• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.483-491
• /
• 2001

The recovery and recrystallization behavior of cold-rolled Zr-based alloys during isothermal annealing at temperatures from $575^{\circ}C$ to $650^{\circ}C$ was studied by thermoelectric power and Vickers microhardness measurement. The recovery and recrystallization resulted in the increase of TEP doe to the extinction of lattice defect, vacancy, dislocation and stacking fault during isothermal annealing after cold- rolling. The completion of recrystallization could be determined much clearly by TEP behavior than by microhardness change in Zr-based alloys. Especially, the recovery and recrystallization were classified separately by TEP behavior in Zr-0.4Nb-xSn alloys. From the analysis of TEP behavior and microhardness, the addition of Sn caused to form the interaction between stain field and dislocation, which resulted in the delay of recovery in Zr-based alloys. The precipitation due the addition of Nb suppressed the grain growth after recrystallization effectively in Zr-based alloys.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.1
• /
• pp.33-40
• /
• 1998

The composite SiO$_2$/Si$_3$N$_4$/SiO$_2$(ONO) film formed by oxidation on nitride film has been widely studied as DRAM stacked capacitor multi-dielectric films. Load lock(L/L) LPCVD system by HF cleaning is used to improve electrical capacitance and to scale down of effective thickness for memory device, but is brings a new problem. Nitride film deposited using HF cleaning shows selective deposition on poly silicon and oxide regions of capacitor. This problem is avoidable by carpeting chemical oxide using $H_2O$$_2$cleaning before nitride deposition. In this paper, we study the limit of nitride thickness for abnormal oxidation and the initial deposition time for nitride deposition dependent on underlayer materials. We proposed an advanced fabrication process for stacked capacitor in order to avoid selective deposition problem and show the usefulness of nitride deposition using L/L LPCVD system by $H_2O$$_2$cleaning. The natural oxide thickness on polysilicon monitor after HF and $H_2O$$_2$cleaning are measured 3~4$\AA$, respectively. Two substrate materials have the different initial nitride deposition times. The initial deposition time for polysilicon is nearly zero, but initial deposition time for oxide is about 60seconds. However the deposition rate is constant after initial deposition time. The limit of nitride thickness for abnormal oxidation under the HF and $H_2O$$_2$cleaning method are 60$\AA$, 48$\AA$, respectively. The results obtained in this study are useful for developing ultra thin nitride fabrication of ONO scaling and for avoiding abnormal oxidation in stacked capacitor application.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.352-356
• /
• 2011

Transparent conducting oxide films like ITO/Au/ITO and AZO/Au/AZO were fabricated with a sputter at a low-temperature of less then $70^{\circ}C$ and their crystallization and opto-electrical properties were studied. X-ray diffractiometry showed that single-ITO layer was amorphous, whereas, ITO of ITO/Au/ITO multi-layer was crystal. The ITO crystallization and its orientation depended on Au crystallization. Surface roughness of the ITO-multi-layers were in the range of 29-88% of that of ITO-single layer. ITO on amorphous gold layer had more rough surface than ITO on crystal gold. The gold layer between ITO improved electrical conductivity. Carrier density, mobility, resistivity and sheet resistance of ITO-single layer were $2.3{\times}10^{19}/cm^3$, $85{\times}cm^2$/Vs, $31{\times}10^{-4}{\Omega}cm$, and $310{\times}{\Omega}/cm^2$, respectively. Those of ITO/Au/ITO-multi-layers depended on Au-interlayer-thickness, which were in the range of $3.6{\times}10^{19}{\sim}4.2{\times}10^{21}/cm^3$, $43{\sim}85cm^2$/Vs, $0.17{\times}10^{-4}{\sim}25{\times}10^{-4}{\Omega}cm$, and $1.7{\sim}20{\times}{\Omega}/cm^2$, respectively. The sheet resistances of the single-layer ITO and the multi-layer ITO were 310 and $2.7{\sim}21{\Omega}/cm^2$, respectively. That of AZO/Au/AZO was $8.6{\Omega}/cm^2$, which was better than the single-layer ITO.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.775-783
• /
• 2012

The effect of thermal annealing on the in-situ growth characteristics of intermetallics (IMCs) and the mechanical strength of Cu pillar/Sn-3.5Ag microbumps are systematically investigated. The $Cu_6Sn_5$ phase formed at the Cu/solder interface right after bonding and grew with increased annealing time, while the $Cu_3Sn$ phase formed at the $Cu/Cu_6Sn_5$ interface and grew with increased annealing time. IMC growth followed a linear relationship with the square root of the annealing time due to a diffusion-controlled mechanism. The shear strength measured by the die shear test monotonically increased with annealing time. It then changed the slope with further annealing, which correlated with the change in fracture modes from ductile to brittle at a critical transition time. This is ascribed not only to the increasing thickness of brittle IMCs but also to the decreasing thickness of the solder, as there exists a critical annealing time for a fracture mode transition in our thin solder-capped Cu pillar microbump structures.

