• Polymer(Korea)
• /
• v.32 no.4
• /
• pp.385-389
• /
• 2008

Chain propagation and chain transfer in anionic polymerization of hexafluoropropylene oxide were investigated under various reaction conditions such as the stabilization of reaction temperature, the amount of hexafluoropropylene solvent, and the feeding rate of hexafluoropropylene oxide monomer. Anionic initiator for the polymerization was synthesized from cesium fluoride and hexafluoropropylene oxide in tetraethyleneglycol dimethylether. It was possible to obtain a high molecular weight poly(HFPO) ($M_w$ 14800) using the anionic initiator in conditions of stabilized reaction temperature, and optimized addition of solvent and monomer feeding (HFP/initiator mole ratio=31.5 and HFPO feeding rate=11.67 g/hr). Otherwise, chain transfer reaction in anionic polymerization was increased. From the results of molecular weight in various reaction conditions, it was found that chain propagation and chain transfer in anionic polymerization of HFPO were very sensitive to reaction conditions.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.600-605
• /
• 2013

In this study, the bulk polymerizations of L-lactide were carried out with triethylaluminium (TEAL), which was supported inside of the nanopore of silica. The feed amount of TEAL in the feed, the immobilization time and temperature were changed to observe the effect of immobilization condition on the polymerization performance with the silica- supported TEAL. As the feed amount of TEAL increased, the conversion of polymerization increased. The highest molecular weight (MW) was achieved at 8 mmol/g-silica of TEAL. Hexane and toluene as solvents were employed to investigate the effect of temperature on the immobilization. Hexane showed better efficiency of immobilization TEAL and the immobilization temperature at $50^{\circ}C$ showed the highest conversion and MW.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.410-414
• /
• 2002

The late transition Pd catalyst of low oxophilicity that has ferrocene -based diimine ligand for stabilization of center metal had been synthesized and applied for the polymerization of methyl methacrylate (MMA). In the presence of triisobutylaluminium (TIBA) for impurity scavenger, the effects of polymerization temperature and [TIBA]/[Pd] mole ratio on the yield and glass transition temperature ($T_g$) of PMMA had been examined. For 40~$50^{\circ}C$ of polymerization temperature and 2000~3000 of [TIBA]/[Pd] mole ratio, higher polymer yields were obtained. It was observed that ($T_g$) of PMMA is almost independent to the polymerization temperature but influenced by the [TIBA]/[Pd] mole ratio. With the examination of($T_g$) of PMMA with the structure of polymer, it had been found that T$_{g}$ of PMMA exhibits a linear relationship with the isotacticity of polymer.r.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.229-236
• /
• 1998

In this paper, thin films of Polyimide (PI) were fabricated by vapor deposition polymerization method (VDPM) of dry processes. The film's properties with curing temperature and electrical properties were studies. The synthesis of hexafluoroisopropyliden-2,2-bis[phthalic anhydride](6FDA) and 4, 4'-diamino diphenyl ether (DDE) was carried out by vapor deposition polymerization(VDP) with the same deposition rate. The evaporation temperature of 6FDA and DDE were $214^{\circ}C$ and $137^{\circ}C$, respectively, so as to preserve balance of stoichiometry. The polymic acid (PAA) made by VDPM were changed to PI by thermal curing. The uniformity and density of PI thin films were increased according to increasing curing temperature. The relative permittivity and dissipation loss factor were 3.7 and 0.008 at the frequency of 100Hz~200KHz, respectively, for the fabricated in the curing temperature of $300^{\circ}C$. Also, the resistivity was about 1.05$\times$$ 10^{15}$$\Omega$cm at $30^{\circ}C$.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.35 no.3
• /
• pp.477-486
• /
• 2008

Acrylic resin is widely used in dental practice. However, the residual monomer in acrylic resin could act as a negative biocompatability on human body. The aim of this study was to evaluate the amount of the monomer elution from polymerized orthodontic acrylic resin. Orthodontic acrylic resin was used in the study. The curing condition of the resin was controlled by temperature, pressure, aquatic and atmospheric environment. The duration and amount of monomer elution and timedependent plot was recorded by high performance liquid chromatography. The result showed that the only monomer eluted from the resin was methyl methacrylic acid. And the amount of the monomer elution has diminished considerably by time progress especially within 24 hours. Furthermore, elution of the residual monomer was significantly lower in group of pressure, moisture and elevated temperature than control (p<.05). According to this study, it was thought that the elution of residual monomer might be influenced by curing environment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.3
• /
• pp.431-438
• /
• 2003

This study investigates pulp chamber temperature rise during composite resin polymerization by plasma arc(Group III : Flipo 3 sec, Group IV : Flipo 5 sec) and LED curing units(Group V : Lux-O-Max, 40 sec) as well as conventional halogen lamp curing units(Group I : VIP mode3, 20 sec, Group II : VIP mode6, 20 sec). The results are as follows : 1. All of the investigated pulp chamber temperature rises are lower than the boundary temperature could result in irreversible damage to the pulpal tissue ($5.5^{\circ}C$). 2. In the group II, it is found the significantly higher pulp chamber temperature rise than any other groups(p<0.05). 3. In the group of composite resin light-cured with VIP, it is found the significantly higher pulp chamber temperature rise in the group II than group I(p<0.05). 4. In the group of composite resin light-cured with Flipo, it is found the significantly higher pulp chamber temperature rise in the group IV than group III (p<0.05). 5. In the case of comparing VIP and Flipo, group II is significantly higher pulp chamber temperature rise than group III, IV(p<0.05), and group IV is significantly higher pulp chamber temperature rise than group I(p<0.05), and it does not significantly differ between group I and III. 6. In the group of composite resin light-cured with Lux-O-Max, it is found the significantly lower pulp chamber temperature rise than any other groups (p<0.05).

