• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.20-40
• /
• 2003

Since unloaded Q-value of a high-temperature superconductor(HTS) filter is very high, a bandpass filter(BPF) and a lowpass filter(LPF) with an increase of pole numbers can be fabricated without an increase of an insertion loss(IL) ; recently a 70-pole BPF is developed in USA. They have an abrupt skirt property and an excellent attenuation level for out-of band. Moreover, they can be miniaturized when lumped element resonators or the slow-wave characteristic are used. Technology of fabricating a HTS epitaxial film as well as a film of a 4 inch area also makes the planar type filter with a various structure and an enhanced power handling capability possible. Recently, the HTS filter subsystems composed of a planar-type HTS filters, a GaAs-based LNA and a mini-cryocooler are developed. The extended receiver front- end subsystems for mobile radio communications decrease the noise-figure level of the communication system and the frequency interference interacted adjacent bands, and increase the efficiency of frequency and the capacity of communication system. In this paper, theory for developing the HTS filter, its kinds, its design rules, its characteristics are reviewed. The feature of the research and market trends related to the HTS filter systems for the receiver front-end subsystem of mobile base station are surveyed.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.152-157
• /
• 2007

AlGaN/GaN high electron mobility transistors (HEMTs) were fabricated and the effect of ${N_2}O$ plasma on the electrical characteristics of the devices was investigated. The HEMT exposed to ${N_2}O$ plasma formed by 40 W of RF power in a chamber with pressure of 20 mTorr at a temperature of $200^{\circ}C$, exhibited a reduction of gate leakage current from 246 nA to 1.2 pA by 10 seconds treatment. The current between the two isolated active regions reduced from 3 uA to 7 nA and the sheet resistance of the active layer was lowered also. The variations of electrical characteristics for HEMT were occurred within a short time expose of 10 seconds and the successive expose did not influence on the improvements of gate leakage characteristics and conductivity of the active region. The reduced leakage current level was not varied by successive $SiO_2$ deposition and its removal. The transconductnace and drain current of AlGaN/GaN HEMTs were increased also by the expose to the ${N_2}O$ plasma.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.4 s.346
• /
• pp.8-15
• /
• 2006

In this paper, the 94 GHz, low conversion loss, and high isolation single balanced mixer is designed and fabricated using GaAs-based metamorphic high electron mobility transistors (MHEMTs) with 70 nm gate length and the hybrid ring coupler with the micromachined transmission lines, dielectric-supported air-gapped microstrip lines (DAMLs). The 70 nm MHEMT devices exhibit DC characteristics with a drain current density of 607 mA/mm an extrinsic transconductance of 1015 mS/mm. The current gain cutoff frequency ($f_T$) and maximum oscillation frequency ($f_{max}$) are 320 GHz and 430 GHz, respectively. The fabricated hybrid ring coupler shows wideband characteristics of the coupling loss of $3.57{\pm}0.22dB$ and the transmission loss of $3.80{\pm}0.08dB$ in the measured frequency range of 85 GHz to 105 GHz. This mixer shows that the conversion loss and isolation characteristics are $2.5dB{\sim}>2.8dB$ and under -30 dB, respectively, in the range of $93.65GHz{\sim}94.25GHz$. At the center frequency of 94 GHz, this mixer shows the minimum conversion loss of 2.5 dB at a LO power of 6 dBm To our knowledge, these results are the best performances demonstrated from 94 GHz single balanced mixer utilizing GaAs-based HEMTs in terms of conversion loss as well as isolation characteristics.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.6
• /
• pp.28-34
• /
• 1999

We fabricated a planar ultra-violet photodetector whose ohmic and schottky contacts were respectively formed with evaporated Al and Pt on the GaN layer. To examine the applicability of the device to the UV sensor, we investigated its electrical and optical characteristics. The GaN layer on the sapphire waver had $7.8{\times}10^{16}cm^{-3}$ of doping concentnation and the $138 cm^2/V{\cdot}s$ of electron mobility and it absorbed the spectrum of the light below 325 nm wavelength. It had the responsivity of 2.8 A/W of at 325 nm, and the signal to noise ratio(SNR) of $4{\times}10^4$, and the noise equivalent power(NEP) of $3.5{\times}10^9$W under 5 V reverse bias. These results confirmed that the GaN schottky diode had a solar blind properly when it was applied to the UV photodetector.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.15-22
• /
• 2008

