• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.133-144
• /
• 1999

To fine seam annealer capacity of through thickness seam annealing in terms of through thickness microstructure change with increased toughness and elongation leaving heat trace on it, high strength steel pipes of ERW with different thickness were tested in different seam annealing temperature measured on the outer surface of pipes. Annealing temperature and microstructure of the weld seam were changed through applied seam annealing condition. Toughness and tensile test with hardness and microstructure analysis were done on the annealed weld seam to fine its characteristics as a primary step and annealing characteristics according to different seam annealing condition. Through a study of annealed ERW weld seam characteristics and seam annealing technology, amount of electric power should apply in decreased manner to arranged inductors of annealer in the order of 1st, 2nd, 3rd, so on for proper seam annealing. For example of 15.4mm thick and 610mm outside diameter pipe, applied power for proper seam annealing is 600 -650kw at 1st inductor, 450 - 500kw at 2nd inductor, 200-250 kw at 3rd inductor of annealer during 10 - 12M/minute moving speed of pipe. Also, the penetration depth of heat trace along the thickness direction of weld during seam annealing can be estimated through the equation 17mm/kv$\times$voltage(kv) with the microstructure and hardness analysis of thick weld seam as well as study of seam annealing and comparison of cooling condition to CCT diagram of low carbon high strength steel. From this result, the difference between the technological applicability of full annealing condition based on phase diagram and full penetration of heat trace based on CCT diagram along the thickness of weld seam is discussed.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.281-291
• /
• 1995

The objective of this work is to obtain the experimental data for the heat transfer processes occurring both on the inside and outside surfaces of containment steel wall with dry and wet outer surface conditions in the passive containment cooling system. The test model represented a 60$^{\circ}$ section of a containment vessel based on the AP 600 geometry. Major linear dimensions of the test model ore reduced tv a factor of ten. To simulate the decay heat a steam generator heated by electricity was placed in the test model. The maximum heat flux was 8.91 kW/$m^2$. Two types of tests were performed. The one was the tort on the natural convection of air without water film flow. The other was the evaporative heat transfer test with the falling water film flow and natural air draft. no test result shooed that the heat transfer capability by the natural convection from the containment to the air without oater film flow was limited at about 1.48 kW/$m^2$ heat flux. It was found that the heat removal capability was remarkably enhanced in the tests with the waster film flow and air draft. The obtained heat transfer data ore compared with the existing correlations.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.30 no.3
• /
• pp.257-266
• /
• 2010

This study was carried out to investigate the effect of feeding whole crop barley silage (WBS) on the growth performance, gain, feed requirement, carcass grade and beef quality of Hanwoo steers in 1999 to 2001. Twenty one steers were allocated, and divided into three treatment groups which fed rice straw only (control), WBS only, and fresh rice straw silage plus WBS during overall period ad libitum. Concentrates were fed at 1.5% level of live-body weight during growing stages, 4~12 months of age, at 1.8% level of live-body weight during early fattening stages, 13~18 months of age, and ad libitum after late fattening stages, 19~27months of age. The production yields of WBS were 17,135 kg as a silage, and 6,011 kg as a dry matter per ha, and the quality of WBS was 2~3 grade, while that of rice straw silage was 4grade. The daily gain with feeding of WBS (0.70 kg) during experimental period was higher than that of control group (0.65 kg), and the concentrate requirement (7.31 kg) per kg gain in WBS was lower than that of control (8.95 kg). The effects of gain and feed efficiency were very distinct during growing stage. i.e., the daily gain of WBS (0.84 kg) was increased by 65% compared to control (0.51 kg), and the concentrate requirement (4.16 kg) per kg gain in feeding of WBS was decreased by 35%, compared to control (6.39 kg). Meat quality with WBS was higher than that of control. Frequency rate of 1 and/or $1^+$ grade, and marbling score of feeding of WBS were 62.5% and 4.38, while those of control were 37.5% and 2.75, respectively. The results of the sensory evaluation showed that Hanwoo beef fed with WBS were better than that of control. In conclusion, feeding of WBS was desirable to improve daily gain, reduction of concentrates, feed efficiency and meat quality of Hanwoo steers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.229-229
• /
• 2010

본 실험에서는 $CuInSe_2$, 3원물질을 화학량론적 조성비가 되도록 박막을 제조하기 위해 각 단위원소를 원자비에 맞춰 전자선가열 진공증착기를 사용하여 Cu, In, Se 순으로 증착하였다. $10^{-3}$torr 이상의 진공석영관에서 열처리와 동시에 Selenization을 통해 제작된 $CuInSe_2$박막은 열처리온도 $250^{\circ}C$에서는 $Cu_xSe$, CuSe등의 2차상들이 나타나다가 $450^{\circ}C$이상의 고온에서 $CuInSe_2$ 단일상을 형성하였다. 이로부터 진공중에서 반응을 시켰을 때, 더 낮은 온도에서 반응이 일어나고 열역학적으로 보다 안정한 소수의 화합물들이 쉽게 형성됨을 확인할 수 있었다. 특히 $250^{\circ}C$에서는 Sphalerite 구조를 가지다가 $350^{\circ}C$이상의 온도에서 Selenization하였을 때 Chalcopyrite 구조를 가졌다. 박막이 두꺼워지면서 결정립의 크기가 커지고 응력이 작아지는 특성을 보였다. 에너지 밴드갭은($E_g$)은 Cu/In 성분비율이 클수록 작은값을 보였으며, 결절립크기가 증대되므로 결국 흡수계수가 낮아짐을 알 수 있다. 또한 두께가 증가할수록 전반적으로 흡수계수가 증가하였고 Cu/In의 성분비율이 0.97일 때 기초흡수파장은 1,169nm이고 에너지밴드갭은 1.06eV이었으며, 두께 $1.5{\mu}m$이상일 때 전반적으로 양호한 상태의 p-type $CuInSe_2$ 박막을 제작 하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.301-307
• /
• 2002

Direct bonded SOI wafer pairs with $Si ll SiO_2/Si_3N_4 ll Si$ the heterogeneous insulating layers of SiO$_2$-Si$_3$N$_4$are able to apply to the micropumps and MEMS applications. Direct bonding should be executed at low temperature to avoid the warpage of the wafer pairs and inter-diffusion of materials at the interface. 10 cm diameter 2000 ${\AA}-SiO_2/Si(100}$ and 560 $\AA$- ${\AA}-Si_3N_4/Si(100}$ wafers were prepared, and wet cleaned to activate the surface as hydrophilic and hydrophobic states, respectively. Cleaned wafers were pre- mated with facing the mirror planes by a specially designed aligner in class-100 clean room immediately. We employed a heat treatment equipment so called fast linear annealing(FLA) with a halogen lamp to enhance the bonding of pre mated wafers We kept the scan velocity of 0.08 mm/sec, which implied bonding process time of 125 sec/wafer pairs, by varying the heat input at the range of 320~550 W. We measured the bonding area by using the infrared camera and the bonding strength by the razor blade clack opening method, respective1y. It was confirmed that the bonding area was between 80% and to 95% as FLA heat input increased. The bonding strength became the equal of $1000^{\circ}C$ heat treated $Si ll SiO_2/Si_3N_4 ll Si$ pair by an electric furnace. Bonding strength increased to 2500 mJ/$\textrm{m}^2$as heat input increased, which is identical value of annealing at $1000^{\circ}C$-2 hr with an electric furnace. Our results implies that we obtained the enough bonding strength using the FLA, in less process time of 125 seconds and at lowed annealing temperature of $400^{\circ}C$, comparing with the conventional electric furnace annealing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.199-199
• /
• 2013

