• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.3
• /
• pp.221-228
• /
• 2011

The large-area crystallization of amorphous silicon thin films on glass backplanes is one of the key technologies in the manufacture of flat-panel displays. Joule-heating induced crystallization (JIC) is a recently introduced crystallization technology. It is considered a highly promising technique for fabricating OLEDs, because the film of amorphous silicon on glass can be crystallized in tens of microseconds, minimizing thermal and structural damage to the glass. In this study, we theoretically and experimentally investigated the temperature variation during the phase transformation. The critical temperatures for crystallization were determined for both solid-solid and solid-liquidsolid transitions, by carrying out in-situ temperature measurements and numerical analysis of the JIC.

• Journal of Energy Engineering
• /
• v.7 no.2
• /
• pp.209-215
• /
• 1998

This paper investigated the vertical throughflow effects on natural convection due to heating from below in horizontal porous layer. The motion of the fluid in the porous layer is governed by Brinkman-Darcy equation. And compared Critical Rayleigh number in case of throughflow with no throughflow. Investigated Nusslet number, isothermalline and flow with the variation of the strength of throughflow in a constant Rayleigh number. In the numerical analysis, flow is assumed to be two-dimensional and unsteady. The numerical scheme used is a finite-difference method. In the experimental study, Temperature distribution was measured by use of Liquid Crystal film. As a results, indicated that throughflow influences largely on the temperature field and as the strength of throughflow increased, unstability of natural convection decreased. Also it could predict the strength of natural convection with the measured Nusselt number.

• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.28-33
• /
• 2005

A resource recovery technique using sub- and supercritical water hydrolysis was applied to recover amino aicds from waste fish entrails. The effect of reaction parameters such as temperature and time necessary for the control of reaction towards optimum yield of amino acids was investigated using semi-batch and batch reactors. Results showed a maximum yield of total amino acids (137 mg/g-dry entrails) from waste fish entrails at T=$250^{\circ}C$ (P=4 MPa) and reaction time of 60 min in a batch reactor. Under supercritical conditions (e.g., T=$400^{\circ}C$, P=45 MPa), the yield decreased due to rapid decomposition compared to production rate of amino acids. As a result, the low temperature and the short reaction time were needed to produce a maximum yield of amino acids.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.524-527
• /
• 2007

[ $Bi_2Sr_2Ca_{n-1}Cu_nO_x$ ](n=0, 1, 2) thin films have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about % K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $ CaCuO_2$ was observed in all of the obtained films.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.2
• /
• pp.83-87
• /
• 2003

$(Nd/Y)_{1.8}Ba_{}2.4Cu_{3.4}O_{7-x}$high $T_c$ superconductor was directionally grown by floating Bone melt growth process with a large temperature gradient in air. Cylindrical green rods of (Nd/Y)1.8 oxides were fabricated by cold isostatic pressing (CIP) method using rubber mold. Microstructures were observed by SEM and TEM and superconducting properties were measured by a SQUID magnetometer. