• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.354-354
• /
• 2015

코팅 층과 소지 사이의 접합력 평가를 위하여 박리 시험법(Peel Off Test), 블리스터 시험법(Blister Test), 압입균열 시험법(Indentation Test), 직접 인장 시험법(Direct Full Off Test), 스카치 테이프 시험법(Scotch Tape Test), 그리고 스크래치 시험법(Scratch Test) 등이 사용되어 왔다. 이 중 박리 시험법과 스카치 테이프 시험법이 산업계에서 일반적으로 사용되고 있다. 전자 산업계에서 많이 사용되고 있는 박리시험법은 금속박막과 절연체 기판 사이의 접합력을 간단하게 측정할 수 있으며, 실험값의 재현성이 뛰어난 장점이 있다. 또한, 측정하는 동안 만들어지는 박리 곡선(Peel Curve)로부터 분석의 신뢰성 여부를 확인할 수 있다. 이러한 장점에도 불구하고 박리 시험법 특성 상 금속 코팅층의 강도가 금속 피막/기판간 접합 강도를 초과하여야 하기 때문에 수백 nm 이하의 박막의 접합력 측정에는 적용하기가 어렵다. 이에 반하여, 스카치 테이프 분석법은 일정길이의 접착 테이프를 박막 표면에 붙인 후 다시 떼어내면서 접착력을 평가하는 방법으로, 박막의 접합력 평가에 적용이 가능하다. 그러나 이 방법은 합격 불합격 여부를 판정하는 정성적인 방법으로 정량평가가 어렵다. 또한, 박막에 접착 테이프를 붙일때의 압력, 테이프를 박리할 때의 각도 및 속도를 일정하게 제어하기가 쉽지 않아 결과의 신뢰성이 높지 않다. 스크래치 테스트는 탐사침(Stylus)을 이용하여 박막의 표면에 하중을 증가시키면서 기판을 이동하여, 피막의 균열이나 박리될 때의 임계 하중값 (Critical Load; Lc)을 측정하는 방법이다. 이 방법은 시편 준비가 쉽고 간단하여 빠른 분석이 가능하고, 수백 nm 이하의 박막에도 적용 가능하다. 또한, 접합력을 정량화 할 수 있기 때문에 변수에 따른 접합력 비교가 용이하다는 장점이 있다. 이와 같은 분석적 장점에도 불구하고, 스크래치 시험을 통한 접합력 측정 방법은 아직까진 산업적으로 널리 활용되지 못하고 있다. 따라서, 본 연구에서는 스크래치 테스트의 원리 및 이론에 대하여 간략히 알아보고, 스크래치 분석을 이용한 접합력 비교에 대한 실제 사례들을 소개하고자 하였다.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.82-87
• /
• 2013

Preliminary studies on the synthesis of magnetic nanoparticles including nanoporous carbon materials have been done via a direct carbonization process from resol, ferric nitrate and triblock copolymer F127. The results show that the nanoporous magnetite/carbon ($Fe_3O_4$/carbon) with a low $Fe_3O_4$ content (1 wt%) possesses an ordered 2-D hexagonal (p6mm) structure, uniform nanopores (3.6 nm), high surface areas (up to 635 $m^2/g$) and pore volumes (up to 0.48 $cm^3/g$). Magnetite nanoparticles with a small particle size (10.2 nm) were confined in the matrix of amorphous carbon frameworks with superparamagnetic property (7.7 emu/g). The nanoporous magnetite/carbon showed maximum adsorption amount (995 mg/g) of ibuprofen after 24 h at room temperature. The nanoporous magnetite/carbon was separated from solution easily by using a magnet. The nanoporous magnetite/carbon material is a good adsorbent for hydrophobic organic drug molecules, i.e. ibuprofen.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.102-109
• /
• 2019

The material constitution of multi-layered thin film coated on the PET base film was analyzed using ATR FT-IR and pyro GC/MS combination. The cross section of the film was acquired by cracking the film after dipping in liquid nitrogen and was observed using optical microscope. Total thickness of the coated film was $70{\mu}m$ and three layers were observed. Since each layers were too thin to analyze directly except the surface layer, analyzable area of each layers were exposed by using a proper solvent and were investigated using ATR FT-IR and pyro GC/MS. Results shows that three layers were commonly consisted of urethane-acrylate copolymers. Also, inorganic and/or metal inclusions detected by XPS and SEM-EDAX were exhibited by nano size $SiO_2$ particles in layer(1) and aluminum flakes in layer(2).

