• Magazine of the Korea Concrete Institute
• /
• v.5 no.3
• /
• pp.161-168
• /
• 1993

본 연구는 아스팔트 콘크리트의 채움재로서 제강더스트의 사용가능성을 실험을 통하여 분석하였다. 실험에는 제강더스트의 기본물성시험과 혼합물의 비교시험을 포함시켰다. 비교시험에서는 채움재로서 석회석분을 사용하는 경우와 제강더스트를 사용하는 경우, 채움재와 아스팔트를 혼합한 필리-비투먼, 그리고 골재까지 혼합한 아스팔트 콘크리트에 대하여 물성을 비교분석하였다. 실험결과 제강더스트는 포장용 채움재의 규정을 만족시키며, 제강더스트를 채움재로 사용한 아스팔트 콘크리트보다 우수하며, 제강더스트는 아스팔트 혼합물용 채움재로써 충분히 사용가능한 것으로 밝혀졌다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.26-26
• /
• 2020

하천수의 수심을 유지하기 위하여 설치된 콘크리트 취수보 대신 강자갈이나 쇄석을 채움재로 하는 돌망태를 사용하게 되면 토사퇴적으로 인한 건천화나 상, 하류 수생태계 단절과 같은 문제를 어느 정도 감소시킬 수 있을 뿐만 아니라, 자갈접촉산화작용에 의한 수질개선과 공사비 절감 효과 등의 장점이 있다. 그러나 돌망태는 투수성이므로 불투수성인 콘크리트 보다 저류측면에서 불리하다. 콘크리트 취수보에서의 흐름은 보 정점의 형상, 보의 폭, 높이, 그리고 월류수심에 좌우되며, 베르누이 방정식과 연속방정식에 의해 방류량 산정식을 유도하고, 유량계수와 같은 실험상수를 결정하여 방류량을 계산한다. 돌망태 취수보의 흐름은 보의 높이, 보의 길이, 보의 상류수심 외에 채움재의 형상, 입경, 배치상태가 흐름에 영향을 미친다. 따라서 콘크리트 취수보에 적용되었던 기존의 방류량 산정식을 그대로 적용할 수 없다. 돌망태 보의 통과류는 실험상수가 포함된 비선형 수두손실방정식으로 표현할 수 있다. 실험상수는 비표면적의 크기를 의미하는 채움재의 평균동수반경와 관계되며, 평균동수반경은 채움재 입자의 형상으로 부터 구할 수 있다. 따라서 실험을 통하여 채움재 입자의 형상과 크기에 따른 실험상수와 평균동수반경의 관계를 구하면 비선형 수두손실방정식으로부터 통과류의 방류량을 계산할 수 있게 된다. 본 연구는 돌망태 취수보가 대수층함양 원수 공급시설물로서 타당한가를 평가하기 위하여 수행되었다. 콘크리트 취수보의 월류량 계산은 기존의 방류량 산정식을 이용하였으며, 돌망태 취수보는 실험상수와 평균동수반경의 기존관계식을 이용하여 통과류의 방류량을 계산하였다. 이와 같이 계산된 각각의 수심-방류량 관계로 부터 수심을 비교하였다. 동일한 유량조건에서 돌망태 취수보의 상류수심은 콘크리트 취수보보다 작게 계산되었다. 상류수심은 돌망태 채움재 입자의 크기가 작을수록 증가하여, 돌망태 취수보는 채움재의 입자크기가 작을수록 저류성능이 개선됨을 알 수 있었다. 따라서 돌망태 취수보는 채움재의 입경이 작을수록 콘크리트 취수보의 저류수준에 접근할 수 있을 것으로 판단되었다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.101-107
• /
• 2017

Over-break, which is excavated larger than planned line at tunnel excavation, is inevitable due to the nature of blasting. But regarding the bottom of the foundation, most of the domestic ordering organizations pay only 10 cm thick filled concrete when pouring concrete due to over-break. In accordance, the construction cost will increase greatly if all the depths of the designed over-break are filled only with concrete. When tunnel excavation occurs, concrete filling of 18 MPa(T = 100 mm) and 150 mm~237 mm auxiliary concrete layer and 240 mm concrete track(TCL) are applied to the upper part. The concrete is installed in an excessive amount of about 600 mm between the lower part of the rail and the tunnel rock bed. Therefore, in this study, it is necessary to analyze the concrete crack structure according to the depth of the existing tunnel and the modified tunnel section, and to evaluate the adequacy of the required thickness of the tunnel floor concrete for securing the crack stability of the concrete.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.305-312
• /
• 2017

This paper presents a laboratory investigation into the effects of fillers using industrial by-product such as coal ash, IGCC slag on properties of hot-mixed asphalt concrete variation with filler content. For comparison, existing mixture with lime and dust have also been considered. Marshall and flow test has been considered for the purpose of mix design as well as evaluation of mixture. Other performance tests such as indirect tensile strength test, tensile strength ratio(moisture susceptibility), dynamic stability have also been carried out variation with filler content. It is observed that the mixes with industrial by-product exhibit conform with quality standard. Therefore, it has been recommended to utilize industrial by-product based on fly ash wherever available, not only reducing the produce cost but also partly solve the industrial by-product utilization and disposal problem.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.2368-2373
• /
• 2012

