, a lower flow, a increasing the degree of initial shrinkage, a increasing of compressive strength before 3 days and decrease after 7 days by the induction period is shorter as promote the hydration with KCl.