• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1854-1862
• /
• 2000

Input shaping method is to convolute input shaper, which is sequence of impulses, with reference input command not to excite the natural frequency of system. To reduce residual vibration for the ch ange of frequency, the number of impulses should be increased. Until now, amplitudes and time interval of those has been searched from the derivative of residual vibration. However, if time interval of impulses is fixed as the half of vibration period of system, input shaper H(z) in z-domain becomes (I-pz-1)n/K in which increasing n is the mean that robustness for change of parameter is improved. Also, design of many types of input shapers in z-domain is very easy because sensitivity curve is displayed with $\mid$H(z)zn$\mid$$\times$100. In the z-domain, EI(Extra-Insensitive) input shaper could be designed without solving nonlinear simultaneous equations as design in continuous time domain. In addition to, the design possibility of input shaper for a damped system was shown.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.542-549
• /
• 2012

This research is concerned with the derivation of equations of motion for a slewing beam and the application of input shaper to the bang-bang control to achieve vibration suppression. When a uniform beam with a tip mass rotates about the axis perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates. In this paper, we used the input shaper for the maneuvering control to suppress vibrations. The maneuvering control which can achieve a minimum-time control is a bang-bang control. The input-shaped bang-bang maneuvering is used to suppress vibrations both theoretically and experimentally. The slewing beam experiment is not an easy subject because of the inherent damping existing inside the rotor. We propose the use of a negative damping to eliminate the rotor damping. Numerical and experimental results show that the input-shaper can be effectively used for the vibration suppression of a slewing beam.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.707-714
• /
• 2012

After a single-stage, second-order, multiple-feedback ${\Delta}-{\Sigma}$ modulator and a two-stage, second-order MASH ${\Delta}-{\Sigma}$ modulator were analyzed and simulated using Simulink and Matlab and their characteristics were compared, the following result was obtained: 1) The two ${\Delta}-{\Sigma}$ modulators do not have group delay distortion. 2) The characteristics of the noise shaping are nearly identical. As a result of the noise shaping, the power spectral densities have slope of 40 dB/dec. 3) There was no spurious tone. 4) The input range of the two modulators is from -1 to +1 in common. 5) Because the output of the two-stage MASH modulator is 2-bits (4-levels), design of frequency dividers and charge pumps of PLL are more demanding.

• Journal of Drive and Control
• /
• v.17 no.2
• /
• pp.1-8
• /
• 2020

Recently, industrial systems are becoming quicker and lighter to enable the reduction of energy consumption and increase productivity. So the latest systems are more flexible and rapid than the previous systems. But, with this improvement, another problem has emerged, such as the increase in residual vibration when a system is started or stopped. The input shaper is a command generation method that can remove residual vibration. It can provide a solution to the problem of residual vibration in industrial systems. However, it is difficult to generate the input shaper in high order systems, such as a typical industrial system because the input shaper is induced from the system's vibration characteristics. This study focused on the extra insensitivity shaper that can compensate for the system's modeling error such as input dynamics, and the high order's system affection. A genetic algorithm was deployed to adjust a vibration limitation for the extra insensitivity of the input shaper. A plant is a low damping system that includes one zero and a pole. The fitness functions are an error signal of the system's response with normalized frequency variations. Verification of the suggested system is satisfied by comparison between the zero vibration derivative input shaper's response and the suggested one.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.1
• /
• pp.40-45
• /
• 2004

This paper presents the parallel distributed control scheme for shaping of the bent glass. The designed system consists of a PC, a main controller and 11 servo-controllers, the precision motion controllers. Each elements are connected by using RS-232C and 8-bit data bus. In order to guarantee the stability and the control performance, we use a precision PID motion controller and a H-bridge on the servo-drivers. PC calculates position values of 11 DC motors by using the pre-determined curvature value and offers the user interface environment operator. The main controller provides the control instructions and parameter values to 11 servo-controllers by chip enable signal, simultaneously. Using the received commands and parameter values, the servo-controllers control the positions of the DC motors based on PID control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1269-1272
• /
• 1996

Several input shaping techniques are suggested to reduce the vibration of a flexible manipulator. The theories of typical 4 methods(Singer, Tuttle, Feddema, Zuo) are explained and are tested by the experiment of one link flexible manipulator. Zuo's method is the best of all with respect to its robustness.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2000.11a
• /
• pp.67-72
• /
• 2000

