• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.247-252
• /
• 2013

In this paper, a microwave tag system of a frequency-scanning type is proposed with multi-resonators using defected ground structures. While a conventional chip-based RFID stores time-sequential codes, the proposed type achieves pure passive tags by using multi-resonant bits over a frequency range. Moreover, the resonators of the spiral defected ground structures implemented on the back side of transmission lines have advantages of the excellent bandstop characteristics as well as the bit-error avoidance by the re-radiation on normal resonators. The proposed microwave tag is designed with UWB antennas at 3~7 GHz. From the experimental results in an anechoic chamber, it has been verified of the excellent recognitions for various 5-bits identification codes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.883-892
• /
• 2005

We propose a T-shaped UWB printed monopole antenna and investigate the effect of the surface currents of the radiator and ground plane. The measured impedance bandwidth of the antenna covers the range of 3.1 to 11 GHz for a VSWR$\le$2, which satisfies the requirement of the UWB operation. From the analysis of the surface currents, the proposed antenna can be treated as two asymmetric dipoles with the included angle of 90 degrees which lie along z-direction symmetrically. It is observed that the effect of the surface currents on the radiation patterns is similar to that of the corresponding dipole. The length and width of the found plane correspond the radius and length of the dipole respectively. This approach is also valid to general printed monopole antennas. Finally, we included an antenna example having resonance at a lower frequency by tapering the edges of the ground plane and another example having a bandstop characteristic by inserting an inverted-U slot on the radiator, and explain those antennas using the surface currents.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.627-634
• /
• 2010

In this paper, a novel voltage-controlled oscillator(VCO) using the complimentary bifilar archimedean spiral resonator(CBASR) is presented for reducing the phase noise characteristic. A CBASR has compact dimension, a sharp skirt characteristic in stopband, a low insertion loss in passband, and a large coupling coefficient value, which makes a high Q value and improve the phase noise of VCO. The proposed VCO has the oscillation frequency of 2.396~2.502 GHz in the tuning voltage of 0~5 V, the output power of 7.5 dBm and phase noise of -119.16~-120.2 dBc/㎐ at the offset frequency of 100 kHz in tuning range.

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.174-179
• /
• 2004

Attenuation of conduction noise through microstrip line attached with the high lossy iron flakes-rubber composites has been investigated in GHz frequencies. Microstrip line was designed with characteristic impedance of 50 $\Omega$ and a length corresponding to the center frequency of 3 GHz. Iron flakes were fabricated by mechanical forging of spherical iron powders using an attrition mill. The fabricated microstrip line shows a ideal propagation characteristics of S$\sub$11/ < -60 dB and S$\sub$21/ = 0 dB. Attaching a noise absorbing sheet on the microstrip line, S$\sub$11/ increases to about -10 dB and S$\sub$21/ decreases to -20～-60 dB depending on the length of absorbing sheet. The calculated power loss is as high as 80% in the frequency range 2～8 GHz. It is suggested that the most critical material parameter is magnetic loss for the enhancement of noise attenuation.

• Journal of IKEEE
• /
• v.5 no.2 s.9
• /
• pp.128-135
• /
• 2001

Optical wavelength filters based on directional couplers are rigorously designed and analyzed by Modal Transmission-Line Theory (MTLT). The conventional parallel directional coupler is utilized to implement a narrow-band filter, and it takes up the coupler with tapered structure as a wide-band filter. The power transfers of TE/TM modes in narrow-band filters are maximized at ${\lambda}=1.303{\mu}m\;and\;1.1496{\mu}m$, and the optical bandwidths are then 30nm and 10nm, respectively. Furthermore, when the coupling lengths of TE/TM modes in wide-band filters operating at ${\lambda}=1.55{\mu}m$ are selected as $183{\mu}m\;and\;178{\mu}m$, those are operated as the stop-band and pass-band filters, respectively.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.99-103
• /
• 2006

