• Journal of IKEEE
• /
• v.3 no.1 s.4
• /
• pp.11-21
• /
• 1999

This paper has been proposed a structure composed of FIRs and IIR filters as digital interpolation filter to integrate the off-chip analog low-pass filter of audio DAC. The passband ripple (>$0.41{\times}fs$), passband attenuation(>at$0.41{\times}fs$) and stopband attenuation(<$0.59{\times}fs$) of the ${\Delta}{\Sigma}$ modulator output using the proposed digital interpolation filter had ${\pm}0.001[dB]$, -0.0025[dB] and -75[dB], respectively. Also the inband group delay was 30.07/fs[s] and the error of group delay was 0.1672%. Also, the attenuation of stopband has been increased -20[dB] approximately at 65[kHz], out-of-band. Therefore the RC products of analog low-pass filter on chip have been decreased compared with the conventional digital interpolation filter structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.418-426
• /
• 2008

In this paper, investigations on the impedance characteristics of a DGS(Defected Ground Structure) slot in the groud plane of microstripline are presented in spectral domain and applied to the characteristic improvement of stepped impedance microstrip low pass filter(LPF). In this method, expressions for the impedance of a DGS slot are derived from self-reaction of the angular spectrum of plane waves and the discontinuity in the modal voltage. The numerical results are compared with those of the rigorous full-wave method and are shown to produce reasonably accurate data. And the stepped impedance microstrip low pass filter is designed and fabricated with the uniform and nonuniform DGS slots for improving the frequency responses. The experiments show that the proposed filter with slots in the ground plane has a wider stopband and sharper cutoff response.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.315-318
• /
• 1999

The purpose of this study is to establish the design theory of a DR ceramic bandpass filter used for WLL basestations and to research on the design theory of bandpass filter. The design procedure is circuit parameters and structural parameters will be derived. It was observed that the filter characteristics at the simulations

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.7 s.110
• /
• pp.673-683
• /
• 2006

In this paper, we investgate variation of phase and magnitude characteristics which become different as the variables of DGS are changed and propose the new method to easily decide the best optimum DGS pattern taking advantage of this trend. Generalized Chebyshev(GC) low pass filter(LPF) is designed by using DGS obtained from this method GC DGS LPF is more available for filter application than Chevyshev DGS LPF because GC LPF have parallel resonators as series circuits, therefore unlikely Chebyshev LPF, transform step of the series elements can be omitted. By using the proposed method, GC DGS LPF(N=5) and as a subject of comparison, conventional Chbyshev LPF(N=7) are designed and implementation. From the comparison of the measured data, we confirmed that the implemented GC DGS 5th order LPF have much better cutoff characteristics and reduce by 0.58 times size, on the other hand the stop bandwidth become widen about 1.57 times or more in comparison with the conventional Chevyshev 7th order LPF.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1734-1739
• /
• 2014

In this paper, microstrip low pass filter using transmission line with the modified DCRLH structure is designed and fabricated to be removed a spurious resonant mode, and a deep attenuation in stop band. The low pass filter is composed of shunt open-stub to get a deep attenuation and series short-stub to eliminate the spurious harmonics in stop band. In this way, the spurious harmonics occurring on the higher order frequency are suppressed and the filter performance is improved. Insertion loss and VSWR of the fabricated microstrip low pass filter in the passband from DC to 1.5 GHz is 1.26 dB and 1.65, and attenuation on the stopband from 1.84 GHz to 2.18 GHz is less than -100 dB. And also this filter has a good performance for 20 watt power test.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.3
• /
• pp.43-49
• /
• 2014

This paper presents a theoretical study of transmission performance for an optical duobinary transmitter employed a Mach-Zehnder modulator and a electrical low pass filter at 40Gbps optical communication links. It depends on the bandwidth of the low pass filter in the transmitter, the optical filter and the filter in the receiver. Also, each filter affected to the various parts of the optical power spectrum. By optimizing the bandwidth of each filter, we could control the side robes and the ripples and improve the dispersion tolerance of the transmission system.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.104-115
• /
• 2004

In this study, contains Design and Simulation data for Tone filter applied to the KSLV-1 FTS Receiver. Received Signal contains unwanted Noise and Jitter which should be eliminated by any kind of filters. In the design of KSLV-1 FTS Receiver, two different type of filters are used. One is Low-Pass Filter for rejecting high order harmonics and another is Tone Filter for sorting pure original signal in the mixed demodulate Signals. For the purpose of this development, various kinds of filter are studied and simulated for finding adequate type of filter.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.4
• /
• pp.257-262
• /
• 2015

In this paper, the split-ring DGS resonator is proposed and its equivalent circuit are analyzed to design the low pass filter. Compared with the conventional dumbell DGS cell, this structure has a flat fluctuation in low frequency range and a sharp slop at edge frequency. The out-band suppression of the SRR-DGS cell can be improved by placing the open stubs on the conductor line which operates as parallel capacitances. Making use of equivalent circuit analytical method, the characteristics of the improved SRR DGS cell are investigated and applied to design compact low pass filter, which has a low in-band loss, sharp slop and high suppression of more than 35dB within a wide out-band frequency range. The dependence of the transmission characteristic on the dimension of a split ring, such as side-length and split-gap, is analyzed in detail. In addition, an improved SRR DGS cell model with open stubs loaded on the conductor line is then presented to improve the out-band suppression. By using the equivalent-circuit analytical method, an S-band microstrip low-pass filter with perfect low-pass characteristic and high out-band suppression is designed and fabricated.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.1
• /
• pp.22-27
• /
• 2014

Blocking and ringing artifacts continue to be the most serious defects that occur in images and video streams compressed to low bit rates using block-based discrete cosine transform(DCT) compression standards. These artifacts contain the high frequency components near the block and the edge boundaries. Usually the lowpass filter can remove them. However, simple lowpass filter results into blur by removing important information such as edges at the same time. To overcome these problems, we propose a novel postfiltering algorithm that calculate the weight value based on the intensity similarity in the neighboring pixels and multiply this weight to the Gaussian lowpass filter coefficient. Experimental results show that the proposed technique provides satisfactory performance in both objective and subjective image quality.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.3C
• /
• pp.158-166
• /
• 2005

Even though post-processing methods based on projections onto convex sets (POCS) have shown good performance for blocking artifact reduction, it is infeasible to implement POCS for real-time practical applications. This paper proposes DCT domain post-processing method based on POCS. The proposed method shows very similar performance compared to the conventional POCS method, while it reduces tremendously the computational complexity. DCT domain POCS performs the lowpass filtering in the DCT domain, and it removes the inverse DCT and forward DCT modules. Through the investigation of lowpass filtering in the iterative POCS method, we define kth order lowpass filtering which is equivalent to the lowpass filtering in the kth iteration, and the corresponding kth order DCT domain POCS. Simulation results show that the kth order DCT domain POCS without iteration gives very similar performance compared to the conventional POCS with k iterations, while it requires much less computations. Hence the proposed DCT domain POCS method can be used efficiently in the practical post-processing applications with real-time constraints.