In this research, finite element method was carried out to evaluate the defomation of pipe and surface displacement for backfill of underground ficility. Various conditions for analysis were employer, including two different pipes(PE and concrete pipe), two different excavation depth(60cm and 150cm) and width(1.5D and 2D), a regular sand backfill, and four different flowable backfills. The vertical deformation of 60 cm diameter for PE was measured three times more than that of 30 cm diameter. The measured deformations for regular backfill and four flowable backfills were 0.320mm, and 0.135mm to 0.155mm, respectively. It ratio was around 40%. In case of 30cm diameter of concrete pipe, the measured vertical defomation was around 0.004mm for all the backfill materials. In case of installation depth, the effect of flowable backfill for flexible pipe is better than for rigid pipe. There is little effect on the deformation of concrete pipe with regular sand backfill and flowable backfill.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.85-93
• /
• 2016

In this study, finite element analyses of masonry infilled frames using a general purpose FE program, ABAQUS, were conducted. Analysis models consisted of the bare frame, infilled frames with masonry wall thickness of 0.5B and 1.0B, respectively. The masonry walls were constructed using the concrete bricks which were generally used in Korea as infilled wall. The material properties of frames and masonry for the analysis were obtained from material tests. However, four times increased the tensile strength was used for 1.0B wall, which is seemingly due to the differences in locating the bricks. The force-displacement relation and development of crack from the FE analysis were very similar to those from the experiments. From the FEA results, contact force between the frame and masonry, distribution of shear force and bending moments in frame members were analyzed. Obtained contact stress shows a trianglur distribution, and the contact length for 0.5B speciment and 1.0B specimen were close to the value estimated using ASCE 41-06 equation and ASCE 41-13 equation, respectively. Obtained shear force and bending moment distribution seems to replicate actual behavior which originates from the contact stress and gap between the frame and masonry.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.90-97
• /
• 2018

The quantities of electronic waste have been increased rapidly, and was caused variety problems such as environmental pollution or dissipation of resource. So, it needed to development of recycling technology about heavy metal in the electronic waste. Meanwhile, filler material (concrete or mortar) was used for shielding radioactive waste, however, it did not used materials that it is proved radiation shielding performance. So, there is a lack of confidence in the shielding performance. Therefore, in this paper, mechanical properties of concrete was evaluated for the applicability using electronic waste as fine aggregate of filler material. From the test results, compressive and flexural strength and elasticity modulus and the micro pore in the $1{\mu}m$ range was significantly affected by substitution of electronic waste, however, it could be improved the performance by using mineral admixture as binder. So, it is shown that the electronic waste could be applicable as fine aggregate of filler material.

• Land and Housing Review
• /
• v.2 no.4
• /
• pp.553-558
• /
• 2011

Existing method protruding strands that are embedded in PHC pile to connect pile head and foundation slab shows poor constructibility. As this causes crack and damage in pile head and casualties often occurs in construction site during the work, alternative method called one-cutting method, in which pile above the ground surface and strands embedded in pile are completely cut and pile head is reinforced with rebar for connection with foundation slab, is currently adopted. However, the capacity of details for these methods are not mechanically proved. In this study, in order to suggest proper details of reinforcement for one-cutting method, failures due to lack of shear resistance between infilled concrete and PHC pile are analyzed through experiments and embedded depth with infilled concrete inside PHC pile is suggested. Assuming that slip failure strength is 0.4MPa, which is obtained from experiment conservatively, to have rebar yielded before slip failure, minimum depth of infilled concrete for PHC 450 and PHC 500, need to be 600mm above, and for PHC 600, 1,000mm above.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.3
• /
• pp.77-84
• /
• 2021

In this study, flexural tests of prestressed high strength spun concrete (PHC) piles reinforced with infilled concrete and longitudinal rebars were conducted, where the longitudinal rebar ratio and the presence of sludge formed on the inner surface of PHC pile were set as key test variables. A total of six PHC pile specimens were manufactured, and their flexural behaviors including failure mode, crack pattern, longitudinal strain distribution in a section and end slip between external PHC pile and infilled concrete were measured and discussed in detail. The test results revealed that the flexural stiffness and strength increased as the longitudinal rebar ratio became larger, and that the sludge formed on the inner surface of PHC pile did not show any detrimental effect on the flexural performance. In addition to the experimental approach, this study presents a nonlinear flexural analysis model considering compatibility conditions and strain and stress distributions of the PHC piles and infilled concrete. The rationality of the nonlinear flexural analysis model was verified by comparing it with test results, and it appeared that the proposed model well evaluated the flexural behavior of PHC piles reinforced with infilled concrete and longitudinal rebars with a good accuracy.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.3
• /
• pp.147-155
• /
• 1992

최근들어 성능이 우수하고 품질이 높은 새로운 건설소재를 개발하려는 노력이 계속되고 있다. 본 논문에서는 고강도화 및 연성확보를 위하여 폴리머 콘크리트에 섬유를 혼입한 섬유보강 폴리머 콘크리트를 제조하여 강도 및 역학적 특성을 규명하고자 하였다. 이를 위하여 포괄적인 실험연구를 수행하였으며 주요실험변수로는 강섬유의 혼입량과 채움재(filler)의 혼입량, 그리고 양생온도를 주요변수로 선정하였다. 강섬유의 혼입량은 체적비로 0%, 1%, 2%로 변화시켰으며, 채움재와 수지의 비는 1.0과 1.5로 하였다. 본 연구결과 섬유의 혼입으로 인하여 압축강도, 휨강도, 인장강도 모두 증가하였으며, 특히 인장강도의 증가가 더 크게 나타났다. 양생온도가 증가한 경우 폴리머의 중합반응이 좋아져 강도가 증가하였다. 또한 본 논문에서는 섬유보강 폴리머 콘크리트의 응력-변형도 관계곡선을 도축하였으며, 이것은 구조설계시 중요한 기초가 될 것으로 사료된다.