A tunable wavelength filter was proposed and demonstrated by using the UV nanoimprint technique. It consists of a Bragg grating in polymer waveguides and a heating electrode. The manufacturing of the grating was substantially simplified with the introduction of a smart imprint stamp containing a waveguide pattern integrated with the grating pattern. The center wavelength of the filter was successfully tuned by taking advantage of the thermooptic effect in polymers, which was induced by supplying electrical power to the electrode. For the fabricated device, a transmission dip of ${\~}$15 dB and a 3-dB bandwidth of 0.8 nm were obtained at the Bragg wavelength of ${\~}$l560 nm. The achieved thermooptic tuning efficiency was ${\~}$0.28 nm/mW, while the center wavelength was shifted from 1560 nm to 1558 nm with the electrical power consumption of 7 mW.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.6
• /
• pp.1602-1609
• /
• 1998

In this paper, the design and implementation of the novel RF front end circuit for CDMA based PCS phone is described. This novel scheme is realized by building the power amplifier module combined with duplexer. The dielectric filters which are parts of duplexer are broken up and relocated into the module. Electromagnetic analysis for via holes and coupling between narrow transmissio lines is icluded to design a circuit. The combined moule has been minimaturized to be as small as 1.5CC. It has satisfied IS-95 requirements for linearity performances of CDMA signal at 24-dBm output power as well as played apart as a duplexer. The operating current of about 95mA has been saved owing to both rearranging dielectric filters and limiting operating point to class-B by considering real working power range of CDMA phones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7C
• /
• pp.658-666
• /
• 2007

In general, the earlier linear-phase MAXFLAT(maximally flat) lowpass FIR filters have the main disadvantage of a gain response in the half frequency band $(0{\leq}w{\leq}{\pi}/2)$ by the closed form transfer functions used in design techniques for realizing them. Moreover, most of them has existent problems as follows : ripple error in the stopband, gentle-cutoff attenuation, phase and group delay and inexact cutoff frequency response. It is due to the approximation algorithms such as Chebyshev norm and Remez exchange which are used to approach MAXFLAT and linear-phase characteristics in frequency domain. In this paper, a new mathematically closed-form transfer function is introduced for the design of MAXFLAT lowpass FIR filters which have the zero-phase and wideband-gain response. In addition, we verify that the closed-form transfer function is easily realized due to our generalized formulas derived newly by using MAXFLAT conditions including an arbitrary cutoff point. This method is, therefore, useful for "simple and quick designs". Conclusively, we propose a technique for the design of new zero-phase wideband MAXFLAT lowpass FIR filters which can achieve sharp-cutoff attenuation exceeding 250 dB almost everywhere.

• Journal of Navigation and Port Research
• /
• v.30 no.5 s.111
• /
• pp.331-334
• /
• 2006

In this paper, we designed and fabricated the lowpass filter with the wide stopband characteristics using microp- strip line. Adding the $\lambda_g/4$ open stub at the input and output ports, we developed the L-C ladder type lowpass filter using the open stub which has wide stopband characteristics. In order to reduce the entire size qf this filter, the high impedance microstrip lines were made with the meander structure. The lowpass filter was fabricated with the cutoff frequency 2.3 GHz and its measured frequency responses agree well with the simulation results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.10
• /
• pp.109-117
• /
• 2004

In this paper, a K-band local oscillator composed of a VCDRO(Voltage Controlled Dielectric Resonator Oscillator), GaAs MESFET, and Reflector type frequency doubler has been designed and fabricated. TO obtain a good phase noise performance of a VCDRO, a active device was selected with a low noise figure and a low flicker noise MESFET and a dielectric resonator was used for selecting stable and high oscillation frequency. Especially, to have a higher conversion gain than a conventional doubler as well as a good harmonic suppression performance with circuit size reduced a doubler structure was employed as the Reflector type composed of a reflector and a open stub of quarter wave length for rejecting the unwanted harmonics. The measured results of fabricated oscillator show that the output power was 5.8 dBm at center frequency 12.05 GHz and harmonic suppression -37.98 dBc, Phase noise -114 dBc at 100 KHz offset frequency, respectively, and measured results show of fabricated frequency doubler, the output power at 5.8 dBm of input power is 1.755 dBm conversion gain 1.482 dB, harmonic suppression -33.09 dBc, phase noise -98.23 dBc at 100 KHz offset frequency, respectively. This oscillator could be available to a local oscillator in K-band which used frequency doubler techniques.