In this paper, we propose a numerical analysis on reversed current of distributed amplifier based on transmission line theory and proposed a theory to obtain optimum transmission line length to minimize the reversed currents by cancelling those components. The reversed current is analyzed as being simply absorbed into the terminal resistance in the conventional analysis. In the proposed analysis, however, they are designed to be cancelled by each other with opposite phase by the optimal length of the transmission lint Circuit simulation and implementation using pHEMT transistor were performed to validate the proposed theory with the cutoff frequency of 3.6 GHz. From the measurement, maximum gain of 14.5dB and minimum gain of 12.3dB were achieved In the operation band. Moreover, measured efficiency of the proposed distributed amplifier is 25.6% at 3 GHz, which is 7.6%, higher than the conventional distributed amplifier. Measured output power Is about 10.9dBm, achieving 1.7dB higher output power than the conventional one. Those improvement is thought to be based on the cancellation of refersed current.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.685-690
• /
• 2013

This paper has proposed a multi-channel and wide gain-range baseband circuit blocks for the IEEE 802.15.4g MR-OFDM SUN systems. The proposed baseband circuit blocks consist of two negative-feedback VGAs, an active-RC 5th-order chebyshev low-pass-filter, and a DC-offset cancellation circuit. The proposed baseband circuit blocks provide 1 dB cut-off frequencies of 100 kHz, 200 kHz, 400 kHz, and 600 kHz respectively, and achieve a wide gain-range of +7 dB~+84 dB with 1 dB step. In addition, a DC-offset cancellation circuit has been adopted to mitigate DC-offset problems in direct-conversion receiver. Simulation results show a maximum input differential voltage of $1.5V_{pp}$ and noise figure of 42 dB and 37.6 dB at 5 kHz and 500 kHz, respectively. The proposed I-and Q-path baseband circuits have been implemented in $0.18-{\mu}m$ CMOS technology and consume 17 mW from a 1.8 V supply voltage.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.2
• /
• pp.67-72
• /
• 2010

In this study, the impact on the circulating water system has been analyzed due to an installation of helical turbine to develop hydro-kinetic energy at the discharge channel of the power plant. Numerical simulations of velocity and pressure variations have been performed when one set of $3.6\;m\;{\times}\;1.5\;m$ sized helical turbine is installed at the outlet of discharge culvert. In case of mean sea level, change of downstream water surface elevation does not affect upstream elevation of the weir because its propagation is blocked by the seal well weir. However in case of highest high water level, change of downstream elevation affects upstream elevation because flow pattern in discharge culvert becomes the full pipe flow with submerged weir. Although an unstable pressure change occurs in upstream of the weir during the intial 10 minutes after beginning of the discharge, it becomes stable after that time. In addition, a rise of water surface elevation by 0.2 m is observed but it is concluded that it hardly affects the safety of circulating water pump (CWP) although its required power is increased more or less. Therefore, the increase of required power of CWP needs to be considered for evaluation of the helical turbine applicability.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.3
• /
• pp.132-137
• /
• 2001

Recently, the demand for notebook PC with lithium ion batteries has steadily increased and consumers require them to adopt a SBP(smart battery pack) able to predict the remaining capacity and the run time of batteries precisely. The SBP is composed of a protection If, by which safety of lithium ion batteries is maintained against overcharge, overdischarge and overcurrent, and a smart IC, which calculates the remaining capacity and the remaining run time. The protection IC shut abmormal current down by using overcharge/overdischarge FET. A SBS(smart battery system) is composed of a system host, a smart battery and a smart battery charger. The smart ICs for SBP will be required to provide a low cost, low current consumption and small size. There will need to develop a microcomputer control type IC and an optimum algorism which is able to predict the residual capacity and the residual run time precisely. SBS will apply to many kinds of industry fields such as an electric bicycle, an electric vehicle, a load levelling and a military.