• Prospectives of Industrial Chemistry
• /
• v.24 no.5
• /
• pp.1-14
• /
• 2021

유무기 하이브리드 금속-할라이드계 페로브스카이트(organic-inorganic metal halide perovskite) 페로브스카이트 반도체 소재는 광전자 소자와 소재 연구에 새로운 연구 흐름을 만들고 있다. 태양전지 성능이 불과 과거 몇 년 사이의 짧은 연구 기간에도 불구하고, 광-전 변환 소자 중에서도 단일 소자와 적층 소자(tandem)에서 높은 광-전 변환 효율을 나타내기 때문이다. 이러한 급격한 연구 성과와 성장에도 불구하고, 페로브스카이트 소재의 다양한 광전자 특성의 평가와 결과에 대한 논의가 필요한 상황이다. 특히 내부 이온 이동이 광전자 원거리 이동 특성 평가와 해석에 영향을 주는 경우, 페로브스카이트 소재를 기반으로 한 다양한 광전자 소자의 성능 향상과 해석에 여전히 모호함을 준다. 달리 얘기하면, 이 소재의 기초 특성을 이해하고자 적용하는 다양한 기존 특성 평가 분석법의 활용과 해석에도 복잡한 영향을 미치고 있다고 할 수 있다. 이러한 페로브스카이트 소재 내에서 광전자 원거리 이동을 측정하는 새로운 방법을 소개하고자 한다. 첫 번째 방법으로, Quasi-steady 상태에서 광전도도를 전기적 특성으로 측정하고, 광조사 하에 투과 및 반사를 광학적으로 측정하여, 전도도와 광전자 밀도를 동시에 평가하는 방법으로, photo-induced transmission and reflection (PITR) 분광분석법이다. 이 분광분석법은 실제 소자의 구동조건을 구현한 상태에서 광전자의 원거리 이동에서 발생하는 광전자 밀도 변화를 반영한 광전자 이동도 특성 평가라는 장점을 가지고 있다. 두 번째 방법으로, 기존의 연속 전압 인가 방법 대신 펄스형 전압 인가 방식을 도입하는 방법으로, pulsed voltage space charge limited current (PV-SCLC) 분석법이다. 이는 펄스형 전압 인가 방법으로 이온의 이동을 최소화하여, 전류-전압 측정에서 히스테리시스가 없고 측정결과의 재현성과 신뢰도가 매우 높은 장점이 있다.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.395-403
• /
• 2006

It is known that $MgAl_2O_4$ has higher resistance to moisture than MgO, in humid ambient MgO is chemically unstable. It reacts very easily with moisture in the air. In this study, the characteristic of $MgAl_2O_4$ and $MgAl_2O_4/MgO$ layers as dielectric protection layers for AC- PDP (Plasma Display Panel) have been investigated and analysed in comparison for conventional MgO layers. MgO and $MgAl_2O_4$ films both with a thickness of $1000\AA$ and $MgAl_2O_4/MgO$ film with a thickness of $200/800\AA$ were grown on the Cu substrates using the electron beam evaporation. $1000\AA$ thick aluminium layers were deposited on the protective layers in order to avoid the charging effect of $Ga^+$ ion beam while the focused ion beam(FIB) is being used. We obtained sputtering yieds for the MgO, $MgAl_2O_4$ and $MgAl_2O_4/MgO$ films using the FIB system. $MgAl_2O_4/MgO$ protective layers have been found th show $24{\sim}30%$ lower sputtering yield values from 0.244 up to 0.357 than MgO layers with the values from 0.364 up to 0.449 for irradiated $Ga^+$ ion beam with energies ranged from 10 kV to 14 kV. And $MgAl_2O_4$ layers have been found to show lowest sputtering yield values from 0.88 up to 0.109. Secondary electron emission coefficient(g) using the ${\gamma}$- FIB. $MgAl_2O_4/MgO$ and MgO have been found to have similar g values from 0.09 up to 0.12 for indicated $Ne^+$ ion with energies ranged from 50 V to 200 V. Observed images for the surfaces of MgO and $MgAl_2O_4/MgO$ protective layers, after discharge degradation process for 72 hours by SEM and AFM. It is found that $MgAl_2O_4/MgO$ protective layer has superior hardness and degradation resistance properties to MgO protective layer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.305-310
• /
• 2009

