• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.214-222
• /
• 2001

A precise echosounding system to investigate the topographical characteristics of the coastal fishing ground was composed of a public-DGPS receiver, a single beam echosounder and a survey software. To confirm the usefulness of the system, a set-net fishing ground and the distribution of artificial reefs were surveyed. The results obtained are as follows : 1. The 2-D positioning error of the public-DGPS receiver with a DGPS mode and a GPS mode was 5.47 m, 7.03 m, respectively. 2. The experimented set-net fishing ground was located on the level ground at the depth of 9-10 m, a small size valley 1-2 m deep and approximately 10 m wide was found at a distance of 120 m from the set-net to the south. 3. In the artificial reefs' water area near the Jaran Bay, it was confirmed that twenty rectangular artificial reefs were established by the piece at the depth of 15-25 m and a natural reef 5-8 m high on the sea bed was located near the group of artificial reefs. 4. It was confirmed that the precise echosounding system was a useful tool in the pre-study to choice an appropriate water area to provide the artificial reef.

• Journal of the Korean Chemical Society
• /
• v.50 no.3
• /
• pp.208-215
• /
• 2006

A simply prepared graphite, pencil-type working electrode was utilized to monitor fenitrothion concentrations, using the cyclic voltammetry (CV) and square-wave (SW) stripping voltammetry methods. The optimum conditions for analysis were sought. A very low detection limit was obtained compared to that obtained when other common voltammetry methods are used. The optimal parameters of the pencil-type electrode were found to be as follows: a pH of 3.7, a frequency of 500 Hz, an SW amplitude of 0.1 V, an increment potential of 0.005 V, an initial potential of -0.9V, and a deposition time of 500 sec. The analytical detection limit was determined to be 6.0 ngL-1 (2.16410-11 molL-1) fenitrothion at SW anodic and CV, and the relative standard deviation at the fenitrothion concentration of SW anodic 10 ugL-1 was 0.30% (n = 15) under the optimum conditions. Analysis was directly conducted through in-vivo real-time assay.

• Korean Journal of Optics and Photonics
• /
• v.28 no.2
• /
• pp.75-82
• /
• 2017

We present a new type of receiver-transmitter optical system that can be adapted to the sensor head of a displacement-measuring interferometer. The interferometer is utilized to control positioning error and repetition accuracy of a wafer, down to the order of 1 nm, in a semiconductor manufacturing process. Currently, according to the tendency of scale-up of wafers, an interferometer is demanded to measure a wider range of displacement. To solve this technical problem, we suggest a new type of receiver-transmitter optical system consisting of a GRIN lens-Collimating lens-Afocal lens system, compared to conventional receiver-transmitter using a single collimating lens. By adapting this new technological optical structure, we can improve coupling efficiency up to about 100 times that of a single conventional collimating lens.

• The Korean Journal of Applied Statistics
• /
• v.30 no.6
• /
• pp.993-1004
• /
• 2017

A stratified sampling method is generally used with a sample selected using the same sample weight in each stratum in order to improve the accuracy of the sampling survey estimation. However, the weight should be adjusted to reflect the response rate if the response rate is affected by the value of the variable of interest. It may be also more effective to adjust the weights by subdividing the stratum rather than using the same weight if the variable of interest has a linear relationship with the continuous auxiliary variables. In this study, we propose a method to increase the accuracy of estimation using an informative sampling design technique when the response rate is an exponential function of the variable of interest and the variable of interest has a linear relationship with the auxiliary variable. Simulation results show the superiority of the proposed method.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.125-132
• /
• 2009

In this study we could contribute to the development of a precise checking tool with which the reliability of the automatic fire detection systems was enhanced and the safety of the people was ensured. In the same way as the domestic technical standard, the portable smoke sensitivity tester, which was developed in this work, could be used to check the capability of the smoke detectors installed in the field. Its heater inside was warmed up to $400^{\circ}C$ in 40 seconds and the paper as a smoke source was burned to produce smoke for the test. With the Photoelectric smoke detector it was possible to measure and control the smoke concentration in a range from 0%/m to 25%/m. With the adjustment of rpm of the fan, it was possible to keep a constant wind velocity in a range from 20cm/sec to 40cm/sec.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.216-223
• /
• 2012

The effect of water back-flushing period (FT) was investigated in hybrid process of carbon fiber microfiltration membrane and photocatalyst for advanced drinking water treatment in this study, and compared with the previous study using alumina ultrafiltration membrane. The FT was changed in the range of 2~10 min with fixed 10 sec of BT. Then, the FT effects on resistance of membrane fouling ($R_f$), permeate flux (J) and total permeate volume ($V_T$) were observed during total filtration time of 180 min. As decreasing FT, $R_f$ decreased and J increased, which was same with the previous result using alumina ultrafiltration membrane. The treatment efficiency of turbidity was high beyond 99.2%, and the effect of FT was not shown on treatment efficiency of turbidity, which was different with the previous result. The treatment efficiency of organic matters was the lowest value of 65.6% at NBF, and it increased as decreasing FT, which was different with the previous result, too. The reason was that the membrane fouling phenomena could show a different mechanism depending on ceramic membrane materials.

