• Journal of Korean Society of Transportation
• /
• v.27 no.6
• /
• pp.109-118
• /
• 2009

The conventional lane changing model has been developed without acceleration or deceleration of vehicles at target lane. Thus, existing lane changing models have limitation to apply in real world. In this paper, lane changing model considered acceleration or deceleration, and calculated the safety distance between subject vehicle and adjacent vehicles for lane changing as well. Simulation was conducted to verify the validity and the efficiency of the developed lane changing model in this paper. Several scenarios were carefully examined by safety distance between subject vehicle and adjacent vehicles. In the result, it was verified that if gap between subject vehicle and adjacent vehicles is larger than safety distance, lane changing behavior between subject vehicle and adjacent vehicles avoids collision. The suggested lane changing model may be applied at the future driver assistance system and advanced safety vehicle.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.2
• /
• pp.273-279
• /
• 2019

Development of mountain area is increasing due to the demand for improvement of traffic convenience and development of underdeveloped area. Therefore, there frequently are sections where tunnels and interchanges are located close to each other. These sections do not only affect tunnel planning, types and length of interchanges, but also affect more on route selection. In Korea, several design criteria present each reference value but these values are very similar. In the situation, the minimum value among them is usually applied when planning roads and it could cause traffic safety problems in different site conditions. In this study, the problems of design speed, illuminance adaptation distance, and lane change intervals are analyzed by simulating the cases that the problem could occur when calculating the separation distance between tunnel and interchange. The results obtained from this study can be summarized as following: the driving speed should be applied in case that the site has a big gap between design speed and driving speed because the uniform application of the design speed is not safe; the illuminance adaptation distance should include the influence distance in the section affected by the direct light; in addition, the lane change distance should include the time to perceive the situation of the next lane after the lane change in the section required for successive lane change.

• Journal of Korean Society of Transportation
• /
• v.22 no.6
• /
• pp.145-157
• /
• 2004

Microscopic freeway simulation models project the uncertain values of performance measures for subject traffic conditions by explaining drivers' driving behavior with lane changing and car-following models. However, the existing lane changing models are limited to gap acceptance oriented passive behavior of drivers and not able to capture more-or-less aggressive driving behavior(e.g. cut-in lane changing) ordinarily obseved in field. This paper suggests the definition of cut-inlane changing and presents its characteristics based on the findings from two different freeway on- and off-ramp sections. In addition, this paper proposes a new lane changing model capable of handling both passive and active drivers' driving behavior for better performance of simulations. The proposed lane changing model was tested with Hanyang Simulatin (HYTSIM), a microscopic freeway simulation program developed for this study. The HYTSIM simulation results reflecting the performance of the proposed lane changing model were compared against the field data. The test results showed that the distribution of gaps collected when vehicles change lanes were statistically identical to the field data at 95% confidence level.

• Journal of Korean Society of Transportation
• /
• v.28 no.4
• /
• pp.177-186
• /
• 2010

The principal objective of this paper is to develop road design guidelines, especially for managed lane access spacing between the expressway on-ramp (or off-ramp) and managed lane access point. Managed lanes are typically located in the expressway median and are accessed by weaving across the mainlines. The high level of lane-changing activity present in weaving areas affects capacity significantly. One promising tool for the analysis of lane-changing activity is "gap acceptance theory." This paper estimates the capacity of weaving areas based on the estimated degree of traffic turbulence using gap acceptance theory. The degree of traffic turbulence is represented by a function of the probability that lane-changing vehicles can complete their maneuvers successfully in a given weaving distance. In developing road design guidelines based on the developed gap acceptance model, the minimum managed lane access spacing is determined where the capacity with respect to the managed lane access spacing becomes stable.

• Journal of Korean Society of Transportation
• /
• v.26 no.1
• /
• pp.203-213
• /
• 2008

U-Turn offers convenience to drivers. U-Turn increases efficiency of traffic flow. But Standard of U-Turn is not clear. It caused many problems of traffic flow and traffic safety. This study estimate length between U-Turn location with front intersection based on stopping sight distance and left-turn vehicle's queue length. Variables are used traffic volume and operation speed. This study Analysis of U-Turn vehicle's behaviors and classification of conflict form by investigation. U-Turn length estimating based on relationship analysis between conflict with U-Turn length. Variables are used lane changing angles and operation speed. This study estimates length between U-Turn location with back intersection based on gap acceptance theory. Variables are used traffic volume, operation speed and lane changing angles. So, U-Turn location and length estimated considering traffic flow and traffic safety.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1D
• /
• pp.65-72
• /
• 2011

