• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.120-127
• /
• 1996

Anti-lock Brake System has been developed to reduce tendency for wheel lock and improve vehicle control during sudden braking on slippery road surfaces. This is achieved by controlling the braking pressure, avoiding wheel lock, while retaining handling and brake performance. This paper is concerned about pressurecharacteristics of hydraulic modulator. Experimental sets which is consists of hydraulic modulator, duty controller, pressure regulator, pressure senset is consuructed. System modelling and computer simulation are performed for comparison with experimental results. Brake wheel pressure are measured under various driving pulse. The result of experiment show fairly agreement with the simulation. As a result, it is known that wheel pressure is affected by duty ratio, orifice diameter through computer simulation.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2080-2093
• /
• 2008

Disk brake system take charge of maximum braking energy among the mechanical brake systems for high speed train. For this reason, Metallic friction materials and heat resistant steel disk is adopted at disk brake system for high speed train. It was investigated tribological characteristics(friction coefficient, friction stability, wear rate and braking temperature) between some kinds of metallic friction materials and heat resistant steel disk. Cu-based friction material for high speed train have suitable tribological characteristics.

• Journal of Auto-vehicle Safety Association
• /
• v.12 no.2
• /
• pp.7-13
• /
• 2020

Recently, there is a big issue of downsizing on brake system according to fuel efficiency and regenerative braking cooperation control. Especially, small cars have improved in a variety ways such as electric vehicle and smart car compared to previous small cars. So, small brake system is strongly required in the car industry. A new small brake system for light compact vehicles was proposed in this paper. For this system, the solid type disc and caliper were newly developed. And the important design factors were considered to reduce brake size. First, we calculated the temperature rise of disc through heat capacity formula and CAE analysis. Second, we analyzed the housing and carrier stiffness of caliper to select the reasonable condition. Finally, the superiorities of the developed brake system were verified by heat capacity, consumption liquid level, braking feeling, judder, wear test and regenerative braking cooperation control analysis. A developed brake system is expected to be useful for brake system of light compact platform.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.8-13
• /
• 2014

The effect of several parameters to minimize the braking response time has been investigated in this study. The experimental rigs were developed and the results of the experement compared with those of simulation obtained from the net work fluid flow system analysis code (FLOWMASTER). The braking response time and pressure loss were observed at separated braking port and found out that the response time can be reduced by considering the pipe length and environmental thermal conditions. The correlation equation was also presented to predict the pressure loss at various tank pressure.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.7
• /
• pp.535-540
• /
• 2016

The braking device in railway vehicles decelerates or stops the train by dissipating the thermal energy converted from kinetic energy into the air. Therefore, the brake system is crucial for safety. In this paper, we performed a study on an electromechanical brake actuator using an electrical motor as an alternative to pneumatic air cylinders to reduce the idle running time in braking, which subsequently increases braking distance, and to ensure reliable response characteristics. Especially, to analyze the response characteristics of the electromechanical brake actuator, we measure the delay time, response time and power consumption compared to the air cylinder. It is confirmed that the electromechanical brake actuator can reduce reaction time by 0.1 seconds (Braking Action) and 0.46 seconds (Brake Release) compared to the air cylinder.

• Journal of Advanced Navigation Technology
• /
• v.17 no.1
• /
• pp.132-141
• /
• 2013

In this paper, method using electric braking from stop area to high-speed area was presented in order to improve air-brake. And electric braking method can be improved environmental problems, efficiency, economy, etc. Method for electrical complete braking are two ways that method of inserting series resistance between the motor and the inverter, and method of inverter output voltage increase. In this paper, use series resistance insert method because economical and easy to apply. In addition, Series resistor is used short circuit method for reduce the power loss. In improved efficiency and the laboratory environment for secure braking, resistance insert method and inverter output voltage increase method showed same characteristics in all areas.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.1
• /
• pp.85-90
• /
• 2011

To maintain the safety and efficiency of railroad vehicles, it is important to understand the working of the brake system with anti-skid control unit (ASCU) for rolling stocks. In this paper, a HILS (Hardware In-the Loop Simulations) system with ASCU hardware (for logic) and a DSP board (for dynamics) is developed to analyze skidding of the Hanvit-200 train during the process of braking. Experimental results are presented for the case that the skid on one of the four wheels is artificially generated using a Simulink model. A convenient GUI is prepared using ControlDesk of dSPACE.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.4
• /
• pp.191-197
• /
• 2012

In this paper, method using electric braking from stop area to high-speed area was presented in order to improve air-brake. And electric braking method can be improved environmental problems, efficiency, economy, etc.. Method for electrical complete braking are two ways that method of inserting series resistance between the motor and the inverter, and method of inverter output voltage increase. In this paper, use series resistance insert method because economical and easy to apply. In addition, Series resistor is used short circuit method for reduce the power loss. In improved efficiency and the laboratory environment for secure braking, resistance insert method and inverter output voltage increase method showed same characteristics in all areas.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.4
• /
• pp.335-341
• /
• 2010

The electric braking system obtains its braking force by a motor instead of the hydraulic brake which has been used in conventional automobile systems. Electric braking system is consisted of fewer numbers of components than hydraulic braking system, and it has effects of improved response and reduced braking distance for the ABS(Anti-lock Brake System) and ESC(Electronic Stability Control). This paper presents the BLAC motor drive system for Electro-Magnetic Brake(EMB). Proposed control system consists of the power converter for driving a motor and the digital control system for speed control, and the vector control is applied for fast torque response. It is verified through the simulation using Matlab/Simulink and experiment that the proposed BLAC drive system can be applied to EMB.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.127-137
• /
• 2012

In this paper, method using electric braking from stop area to high-speed area was presented in order to improve air-brake. And electric braking method can be improved environmental problems, efficiency, economy, etc. Method for electrical complete braking are two ways that method of inserting series resistance between the motor and the inverter, and method of inverter output voltage increase. In this paper, use series resistance insert method because economical and easy to apply. In addition, Series resistor is used short circuit method for reduce the power loss. In improved efficiency and the laboratory environment for secure braking, resistance insert method and inverter output voltage increase method showed same characteristics in all areas.