• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1360-1366
• /
• 2000

KHST project plans to design and to build an high speed train. There are noise requirements in passenger room for the standing and running train, which should be reached. Noise prognosises are calculated for the standing and running TM5(Motorized car) and TT4(Trailer car) train (v=300km/h) to find out critical areas in or around the train. On those areas, actions of noise reduction are proposed to reach the requirements. Finally noise prognosises are calculated for the higher velocity of v=350km/h.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.11
• /
• pp.1144-1150
• /
• 2009

Appropriate vibration model is required to predict in advance the vibration level of a large vehicle which carries sensitive electronic/mechanical equipments and drives often on the unpaved and/or off-road conditions. Central tire inflation system(CTIS) is recently adopted to improve the mobile operation of military and bulletproof vehicles. In this paper, full vehicle model(FVM) having 11 degrees of freedom and equipped with CTIS has been developed for a large vehicle which has $8\times8$ wheels$\times$driving wheels. Usability of the developed model is validated via road tests for three different modes (i.e. highway, country, and mud/sand/snow modes) and for various velocity conditions. The developed FVM can be used to predict the vibration level of the large vehicle as well as to determine the driving velocity criterion for different road conditions.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.227-233
• /
• 1999

Simple equations which can predict "exact" values of the natural frequency of vibration for the special orthotropic laminates are presented. Many laminates with certain orientations have decreasing values of $B_{16}$ and $B_{26}$ as the number of plies increases. Such laminates, with $D_{16}=D_{26}{\rightarrow}0$, including the laminates with anti-symmetric configurations can be solved by the same equation for the special orthotropic laminates. If the quasi-isotropic constants are used, the equations for the isotropic plates can be used. Use of some coefficients cab produce "exact" value for laminates with such configurations. Natural frequencies of the plate with varying aspect ratios is presented.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1268-1273
• /
• 2003

This paper presents a case history of piping failures on power plant. The root cause of the failure was defined to set the optimal countermeasures. The failure comes from transient vibration and the 1st stress increased at the hydraulic oil supply system of control valves for high pressure steam turbine.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.104-108
• /
• 2002

In this study, the dynamic absorbing system for the shoulder-fired system with high-level-impact force has been investigated. for this purpose, firstly, mathematical model based on the short recoil system has been constructed. In order to design the dynamic absorbing system, parameter sensitivity analysis and parameter optimization process have been performed under constraints of moving displacement and transmitted force. In order to enhance the efficiency of energy dissipation, the stroke-dependent variable damping system has been analyzed. finally, the performance of the designed dynamic absorbing system has been evaluated by simulation with respect to the benchmark system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.471-477
• /
• 2003

The floating ring seal is often used in the turbopump (TP) unit of liquid rocket engine (LRE) owing to its inherent ability of minimizing the leakage flow and superior dynamic characteristics as well. This paper describes the test results concerned with the lock-up and dynamic characteristics of the floating ring seals in the turbopump. The characteristics of the floating ring seals were extracted from the frequency response function (FRF) by instrumental variable method. The experiment was tested at 7.0MPa and 0-24,800 rpm. And the test results were introduced about the dynamic characteristics of floating ring seal related with the eccentricity and attitude angle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.339-345
• /
• 2002

When a flow passes a series of parallel ones, vortexes will be formed in the wake after the cylinder. This paper treats the problems of vibration and noise in tube bank of gas flow duct of heat exchanger thermal suppling boiler in combine cycle thermal power plants. The boiler burner type has recently been changed to low Nox burner and begun commercial operation. After more load up operation then 70%, high level noise and vibration were generated at gas flow duct of heat exchanger.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.856-857
• /
• 2014

국내에서 이용되는 예측모델은 국립환경과학원식, 도로공사의 HW-NOISE, KHTN, 소음지도에 이용되는 외국의 RLS90, NMPB 등이 있다. 이러한 예측모델은 예측 방법 및 표현에 따라 예측식 2D(국립환경과학원식, HW-NOISE)와 3D로 예측(KHTN, RLS90, NMPB 등)으로 구분할 수 있다. 본 연구는 도로 주변 공동주택에서의 소음실측 및 예측식별 예측값을 통하여 예측식의 오차 및 오차의 원인을 분석하고 예측식의 적용방법에 대하여 고찰하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.699-700
• /
• 2014

고속도로에 아스팔트 저소음포장이 시공된 현장의 소음조사를 통하여 저소음 아스팔트 포장의 소음저감효과를 분석하였다. 교통량 및 시공시기에 차이가 있는 세 현장에 대하여 측정 시기를 달리하여 저소음포장의 사용 기간에 따른 소음저감효과의 변화를 분석하였으며, 공동주택의 소음대책을 위해 시공된 현장에서는 세대내에서 실질적인 저감효과에 대해 분석하였다. 이 결과를 토대로 저소음포장을 도로소음 대책수단으로 적용을 검토할 경우 설계자가 고려해야할 사항을 제시하고자 하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.419-422
• /
• 2014

Floor impact sound level is affected by various factors. This study was examined about impact sources and floor coverings influenced at floor impact sound. So this study wishes to get method to reduce sound pressure level of receiving room. Light-weight impact sound in mid frequency and Heavy-weight impact sound in low frequency was affected by floor coverings. Therefore, method to reduce floor impact sound level is to use proper floor coverings. Some coverings can amplify the heavy-weight impact sound in low frequency. Floor impact sound sources used measurement and analysis were standard heavy-impact source(Tapping, Bang, Ball) and living impact sources(Cleaner, Chair, Toy-car, Soccer ball). And Floor coverings used measurements were various thickness vinyl, laminate(or ply-wood) floor. Especially vinyl floor coverings were very effective method to reduce floor impact.