$TiO_2$ thin films consisting of positively charged poly (diallyldimethylammonium chloride) (PDDA) and negatively charged titanium (IV) bis (ammonium lactato) dihydroxide (TALH) were successfully fabricated on a poly (methyl methacrylate) (PMMA) by layer-by-layer (LBL) self-assembly method. By the measurement of quartz crystal microbalance (QCM), it was found that as the solution pH of TALH decreased, the deposition volume of TALH increased and the thickness of (PDDA/TALH) thin film coated on the surface of PMMA particles increased. The PMMA particles coated with the coating sequence of (PDDA/TALH)n showed the variation of color changes as a function of the number of bilayer. The number of bilayer (n) of (PDDA/TALH) thin films was 10 and 20, the values of $a^*$ and $b^*$ decreased from those of PMMA particles without coating films and the color changes was shifted to green and blue direction in the $a^*$, $b^*$ chromaticity diagram. And then, the number of n increased to 30 and 40, the values of $a^*$ and $b^*$ increased and the color changes was shifted to red and yellow direction, respectively. Finally the PMMA particles coated with $(PDDA/TALH)_{50}$ thin film showed a little same value of $a^*$ and $b^*$ with the PMMA particles without (PDDA/TALH) thin film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.5
• /
• pp.256-261
• /
• 2009

Hydrophilic and transparent $TiO_2$ thin film was fabricated by sol-gel method and the properties of contact angle, surface morphology, and transmittance were measured. In addition, surfactant Tween 80 was used for increasing the hydrophilic property of thin film. When the contents of Tween 80 in $TiO_2$ solution was 0, 10, 30, 50wt%, the contact angles of $TiO_2$ thin film were $41.4^{\circ}$, $18.2^{\circ}$, $16.0^{\circ}$, $13.2^{\circ}$, respectively. Fabricated $TiO_2$ thin film showed the photocatalytic property that decomposed methylene blue and decreased the absorbance of solution after UV irradiation. $TiO_2$ thin films fabricated with the solution of 30 wt% Tween 80 were deposited on glass (bare), antimony tin oxide (ATO), fluorine tin oxide (FTO), indium tin oxide (ITO) coated glass substrates, and the contact angle and transmittance of thin film was measured. The contact angles of thin films deposited on four substrates were $16.2\sim27.1^{\circ}$ and was decreased to the range of $13.2\sim17.6^{\circ}$ after UV irradiation, Especially, the thin films coated on ATO and FTO glass substrate showed high transmittance of 74.6% in visible range, respectively, and low transmittance of 54.2% and 40.4% in infrared range, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.255-260
• /
• 2023

As demanding the detection of explosive molecules, it is required to develop rapidly and precisely responsive sensors with ultra-high sensitivity. Since two-dimensional semiconductors have an atomically thin body nature where mobile carriers accumulate, the abrupt modulation carrier in the thin body channel can be expected. To investigate the effectiveness of WSe₂ semiconductor materials as a detection material for TNT (Trinitrotoluene) explosives, WSe₂ was synthesized using thermal chemical vapor deposition, and afterward, WSe₂ FETs (Field Effect Transistors) were fabricated using standard photo-lithograph processes. Raman Spectrum and FT-IR (Fourier-transform infrared) spectroscopy reveal that the adsorption of TNT molecules induces the structural transition of WSe₂ crystalline. The electrical properties before and after adsorption of TNT molecules on the WSe₂ surface were compared; as -50 V was applied as the back gate bias, 0.02 μA was recorded in the bare state, and the drain current increased to 0.41 μA with a dropping 0.6% (w/v) TNT while maintaining the p-type behavior. Afterward, the electrical characteristics were additionally evaluated by comparing the carrier mobility, hysteresis, and on/off ratio. Consequently, the present report provides the milestone for developing ultra-sensitive sensors with rapid response and high precision.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.895-905
• /
• 1994

The solid phase crystallization behavior of undoped amorphous $Si_{1-x}Ge_{x}$ (X=O to 0.53) alloyfilms was studied by X-ray diffractometry(XRD) and transmission electron microscopy(TEM). Thefilms were deposited on thermally oxidized 5" (100) Si wafer by MBE(Mo1ecular Beam Epitaxy) at 300'C and annealed in the temperature range of $500^{\circ}C$ ~ $625^{\circ}C$. From XRD results, it was found that the thermal budget for full crystallization of the film is significantly reduced as the Ge concentration in thefilm is increased. In addition, the results also shows that pure amorphous Si film crystallizes with astrong (111) texture while the $Si_{1-x}Ge_{x}$ alloy film crystallzes with a (311) texture suggesting that the solidphase crystallization mechanism is changed by the incorporation of Ge. TEM analysis of the crystallized filmshow that the grain morphology of the pure Si is an elliptical and/or a dendrite shape with high density ofcrystalline defects in the grains while that of the $Si_{0.47}Ge_{0.53}$ alloy is more or less equiaxed shape with muchlower density of defects. From these results, we conclude that the crystallization mechanism changes fromtwin-assisted growth mode to random growth mode as the Ge cocentration is increased.ocentration is increased.