PET는 합성섬유, 필름, 음료수병, 성형 플라스틱 등의 다양한 용도를 가지고 있으며 특히 섬유 원료부분에서는 전세계의 약 40%이상을 차지하고 있는 상업적 입장에서 아주 중요한 소재이다.［1］그러나, PET 제조공정은 긴 반응시간과 높은 반응온도, 대용량의 다단계 공정시설을 필요로 하는 대표적인 에너지 다소비 공정으로서 현대의 치열한 고분자 제품의 시장경쟁 상황에서 에너지 투입량 감축을 위한 공정의 해석 및 개발과 그로 인한 생산원가의 절감이 필수적이다. 본 연구에서는 실제 공장에서 사용되는 단일 연속식 직접 에스테르화 반응기(CSTR Direct Esterification Reactor)를 모델링하고 Van Krevelen［2］의 Group contribution method로 계산된 올리고머의 열용량값을 이용하여 에너지 소모량을 계산하였다. 모델링 결과는 모두 실제 공장의 자료와 비교되었으며 가장 제어하기 쉬운 변수에 따른 반응물의 물성과 에너지 소모량을 분석하였다. 또한 압력이 일정한 조건 하에서 입력변화에 따른 반응기의 동적 모델링을 동시에 수행하였으며 투입에너지량과 반응기의 운전지표와의 관계를 분석하였다. 이러한 연구는 실제 공정분석과 최적화에 있어서 소모 에너지량을 고려한 보다 정확한 지표를 제시하고 에너지 사용의 효율성을 높이는 데 기여할 수 있다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.361-367
• /
• 2010

The barrel cam, which is a type of cylindrical cam, has been widely used as a part of index drive units for automatic manufacturing machines. The axis of rotation of the barrel cam is orthogonal to the axis of rotation of the follower. The index drive rotates or dwells depending on the cam profile, while the cam rotates with a constant velocity. Continuous sliding contact between the barrel cam and the follower surfaces causes wearing of the adhesive between them. This study shows that the contact force between two sliding bodies is responsible for the wear of the barrel cam in the paper-cup-forming machine. This contact force is calculated by using the multibody dynamics model of the paper-cup-forming machine. The analytical result is validated by comparing it to the actual wear spots on the real product.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.537-540
• /
• 1987

항공기가 평형상태로 비행하는 도중 돌풍과 같은 외부교란을 만난 교란상태운동은 선형화된 미분방정식으로 표현되며 비교적 짧은 비행시간동안의 비행은 선형시 불변계가 된다. 돌풍은 Gauss-Markov확률과정으로 모델링 되며, 항공기가 돌풍을 만난 교란상태운동은 시스템론적으로 보면 백색잡음이 성형필터를 거쳐 계에 입력되는 것과 같다. 초기의 설계방법은 고전적인 주파수영역에서의 해석방법을 사용하였으나 1960년대에 최적제어이론이 도입되면서 평가함수를 사용하여 원하는 비행특성을 얻는 방법을 사용하게 되었다. 그 후 계에 입력되는 외란과 측정시의 잡음으로 인한 불확실한 측정량으로부터 최적상태변수의 추정을 위해 필터링이론을 도입한 확률제어이론을 적용하여 자동조종장치를 설계하게 되었다. 이때까지는 연속제어계로 설계되었으며 그 후 측정신호를 샘플링하여 연속제어계와 등가의 이산제어계를 사용한 자동조종장치가 등장하였으며 이 경우 설계기법으로는 연속제어계를 사용하고 실현시킬 때는 디지털컴퓨터를 사용하였다. 이는 제어하는 동안 계의 계수와 제어법칙을 바꾸어 줄 수 있는 이산제어계의 장점을 이용하지 못하므로 처음부터 계를 등가의 이산계로 보고 제어계를 설계하는 방법이 도입되었다. 이 때 샘플링간격의 결정과 Quantization 영향이 설계시 고려되어야 한다.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.10
• /
• pp.67-76
• /
• 2008

In this research, a simple technique for designing PID controller, which guarantees robust stability for two-mass systems with parameter uncertainties as well as rigid-body behavior and zero steady-state error,is described. As well, such a PID controller is designed to mate two important frequencies, at which the given system is excited, very close so that an appropriate reference profile generated by using command shaping techniques can cover those two frequencies. Root-locus analysis. which shows traces of closed-loop poles for the given system, is used to design this PID controller. Finally, feedforward controller is added to improve tracking performance of the closed-loop system. Simulation for a system with a flexible mode and parameter uncertainties is executed to prove the feasibility of this technique.