최근 단파장 광전 소자와 고출력 고주파 전자 소자에 대한 수요 때문에 넓은 밴드갭 에너지를 갖는 반도체에 관심이 많다. 이중에서, ZnO는 우수한 화학 및 역학적 안정성, 수소 플라즈마 내구성과 저가 제조의 장점 때문에 광전자 소자 개발 분야에 적합한 산화물 투명 전극으로 관심을 끌고 있다. 불순물이 도핑되지 않은 ZnO는 본질적으로 산소 빈자리 (vacancy)와 아연 격자틈새 (interstitial)와 같은 자체의 결함으로 말미암아 n형의 극성을 갖기 때문에, 반도체 소자로 응용하기 위해서는 도핑 운반자의 농도와 전도성을 제어하는 것이 필요하다. 본 연구에서는 박막 제조시 제어성, 안정성과 용이하게 성장이 가능한 졸겔 (sol-gel) 방법을 사용하여 사파이어와 석영 기판 위에 Cu가 도핑된 ZnO 박막을 성장시켰으며, 그것의 구조, 표면 형상, 평균 투과율, 광학 밴드갭 에너지를 계산하였다. 특히, Cu의 몰 비를 0, 0.01, 0.03, 0.05, 0.07, 0.1 mol로 변화시키면서 ZnO:Cu 박막을 성장시켰다. ZnO:Cu 졸은 zinc acetate dihydrate, 2-methoxyethanol (용매), momoethanolamine (MEA, 안정제)을 사용하여 제조하였다. 상온에서 2-methoxyethanol과 MEA가 혼합된 용액에 zinc acetate dihydrate (Zn)을 용해시켰다. 이때 MEA와 Zn의 몰 비는 1로 유지하였다. 이 용액을 $60^{\circ}C$ 가열판 (hot plate)에서 24 h 동안 자석으로 휘젓으며 혼합하여 맑고 균일한 용액을 얻었다. 이 용액을 3000 rpm 속도로 회전하는 스핀 코터기의 상부에 장착된 사파이어와 석영 기판 위에 주사기 (syringe)를 사용하여 한 방울 떨어뜨려 30 s 동안 스핀한 다음에, 용매를 증발시키고 유기물 찌꺼기를 제거하기 위하여 $300^{\circ}C$에서 10분 동안 건조시킨다. 기판 위에 코팅하는 작업에서 부터 건조 작업까지를 10회 반복한 다음에, 1 h 동안 전기로에 장입하여 석영 기판 위에 증착된 시료는 $550^{\circ}C$에서, 사파이어 기판은 $700^{\circ}C$에서 열처리를 수행하였다. Cu의 몰 비 0, 0.01, 0.03, 0.05, 0.07, 1로 성장된 ZnO:Cu 박막에 대한 x선 회절 분석의 결과에 의하면, 모든 ZnO:Cu 박막의 경우에 관측된 34.3o의 피크는 ZnO (002) 면에서 발생된 회절 패턴을 나타낸다. 이것은 JCPDS #80-0075에 제시된 회절상과 일치하였으며, ZnO:Cu 박막이 기판에 수직인 c-축을 따라 우선 배향됨을 나타낸다. 사파이어 기판 위에 증착된 박막의 경우에, Cu의 몰 비가 점점 증가함에 따라(002)면 회절 피크의 세기는 전반적으로 증가하여 0.07 mol에서 최대를 나타내었으나, 석영 기판 위에 증착된 박막의 경우에는 0.05 mol에서 최대를 보였다. 외선-가시광 분광계를 사용하여 서로 다른 Cu의 몰 비로 성장된 ZnO:Cu 박막에서 광학 흡수율 (absorbance) 스펙트럼을 측정하였으며, 이 데이터를 사용하여 평균 투과율을 계산한 결과, 투과율은 Cu의 몰 비에 따라 현저한 차이를 나타내었다. Cu의 몰 비가 0.07 mol일 때 평균 투과율은 80%로 가장 높았으며, 0.03 mol에서는 30%로 최소이었다. 광학밴드갭 에너지는 Tauc 모델을 사용하여 계산하였고, 결정 입자의 형상과 크기와의 상관 관계를 조사하였다.

• Journal of Animal Science and Technology
• /
• v.47 no.4
• /
• pp.593-606
• /
• 2005

Present study was conducted to investigate the optimal feeding levels for producing the high quality meat on the basis of the information deriving from the comparison of the growth performance and carcass characteristics among breeds(Holstein vs F1, Holstein♀×Hanwoo♂), sex(steer vs heifer) and interaction between breed and sex. Thirty two animals on 4 treatments(i.e. eight head each) were used for 540 days from seven to 24 months of age. The results obtained are summarized as follows; the range of average daily gains was 0.733 to 1.018, 0.994 to 1.255, 0.947 to 1.259 and 0.736 to 0.824kg for the growing, the early-fattening, the mid- fattening and the finishing periods, respectively. The range of average daily gains for the entire period was 0.882 to 1.061kg. The gains were higher for Holstein(7.3%) and the steers(10.5%) than F1 and the heifers, respectively. Concentrates and total digestible nutrients intakes per kg gain were higher for Holstein and the heifers than F1 and the steers, respectively. These findings may indicate that feed utilization is higher for Holstein than F1, and higher for the steers than the heifers. In carcass characteristics, back fat thickness was thicker for Holstein than F1, and rib-eye area was smaller for Holstein than F1. The rib-eye area per kg carcass weight was larger for F1 and the heifers than Holstein and the steers, respectively. Meat color was better for Holstein than F1, but the sex distinction did not show any differences. In physicochemical properties of longissimus dorsi, shear force, cooking loss, water holding capacity and the panel test scores of juiciness, tenderness and flavor for F1 and the heifers were better than those for Holstein and the steers, respectively. According to the above results, we may conclude that F1 and heifers rather than Holstein and steers are recommended for high quality meat production. In steers and heifers of Holstein and F1, the optimal feeding levels may be 1.9% of apparent body weight for concentrates and 25% of concentrates intake for rice straw.

