• Korean Journal of Optics and Photonics
• /
• v.9 no.1
• /
• pp.1-4
• /
• 1998

A compact scanning confocal microscope has been constructed using a quad-detector in a CD-player. The variation of error signal on depth which obtained by a quad-detector is used in the scanning confocal microscope. Bipolar error signals, which is sensitive near a focus, give a surface following effect whiout following the surface. In the case of small depth difference, the difference of materials through the reflection signal has been identified. The image which uses reflection signal only, has been obtained with the same setup. And, the results obtained in two different way were compared and analyzed.

• Korean Journal of Optics and Photonics
• /
• v.7 no.2
• /
• pp.101-111
• /
• 1996

Optical microscopes integrated with CCD cameras are widely used for automatic inspection of precision circuit patterns fabricated on glass masks and silicon wafers. For this application it is important to position the object always is focus so that the image appears in good quality while the microscope scans the object. However, as the magnification of the microscope is taken large for fine resolution the depth of focus becomes small, often in submicron ranges, requiring special care in focusing. This study proposes a new auto-focusing method, which can be readily incorporated in existing optical configuration of microscope. This method is based on optical triangulation using a separate beam of laser and two photodiodes, eliminating focus errors caused by surface roughness and waviness. Experimental results prove that the method can produce focus error signals which are very sensitive with a resolution of 5 nm within 0.5 ${\mu}{\textrm}{m}$ accuracy.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.221-222
• /
• 2017

본 논문에서는 위치 센서에 의존하지 않는 매입형 영구자석 전동기의 센서리스 구동 시 전압 왜곡으로 인해 나타나는 위치 추정 오차를 이론적으로 분석하고자 한다. 특히, 추정 d축에 맥동하는 구형파 전압을 주입하는 방법에서 주입하는 신호의 주파수에 따라 위치 추정 성능이 달라지는 현상에 초점을 맞춘다. 무부하에서 스위칭 주파수의 신호를 주입할 때 전압 왜곡은 on/off sequence에서 서로 반대의 위상을 갖는 역상분 2고조파의 형태로 나타나며, 위치 추정 오차는 3고조파의 형태로 나타난다. 반면, 반스위칭 주파수의 신호를 주입하는 경우에는 샘플링 주기 동안 주입 전압 왜곡의 효과가 상쇄되기 때문에 인덕턴스의 영향만이 주로 고려되어 위치 추정 오차가 6고조파의 형태로 나타난다. 시뮬레이션과 실험을 통해 이론적 분석의 타당성을 검증하였다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.97-103
• /
• 2014

Signal processing technique of linear frequency modulation-frequency shift keying (LFM-FSK) waveform has been introduced for rear view radars of an automobile. LFM-FSK waveform consists of two sequential stepped frequency waveforms with some frequency offset, and thus, can be used to generate inverse synthetic aperture radar (ISAR) images of rear view target of an automobile. However, ISAR images can often be blurred due to inter-pulse phase errors. To resolve this problem, one-dimensional (1-D) entropies of high resolution range profiles (HRRP) are minimized with the help of particle swarm optimization (PSO). The searching space used in PSO is adaptively adjusted by the use of information on the target's velocity obtained from LFM-FSK waveforms. Simulation results show that the proposed method can generate well-focused ISAR images.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.583-590
• /
• 2004

The autofocus is one of the important processes in the automated vision inspection or measurements using optical microscopes, because it influences the measuring accuracy. In this paper, we used the confocal microscope configuration based on not a pinhole but a single-mode optical fiber. A single mode fiber has the functions of source and detector by applying the reciprocal scheme. As a result, we acquired a simple system configuration and easy alignment of the optical axis. Also, we embodied a fast autofocus system by acquiring the focus error signal through a source modulation technique. The source modulation technique can effectively reduce physical disturbances compared with objective lens modulation, and it is easily applicable to general optical microscopes. The focus error signal was measured with respect to the modulation amplitude, reflectance of the specimen and inclination angle of the measuring surface. The performance of the proposed autofocus system was verified through autofocusing flat mirror surface. In addition, we confirmed that source modulation rarely degrades the depth resolution by the comparison between the FWHMs of axial response curves.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.11
• /
• pp.894-901
• /
• 2017

In the existence of motion, azimuth phase error due to accuracy limitation of GPS/IMU and system delay is unavoidable and it is essential to apply autofocus to estimate and compensate the azimuth phase error. In this paper, autofocus algorithm using MWLS(Modified WLS) is proposed. It shows the robust performance compared with original WLS using new target selection/sorting metric and iterative azimuth phase estimation technique. SAR raw data obtained in a captive flight test is used to validate the performance of the proposed algorithm.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.165-168
• /
• 1997

We have constructed a scanning confocal microscope using a 780 nm semiconductor laser, an actuator of a compact disk player and a quad-detector. This device detects heights and characteristics of a surface. The laser focus was located at the surface of a sample by using the error signal obtained by a quad-dector, and the current supplied to the actuator for lens was displayed as a height. The materials of a surface were classified according to reflected total intensities and was displayed by different color in a monitor. The device has very samll dimensions of 30 mm$\times$20 mm$\times$20 mm and scan field is 1.6 mm$\times$1.6mm. We obtained two images, one using only reflected light and the other using an error signal from a quad-detector and compared these two images.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.257-258
• /
• 2006

This paper presents the displacement sensor based on astigmatic method that has a small measurement range. The sensor has the characteristic that the measuring range is changed easily by exchanging a objective lens or distance between a objective lens and a collimator lens. The measuring range and resolution is evaluated by a laser interferometer.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.7
• /
• pp.81-89
• /
• 2017

Autofocus(AF) Method is essential to overcome the performance degradation due to motion measurement errors under airborne SAR environment. In this paper, back-projection algorithm(BPA) is applied to SAR raw data acquired under the squinted mode, and preprocessing algorithm of AF for BPA is investigated. To apply AF to SAR image effectively, image backplane rotation method and doppler location alignment function for BPA are proposed. The proposed method is applied to SAR raw data acquired in a flight test and shows excellent performance improvement in real data.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.4
• /
• pp.233-238
• /
• 2009

In this paper, we propose the methods to select the stable region for the detect region which is required in the system used the face to the ROI in the auto-focus digital camera. this method regards the face region as the ROI in the progressive input frame and focusing the region in the mobile camera embeded ISP module automatically. The learning algorithm to detect the face is the Adaboost algorithm. we proposed the method to detect the slanted face not participate in the train process and postprocessing method for the results of detection, and then we proposed the stabilization method to sustain the region not shake for the region. we estimated the capability for the stabilization algorithm using the RMS between the trajectory and regression curve.