• Membrane Journal
• /
• v.19 no.2
• /
• pp.136-144
• /
• 2009

In this study, sodium dedocyl sulfate (SDS), which was anionic surfactant, was added for forming micelles to remove ferrous ions that could be contained with a small amount in industrial water. Then aggregates were formed by adsorption or binding of ferrous ions on the surface of micelles, and then rejected by ceramic membranes to remove ferrous ions. Ferrous concentration was fixed at 1mM and SDS was changed as $0{\sim}10mM$ to investigate the effect of the anionic surfactant. As a result, rejection rate of ferrous was the highest to 88.97% at 6mM. And we used ELS (Electrophoretic Light Scattering Spectrometer) to investigate particle size distribution of micellar aggregates depending on SDS concentration. Then distribution of large aggregates was the highest at 6mM. And we investigated effects of $N_2$-back-flushing time (BT) during periodic $N_2$-back-flushing on ceramic membranes. Finally optimal $N_2$-BT for NCMT-723l (pore size $0.10{\mu}m$) membrane was 20 sec.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.148-148
• /
• 2016

홍수범람지도는 치수 대책 수립 등 다양한 목적으로 국내 주요하천에서 작성되고 있으며 범람 구역의 정확도를 높이기 위한 노력이 다각도로 수행되고 있다. 최근, 공간적으로 매우 정밀한 LiDAR 측량 성과를 기반한 DEM을 이용하거나 2차원 혹은 3차원 수치모델링을 적용하여 범람지도의 정확성 및 적용성이 획기적으로 개선되고 있다. 또한, 범람구역의 불확도에 관련된 연구도 다수 수행되고 있다. 그러나, 이러한 성과는 정밀 DEM 자료가 가용하거나 치수의 중요도가 높은 국가하천 지역에 국한되고 있으며 중소하천을 포함한 국가 전체 홍수지도 작성은 여전히 제한적으로 수행되고 있다. 중소하천의 경우, 공간해상도 및 정확도가 낮은 DEM과 1차원 모델링에 기반하여 범람지도의 신뢰도가 여전히 낮은 실정이다. 또한, 홍수지도 작성 기법은 비교적 잘 알려진 상황이나 작성 과정은 상당한 시간이 필요한 작업으로 지도 작성 시 실무에서 많은 비용과 시간이 소요되고 있어, 결과적으로 중소하천을 포괄한 홍수범람지도 작성에 장애요인으로 작용하고 있다. 따라서, 본 연구에서는 기존 하천기본계획에서 확보될 수 있는 하도단면 측량 등 표고 측량 성과를 활용하여 공간 해상도가 상대적으로 낮은 DEM을 정교화 및 상세화할 수 있는 개선기법 및 복잡한 범람지도 작성과정을 자동화하여 작성 소요시간을 현저히 줄일 수 있도록 하는 GIS 기반의 홍수범람지도 작성 자동화 툴을 개발하였다. 개발된 GIS 기반의 자동화 툴은 AIM(Automated Inundation Mapping tool)로 명명되었으며 ESRI사의 ArcObjects를 활용하여 개발되어 ArcGIS 기반으로 운영되며 현재 HEC-RAS 홍수위 자료가 입력자료로 작동되도록 설계되었다. 개선된 DEM과 AIM은 시범적으로 제주도 한천 하류에 적용되었으며 2007년 태풍 나리 시 발생한 범람흔적도와 비교했을 때 기존 방식에 비해 범람지도의 정확도와 작성시간(10초 가량 소요)이 상당부분 개선되었다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.10
• /
• pp.1280-1287
• /
• 2020

This paper proposes a vision-based food recognition method for automated production of custom cakes. A small camera module mounted on a food art printer recognizes objects' shape and estimates their center points through image processing. Through the perspective transformation, the top-view image is obtained from the original image taken at an oblique position. The line and circular hough transformations are applied to recognize square and circular shapes respectively. In addition, the center of gravity of each figure are accurately detected in units of pixels. The test results show that the shape recognition rate is more than 98.75% under 180 ~ 250 lux of light and the positioning error rate is less than 0.87% under 50 ~ 120 lux. These values sufficiently meet the needs of the corresponding market. In addition, the processing delay is also less than 0.5 seconds per frame, so the proposed algorithm is suitable for commercial purpose.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.13-20
• /
• 2023

The process of microelectromechanical system (MEMS) fabrication involves surface treatment to impart functionality to the device. Such surface treatment method is the self-assembled monolayer (SAM) technique, which modifies and functionalizes the surface of MEMS components with organic molecule monolayer, possessing a precisely controllable strength that depends on immersion time and solution concentration. These monolayers spontaneously adsorb on polymeric substrates or metal/ceramic components offering high precision at the nanoscale and modifying surface properties. SAM technology has been utilized in various fields, such as tribological property control, mass-production lithography, and ultrasensitive organic/biomolecular sensor applications. This paper provides an overview of the development and application of SAM technology in various fields.