• Journal of Sensor Science and Technology
• /
• v.5 no.6
• /
• pp.51-59
• /
• 1996

A flow sensor has been fabricated by preparing thin film Pt-heater and Bi-Sb thermocouples array on 150 nm-$Si_{3}N_{4}$/300 nm-$SiO_{2}$/150 nm-$Si_{3}N_{4}$ dielectric diaphragm which has low thermal conductivity and balanced stress with silicon substrate for the purpose of improving the thermal isolation between heater and silicon substrate. Pt-heater showed nonlinear I-V characteristics due to the thermal isolation effect of the diaphragm. Its temperature coefficient of resistance was about $0.00378\;/^{\circ}C$ and Seebeck coefficient of Bi-Sb thermocouple was about $97\;{\mu}V/K$. The sensor showed that thermoelectric voltage decreased as thermal conductivity of gas increased, and flow sensitivity increased as heater voltage increased or as the distance between heater and thermocouple decreased. When heater voltage was about 2.5 V, $N_{2}$-flow sensitivity and thermal response time of the sensor were about $1.27\;mV{\cdot}(sccm)^{-1/2}$ and 0.13 sec., respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.279-279
• /
• 2007

비휘발성 메모리 Fe-RAM은 빠른 정보처리 속도와 전원공급이 차단되었을 때도 계속 정보를 유지할 수 있는 비휘발성 특징과 더불어 저전압, 저전력 구동의 장점이 있어서, 차세대 메모리로 많은 주목을 받고 있다. FeRAM에 사용되는 강유전체는 주로 Pb(Zr,Ti)$O_3$가 적용되었는데, 최근에는 비납계 강유전체의 연구도 활발히 이루어지고 있다. 이러한 비납계 강유전체 중에서 가장 특성이 우수한 물질은 $(Bi,La)_4Ti_3O_{12}$ (BLT) 이다. 그런데 BLT는 결정 방향에 따른 강한 이방성의 강유전 특성을 나타내기 때문에 BLT 박막을 이용하여 Fe-RAM 소자 등을 제작하기 위해서는 결정의 방향성을 세심하게 제어하는 것이 매우 중요하다. 지금까지 연구된 BLT 박막의 방향성 조절결과를 보면, BLT 박막을 스핀 코팅 법 (spin coating method)으로 증착하고, 핵생성 열처리 단계를 조절하여 무작위 방향성을 갖는 박막을 제조하는 방법이 일반적이었다. 그런데 이러한 스핀 코팅법에서의 핵생성 단계의 제어는 공정 조건 확보가 너무 어려운 단점이 있다. 이러한 어려움을 극복할 수 있는 대안은 스퍼터링 증착법(sputtering deposition method), PLD (pulsed laser deposition)법 등과 같은 PVD (physical vapor deposition) 법의 증착방법을 적용하는 것이다. PVD 법으로 증착하는 경우에는 이미 박막 내에 무수한 결정핵이 존재하기 때문에 핵생성 단계가 필요가 없게 된다. PVD 증착법의 적용을 위해서는 타겟의 제조 및 평가 실험이 선행되어야 한다. 그런데 벌크 BLT 재료의 소결공정 조건과 전기적 특성에 관한 연구 결과는 거의 발표가 되지 않고 있다. 본 실험에서는 $Bi_2O_3,\;TiO_2,\;La_2O_3,\;Nb_2O_5\;and\;Al_2O_3$ 분말들을 이용하여 최적의 조성을 구하기 위하여 $Nb^{+5}$ 와 $Al^{+3}$을 $Ti^{+4}$ 자리에 소량 치환시켜 제조하였다. 혼합된 분말을 하소 후 pellet 형태로 성형하여 소결을 실시하였다. 시편을 1mm 두께로 연마하고, 양면에 silver 전극을 인쇄하여 전기적 특성을 측정하였다. 측정결과 $Ti^{+4}$ 자리에 $Nb^{+5}$를 치환하여 제조한 시편에서 $2P_r{\sim}31\;{\mu}c/cm^2$정도의 매우 우수한 특성을 얻었다.