• Restorative Dentistry and Endodontics
• /
• v.35 no.1
• /
• pp.5-12
• /
• 2010

The purpose of this study was to evaluate the pulp tissue reaction to direct pulp capping of mechanically exposed beagle dogs' pulp with several capping materials. A total of 36 teeth of 2 healthy beagle dongs were used. The mechanically exposed pulps were capped with one of the followings: (1) Mineral Trioxide Aggregate (MTA: $ProRoot^{(R)}$ MTA. Dentsply, Tulsa, USA), (2) Clearfil SE Bond (Dentin adhesive system: Kuraray, Osaka, Japan), (3) Ultra-Blend (Photo-polymerized Calcium hydroxide: Ultradent, South Jordan, USA), (4) Dycal (Quick setting Calcium hydroxide: LD Caulk Co., Milford, USA) at 7, 30, and 90 days before sacrificing. The cavities were restored with Z350 flowable composite resin (3M ESPE, St. Paul. MN, USA). After the beagle dogs were sacrificed, the extracted teeth were fixed, decalcified, prepared for histological examination and stained with HE stain. The pulpal tissue responses to direct pulp capping materials were assessed. In MTA calcium hydroxide, and photo-polymerized calcium hydroxide groups, initial mild inflammatory cell infiltration, newly formed odontoblast-like cell layer and hard tissue bridge formation were observed. Compared with dentin adhesive system, these materials were biocompatible and good for pulp tissue regeneration. In dentin adhesive system group, severe inflammatory cell infiltration, pulp tissue degeneration and pulp tissue necrosis were observed. It seemed evident that application of dentin adhesive system in direct pulp capping of beagle dog teeth cannot lead to acceptable repair of the pulp tissue with dentine bridge formation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.4
• /
• pp.232-243
• /
• 2021

Purpose: The purpose of this study was to evaluate the shear bond strength of various 3D printed denture base resins and the conventional denture base resin to various denture relining materials. Materials and Methods: For denture base materials, a heatcured (Vertex RS) and two types of 3D printed DENTCA Denture base II, NextDent^TM Base) were used. And 4 types denture relining materials (Tokuyama Rebase II fast, Kooliner, Denture Liner, Denture Liner, Lang Jet Denture Repair Kit) with different components were used. It was classified into 12 groups. Adhesion was performed between the resin base and the relining materials in accordance with ISO/TS 11405 standard. The shear bonding strength was measured, and then the adhesion interface was observed with a stereoscopic microscope and a scanning electron microscope. The fracture pattern was investigated through the analysis of the fragment. Results: In the 3D printed denture resin group, the shear bonding strength with relining materials was significantly lower than that of the heat-cured resin group (P < 0.05). The group of polymethyl methacrylate -based relining materials, high shear bonding strength was shown regardless of the type of denture. As for the fracture pattern, adhesive fracture appeared in most groups, and cohesive, mixed fracture appeared in some groups. Conclusion: The polymethyl methacrylate -based denture relining materials showed high shear bonding strength values compared to other denture relining materials. But, for direct methods, it is considered advantageous in terms of shear bonding strength to use a isobutyl methacrylate-based denture relining materials.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.96-104
• /
• 2010

We suggest here a cost-effective replica fabrication method for transparent and hard molds for imprinting lithography such as NIL and S-FIL. The process starts with the use of a replica hard mold from a master, using a polymer copy as a carrier. The polymer copy as a carrier was treated by soluble process for forming anti-adhesion layer. Duplicated hard molds can eliminate direct contact between a hard master and a patterned polymer on a substrate and the generated contamination of a master during the imprinting process. The replica hard mold exhibits the glass-like properties introduced here, such as transparency and hardness, make it appropriate for nanoimprint lithography and step-and-flash imprint lithography.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.290.2-290.2
• /
• 2013

