• Journal of Advanced Navigation Technology
• /
• v.17 no.5
• /
• pp.524-544
• /
• 2013

In this paper, A tow system of miniature establishes each motor to individual 1C1M methods to control for a permanent magnet synchronous motors (PMSM) is constructed. You assume that is wiring having had the ability that can all absorb regenerative power which occurred when permanent magnet synchronous motors(PMSM) brake is all used to it, and to occur about agreement use scope expansion my electricity. To regenerative braking power securities of a PMSM and to stop of the bronzes my a control security, and that the electricity as you apply to vector control method and an speed sensor of controller to microprocessor, And you studied to speed, motor electricity energy control method to the algorithm and you brake a revival by regenerative braking power securities of a permanent magnet synchronous motors. It is proposed that motor control method to the algorithm you brake a revival by electricity braking power securities, you do to simulations regarding a momentum load and experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.9
• /
• pp.835-842
• /
• 2016

In Korea, urban railway cars are typically maintained using the strategy of predictive maintenance. In an effort to overcome the limitations of the existing strategy, there is increased interest in adopting the condition-based maintenance strategy. In this study, a novel method is proposed to detect faults in the solenoid valves of the braking system in urban railway vehicles. We determined the key component (i.e., solenoid valve) that leads to braking system faults through the analysis of failure modes, effects, and criticality. Then, an equivalent circuit model was developed with the compensation of the temperature effect on solenoid coils. Finally, we presented how to detect faults with the equivalent circuit model and current signal measurements. To demonstrate the performance of the proposed method, we conducted a case study using real solenoid valves taken from urban railway vehicles. In summary, it was shown that the proposed method can be effective to detect faults in solenoid valves. We anticipate the outcome from this study can help secure the safety and reliability of urban railway vehicles.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.893-900
• /
• 2016

Output response for prototype system is analyzed according to the pole locations and the damping ratio changes. The system modeling is constructed for RLC-circuit and the output response is analyzed for both a unit-step and a sinusoidal input. The survey is conducted to estimate the understanding ability on the automatic control. A high understanding ability is shown up in analysing the transfer functions of control system. And improvement is manifest in the ability to understand the output response according to the parameter changes. But some difficulty is revealed in acquiring the output responses in time domain.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.591-597
• /
• 2017

This study is to develop a vehicle Integrated Dynamics Control System(IDCB) that can stabilize the lateral dynamics and maintain steerability. To accomplish this task, an eight degree of freedom vehicle model and a nonlinear observer are designed. The IDCB independently controls the brake systems of four wheels with a fuzzy logic control and a sliding model control. The result shows that the nonlinear observer produced satisfactory results. IDCB tracked the reference yaw rate and reduced the body slip angle under all tested conditions. It indicates that the IDCB enhanced lateral stability and preserved steerability.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.519-528
• /
• 2019

Current brake system changes the kinetic energy into heat energy by friction-type of brake that the braking action is diverging into the air. The system has a device called a retarder that generates braking force. High-tech research on the high-speed response characteristics of retarders utilizing part of the braking energy of the retarder to save electrical energy consumption is already underway in advanced countries. In this paper, we propose DC-DC converter which converts 3-phase voltage generated from retarder to 24V DC voltage for battery charging and verify its validity through experiments.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.1
• /
• pp.97-104
• /
• 2024

In this study, combustion experiments were conducted to assess engine performance and exhaust gas characteristics using four blends of 1-pentanol and diesel as fuel in a naturally aspirated 4-stroke diesel engine. The blending ratios of 1-pentanol were 5, 10, 15, and 20% by volume. The experiments were carried out under four different engine torque conditions (6, 8, 10, and 12 Nm) while maintaining a constant engine speed of 2,000 rpm for all fuel types. The results showed that the use of 1-pentanol/diesel blended fuel generally led to a decrease in brake thermal efficiency, attributed to the low calorific value of the blend and the cooling effect due to the latent heat of vaporization. Additionally, both brake specific energy consumption and brake specific fuel consumption increased. However, the use of the blended fuel resulted in a general decrease in NOx concentration, a decrease in CO concentration except some conditions, and a reduction in smoke opacity across all conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.3
• /
• pp.315-321
• /
• 2014

This paper presents an integrated chassis control system with fail safety using optimum yaw moment distribution for a vehicle with steer-by-wire and brake-by-wire devices. The proposed system has two-level structure: upper- and lower-level controllers. In the upper-level controller, the control yaw moment is computed with sliding mode control theory. In the lower-level controller, the control yaw moment is distributed into the tire forces of active front steering(AFS) and electronic stability control(ESC) with the weighted pseudo-inverse based control allocation(WPCA) method. By setting the variable weights in WPCA, it is possible to take the sensor/actuator failure into account. In this framework, it is necessary to optimize the variables weights in order to enhance the yaw moment distribution. For this purpose, simulation-based tuning is proposed. To show the effectiveness of the proposed method, simulations are conducted on a vehicle simulation package, CarSim.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.470-476
• /
• 2019

The braking force for a train is generally provided by compressed air. The pressure valve system that is used to apply appropriate braking forces to trains has a complex flow circuit. It is possible to make a channel shape that can increase the flow efficiency by 3D printing. There are restrictions on the flow shape design when using general machining. Therefore, in this study, the compressed air flow was analyzed in a pressure valve system by comparing flow paths made with conventional manufacturing methods and 3D printing. An analysis was done to examine the curvature magnitude of the flow path, the diameter of the flow path, the magnitude of the inlet and reservoir pressure, and the initial temperature of the compressed air when the flow direction changes. The minimization of pressure loss and the uniformity of the flow characteristics influenced the braking efficiency. The curvilinear flow path made through 3D printing was advantageous for improving the braking efficiency compared to the rectangular shape manufactured by general machining.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.2247-2248
• /
• 2006

전동차 운행시스템은 속도를 지령하는 NOTCH의 상태를 전압으로 인식하여 주파수로 변환한 후 주파수 변환신호를 출력하는 아날로그 및 디지털 인코더와 인코더의 주파수 변환신호를 입력받아 카운트하여 노치의 상태를 데이터버스(DATA BUS)에 실어 중앙처리장치(CPU)에 데이터를 출력하는 특징을 갖는다. 이런한 전동차 신호전달시스템 분석을 본 연구에서 하고자 한다.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.615-616
• /
• 2006

전동차 운행시스템은 속도를 지령하는 NOTCH의 상태를 전압으로 인식하여 주파수로 변환한 후 주파수 변환신호를 출력하는 아날로그 및 디지털 인코더와 인코더의 주파수 변환신호를 입력받아 카운트하여 노치의 상태를 데이터버스(DATA BUS)에 싶어 중앙처리장치(CPU)에 데이터를 출력하는 특징을 갖는다. 이러한 전동차 신호전달시스템 분석을 년 연구에서 하고자 한다.