• Journal of Adhesion and Interface
• /
• v.15 no.3
• /
• pp.93-99
• /
• 2014

Monodisperse poly[styrene-co-(COPS-I)] latices in the size range of 165~550nm were successfully prepared by soap-free emulsion polymerization with various polymerization conditions (Styrene, COPS-I, KPS, DVB concentrations and polymerization temperature). In general, the COPS-I and KPS, DVB concentrations and polymerization temperature were closely related to the polymerization rate and the number of particles, molecular weight, and zeta potential. The polymerization rate and zeta potential increased, but molecular weight decreased, with increasing in the number of particles.

• Proceedings of the KAIS Fall Conference
• /
• 2003.06a
• /
• pp.337-339
• /
• 2003

본 연구에서는 여러 종류의 담체 중에서 Davison 952 실리카를 선택하여 실리카 표면의 하이드록시기의 양을 진공 열처리 방법을 사용하여 조절하였다. 표면 처리된 실리카를 사용하여 담지촉매를 제조한 후 폴리에틸렌(PE) 중합을 수행, 소성온도에 따른 실리카 표면의 하이드록시기 양의 변화와 담지되는 조촉매(MAO) 및 메탈로센 촉매의 양과의 상관관계를 조사하였고 실리카 표면처리와 중합 활성도 간의 상관관계를 고찰하였다. 폴리에틸렌(PE) 중합 결과 메탈로센 촉매가 가장 많이 담지된 200℃ 보다 400℃ 또는 600℃에서 메탈로센 당(g PE/mol Zr)활성도가 높았으며, 담체에 흡착된 MAO와 메탈로센의 비율이 400℃와 600℃에서 가장 크게 나타났다.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.437-444
• /
• 2000

Propylene polymerizations were carried out by using rac-Et(Ind)$_2$ZrCl$_2$ (Zirconocene catalyst) and a commercial third generation Ziegler-Natta catalyst in a semibatch reactor. From the polymerization reactions, the optimum reaction conditions and the physical properties of polymers produced from each catalyst system were investigated. The optimum reaction temperatures of rac-Et(Ind)$_2$ZrCl$_2$ and Ziegler-Natta catalyst were 5$0^{\circ}C$, 4$0^{\circ}C$, respectively. On the basis of the results for the produced polymer particle size distributions and the catalytic activities of polymerization reaction, the reaction temperature should be considered as an important factor for the successful polymerization reactions. Especially, the polymer was conglomerated in the higher reaction temperature. It was found that there was an upper limitation to co-catalyst concentration. Reaction rates and polymer yields rather decreased with increasing the concentration of to-catalyst, i.e., MAO and TEAl affected only polymerization activities, but the PEEB in Ziegler-Natta catalyst system affected isotactic indexes of produced polymer as well as activities. Based on these observations, the production yield seems to exhibit a first order lineal relationship to the partial pressure of monomer.

• Journal of dental hygiene science
• /
• v.15 no.3
• /
• pp.259-264
• /
• 2015

For this experiment, specimen was manufactured by injecting polymer and monomer into silicon mold with volume ratio of 2.5:1 based on ISO 20795-2 so that average thickness, width and length of specimen would be maintained as 3.3 mm, 10.0 mm and 65.0 mm, respectively depending on spray on technique. Specimen was divided into 3 groups ($25^{\circ}C$, $40^{\circ}C$, $70^{\circ}C$) depending on polymerization temperature and 10 specimen was manufactured for each group and it was polymerized in water tank of ${\pm}1^{\circ}C$ under the setting condition of polymerization time of 15 minutes and pressure of 3 bar. After keeping specimen in distilled water of $37^{\circ}C$ for over 48 hours before experiment, flexural strength (FS) and elasticity modulus (EM) of specimen being tested by using Intron (3344; Instron; Instron). SPSS ver. 16.0 was used for analysis and post-hoc test of Scheffe was performed after using one-way ANOVA. When comparing mean value of FS of resin for orthodontics, it was represented in the range of 71.500 MPa for $25^{\circ}C$ group, 74.920 MPa for $40^{\circ}C$ group and 76.880 MPa for $70^{\circ}C$ group and difference was shown in the order of $25^{\circ}C$ group <$40^{\circ}C$ group <$70^{\circ}C$ group but such difference was not significant statistically (p=0.052). Result of EM mean value of resin for orthodontics was more polymerization temperature was high, the more was significant difference represented in the order of $25^{\circ}C$ group <$40^{\circ}C$ group <$70^{\circ}C$ group (p<0.039).