X-선 튜브는 의료 영상 및 치료, 산업용 제전 장치, 비파괴 X-선 영상 장치 등에서 사용되는데 기존의 열전자원을 이용한 X-선 튜브와는 달리, 냉음극형 X-선 튜브는 빠른 속도의 디지털 구동이 가능하며 전력 소비가 낮은 장점이 있다. 따라서, 최근 많은 연구자들에 의해서 냉음극형 X-선 튜브에 관한 연구가 활발하게 진행되고 있다. 냉음극형 X-선 튜브는 전계 방출을 이용한 전자원을 사용하며, 탄소나노튜브 (CNT), Si, 다양한 종류의 나노선 등이 대표적이다. 그 중에서 CNT는 높은 종횡비로 인해 전계 방출 특성이 우수하여 가장 대표적인 물질이다. CNT를 이용한 전자원을 제작하기 위해서는 직접 성장법, 전기영동법, 스크린 프린팅법, 디핑법 등 다양한 방법이 존재한다. 직접 성장법을 제외한 방법들은 모재료인 CNT와 용매, 금속재료들을 섞어 페이스트나 수용액의 상태를 제작하여야 한다. 이 때, 금속 재료는 기판과 CNT간의 접착 및 전자 전도 통로의 역할을 하는 무기 충전제이며 일반적으로 나노 혹은 수 마이크로미터 크기의 상태로 존재하는 것을 주로 사용한다. X-선 튜브 제작은 일반적으로 외벽을 유리 혹은 세라믹을 주로 사용하는데 아노드 전극 및 캐소드 전극 등과 결합하여 진공 밀봉된 형태가 되어야 한다. 브레이징 방법은 금속과 세라믹을 결합하는데 매우 유용한 방법이며, 그 중에서도 진공 브레이징 방법은 다량의 부품을 한 번에 결합시킬 수 있다. 하지만 진공 브레이징 공정의 온도는 약 $700{\sim}1,000^{\circ}C$이며 이는 금속 재료가 충분히 증발할 수 있는 온도가 된다. 본 발표에서는 고온 진공 상태에서의 무기 충전제의 증발에 대한 현상을 관찰하고 고온진공 상태에서 증발없이 무기 충전제로의 역할을 할 수 있도록 다양한 금속 및 합금에 대한 연구를 수행하였다. 또한, 이 연구를 통해 선택된 무기 충전제를 포함하여 CNT 페이스트를 볼밀링 방법을 이용하여 제작하였으며, 이를 이용한 CNT 에미터가 X-선 튜브의 전자원으로 사용될 수 있는지 확인하기 위해 전계 방출 실험을 함께 실시하였다. 제작된 CNT 에미터가 우수한 전계 방출 특성을 가지고 있음을 확인하였으며, 이는 본 연구를 통해 선택된 금속 및 합금 재료가 무기 충전제로의 역할을 잘 수행하고 있음을 보여준다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.5
• /
• pp.135-141
• /
• 2021

As a trend of lightening automobiles and electronic products, several studies are currently underway to replace parts of metals with resins. In particular, heterojunctions between metals and resins are now under the spotlight. This study aims to evaluate the variation in bonding strength with process conditions when the polybutylene terephthalate (PBT) polymer is bonded to a specimen of the lightweight 6061 aluminum alloy (AL6061). Conditions of the bonding surface of the AL6061 specimen, the temperature of the injection mold, and the content of the glass fiber were considered to be process variables. Bonded specimens were manufactured for different values of these variables. Bonding strength tests were then performed on these specimens and variations were analyzed in their characteristics corresponding to those of the process conditions. Fractures in these specimens were assessed using scanning electron microscopy (SEM) to assess the fracture surface. This was then used to analyze the fracture shape and determine whether anodizing the specimen led to the development of cracks on the joint surface. Results of the above test indicated that while the surface condition of the specimen and the temperature of the injection mold significantly influenced the strength of bonding, the content of the glass fiber did not.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.73-74
• /
• 2010

The objective of this research is to improve the flexural capacity of RC Beams. To delay prematured tension failure of concrete specimen and to improve flexural capacity of RC beam by increasing the contribution of FRP strengthening plates, a method for inserting a laminate to the interface between concrete and FRP materials. This method makes it possible to increase overall flexural performance of RC beam by FRP plate compared to normal RC beams and RC beam strengthened by bonded FRP plates. The new bonding technique is applicable to all types of reinforcement available FRP laminate, and in principle is also applicable to materials other than FRP.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.6
• /
• pp.83-101
• /
• 2002

Elastic waves provide an important information about the soil mass in the near-surface. Soil properties in relation to elastic wave parameters are clarified to facilitate the application of geophysical technique to soil characterization. As an example, experiments are performed to gain further insight into the behavior of unsaturated particulate materials using bender elements. The small strain stiffness is continuously measured on specimens subjected to drying, and changes in stiffness are related to changes in interparticle forces such as capillarity, bonding due to ion sharing, buttress effect due to fine migration, and cementation due to salt precipitation. The rate of menisci regeneration is studied after a perturbation as well. Finally, several phenomena associated with the evolution of capillary forces during drying are identified.