When an expressway intersects another expressway, a unique connector needs to be designed between the two consecutive exit ramps. In such a case, it is important to design a connector such that there is enough distance for drivers to find their way safely. A current design manual in Korea prescribes the minimum length of the connector as 240 m. In this research, we have suggested a method for calculating the minimum length of a connector in order to check the feasibility of the currently prescribed length. For this purpose, we have attempted to determine the total perception-reaction time and lane-changing time required by a driver. For determining the driver's perception-reaction time, we have used the driver's decision time in addition to the conventional 2.5 s of perception-reaction time for stopping sight distances. We have considered both the design speed and the average travel speed for the calculation of the length. To evaluate the accuracy of the new method, we have chosen four sites on expressways for which relatively high accident rates were recorded. As a result, we could verify that the current limit (240 m) was sufficient for drivers to be able to change lanes in the given specific geometry. However, the prescribed limit should be revised in case the drivers' decision time is considered to be their perception-reaction time. All new approaches for calculating the ideal length of a connector have been carried out by taking into account the design speed as well as the average travel speed. Owing to the characteristics of the specific geometry for two consecutive exit ramps and the large difference between the design speed and the average travel speed in the objective areas, it is more realistic to use the proposed method by keeping the decision time equal to a driver's perception-reaction time, in order to determine the ideal distance that should be maintained between two consecutive exit ramps.

• Journal of Korean Society of Transportation
• /
• v.20 no.4
• /
• pp.73-82
• /
• 2002

The influence of bus stops near signalized intersections is one of the important factors which cannot be negligible in the analysis of the capacity of signalized intersections. Absence of consideration of bus bay can reduce capacity and increase the time that the stop of buses block other traveling vehicles. This influence is reflected by the bus blockage adjustment factor in KHCM, but the factor does not consider the course of each bus passing the intersection. Particularly, left turn buses have more influence on the capacity than the other buses and require the minimum length of the road for lane changes. All the existing criteria can apply only to arterial roads on which mostly traffic flows are continuous. And the criteria. which can determine the optimum location and the minimum distance between a signalized intersection and a bus bay, is not prepared and the related study is insufficient. Therefore, a theoretical formula is derived in this study being based on the theories which are avaliable to apply to the situation of signalized intersections.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.3
• /
• pp.67-76
• /
• 2007

Although Hi-pass have been operated for alleviating traffic congestion and enhancing mobility in expressways since 2000, there is not any standard for safe operation. For that reason, we investigated about tubular markers, which is a typical facility for safety in Hi-pass. Tubular Markers are installed for separating same or opposite traffic flows spatially, supporting the marks at a place which has not only high possibility of accidents but distinguished carefulness of drivers. In this paper, it is noted two considerings; one is prevention of accident from the speed gap of autos and Hi-pass vehicles; the other is guarantee of necessary distance that Hi-pass vehicles could be changes the lanes for off-ramp. Focusing those considerations, it is proposed not only prefer distance of tubular markers, but also fundamental basic subjects. We anticipate that the results of this study would be useful reference in more safe and efficient tollgate operation of Hi-pass.

• Journal of Korean Society of Transportation
• /
• v.26 no.5
• /
• pp.51-62
• /
• 2008

An innovative feature of this study is to propose a methodology for evaluating safety performance in real time based on vehicle trajectory data extracted from video images. The essence of evaluating safety performance is to capture unsafe car-following and lane-changing events generated by individual vehicles traveling within video surveillance area. The proposed methodology derived three indices including real-time safety index(RSI) based on the concept of safe stopping distance, time-to-collision(TTC), and the collision energy based on the conservation of momentum. It is believed that outcomes would be greatly utilized in developing a new generation of video images processing(VIP) based traffic detection systems capable of producing safety performance measurements. Relevant technical challenges for such detection systems are also discussed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.6
• /
• pp.124-140
• /
• 2017

There exists a limitation to provide proper advance information for safe maneuvering through guidance and caution signs in freeway mobile work zones, unlike fixed work zones. Although a work-protection vehicle is currently deployed at the rear of the work vehicle, more active countermeasures to prevent crashes are required. The purpose of this study was to propose a method to evaluate the safety in mobile work zones and to present effective countermeasures. Driving simulation experiments were conducted to analyze characteristics of driver's behavior in mobile and fixed work zones. Safety distance index (SDI) based on the comparison of stopping distances of a work-protection vehicle and a following subject vehicle was used to evaluate traffic safety. More dangerous driving behavior was observed in the mobile work zone. Especially, it was identified that the lane-change of vehicles following the work- protection vehicle was late. Therefore, it is necessary to actively introduce methods to provide warning information so that the driver can recognize the work-protection vehicle in advance and carry out appropriate evasive maneuvers.