• Journal of Life Science
• /
• v.17 no.4 s.84
• /
• pp.540-545
• /
• 2007

The purpose of this research is to study the effects of feeding dietary citrus byproducts TMR (total mixed ration) on physicochemical properties and sensory characteristics of Korean native beef loin (KNBL). The samples for experiment consist of the KNBL not fed with citrus byproducts (TMR-0) and the KNBL fed with citrus byproducts during fattening period (TMR-1). The control (TMR-0) KNBL was fed by general practical feeding (roughages and concentrates were fed separately), while the TMR-1 KNBL was fed by the same as TMR-0 until 17 months yearling but was fed by citrus byproducts feeding for 10 months after that. The $L^*(lightness),\;a^*(redness)\;and\;b^*(yellowness)$ value were not significantly different between TMR-0 and TMR-1. The pH of TMR-1 was lower than that of TMR-0 (p<0.05), the VBN content, TBARS value and EDA were not significantly different between TMR-0 and TMR-1. The water holding capacity, frozen loss and cooking loss were not significantly different between TMR-0 and TMR-1, but thawing loss of TMR-0 was higher than that of TMR-1 (p<0.05). The hardness of TMR-0 was higher than that of TMR-1, and the springiness of TMR-1 was higher than that of TMR-0 (p<0.05), but the cohesiveness, gumminess, chewiness and shear force were not significantly different between TMR-0 and TMR-1. The pH and VBN content during storage were not significantly different between TMR-0 and TMR-1, but the TBARS value of TMR-1 stored during 4 weeks was lower than that of TMR-0 (p<0.05). In case of sensory score, the color and aroma of raw meat, and the taste, juiciness and palatability of cooked meat were not significantly different between TMR-0 and TMR-1. But the flavor and tenderness of TMR-1 were superior than those of TMR-0 (p<0.05)

• Journal of the Society of Disaster Information
• /
• v.10 no.4
• /
• pp.583-597
• /
• 2014

Fire caused by heater has various causes as many as the types of heater. also, lots of damage of human life and property loss are caused, since annually continuous fire accident by heater in traditional market is frequently occurring. There are not many cases of fire due to heater in most of residential facilities such as general house, apartments, etc., because they are supplied with heating boiler, however the restaurant, store and office of the market, sports center, factory, workplace, etc. still use heater, e.g. oilstove, electric heater, etc., so that they are exposed to fire hazard. Also, when investigating the number of fire due to heater, it was analyzed to occur in order of home boiler, charcoal stove, oilstove, gas heater/stove, electric stove/heater, the number of fire per human life damage was analyzed in order of gas heater/stove, oil heater/stove, electric heater/stove, briquette/coal heater. Also, gas and oil related heater were analyzed to have low frequency, however, with high fire intensity. Therefore, this research aimed at considering more scientific fire inspection and identification approach by reenacting and reviewing fire outbreak possibility caused by combustibles' contact and conductivity under the normal condition and abnormal condition in respect of ignition hazard, i.e. minimum ignition temperature, carbonization degree and heat flux along with it, due to oilstove and electric stove, which are still frequently used in public use facility, traditional market, and, of which actual fire occurrence is the most frequent. As the result of reenact test, ignition hazard appeared very small, as long as enough heat storage condition is not made in both test objects(oilstove/electric stove), however carbonization condition was analyzed to be proceeded per each part respectively. Eventually, transition to fire is the ignition due to heat storage, so that it was analyzed to ignite when minimum heat storage temperature condition of fire place is over $500^{\circ}C$. Particularly, in case of quartz pipe, the heating element of electric stove, it is rapidly heated over the temperature of $600^{\circ}C$ within the shortest time(10sec), so that the heat flux of this appears 6.26kW/m2, which was analyzed to result in damage of thermal PVC cable and second-degree burn in human body. Also, the researcher recognized that the temperature change along with Geometric View Factor and Fire Load, which display decrease of heat, are also important variables to be considered, along with distance change besides temperature condition. Therefore, the researcher considers that a manual of careful fire inspection and identification on this is necessary, also, expects that scientific and rational efforts of this research can contribute to establish manual composition and theoretical basis on henceforth fire inspection and identification.

• Resources Recycling
• /
• v.22 no.2
• /
• pp.22-28
• /
• 2013

In the present study, the possibility of recovering and recycling the silicon carbide(SiC) from a silicon sludge by removing Fe and Si impurities was investigated. Si and SiC were separated from the silicon sludge using centrifugation. The separated SiC concentrate consisted of Fe, Si and SiC, in which Fe and Si were removed to recover the pure SiC. Leaching with acid/alkali solution was compared with the vapor-phase chlorination. The Fe concentration removed in the SiC was 49 ppm, and it was separated by leaching with 1 M HCl solution at $80^{\circ}C$ for 1 h. The Si concentration removed in the SiC was 860 ppm, and it was separated by leaching with 1M NaOH solution at $50^{\circ}C$ for 1 h. The SiC concentrate was chlorinated in a tubular reactor, 2.4 cm in diameter and 32 cm in length. The boat filled with SiC concentrate was located at the midpoint of the alumina tube, then, the chlorine and nitrogen gas mixture was introduced. The Fe and Si concentration removed in the SiC were 48 ppm and 405 ppm, respectively, at $500^{\circ}C$ reactor temperature, 4 h reaction time, 300 cc/min gas flow rate, and 10% $Cl_2$ gas mole fraction.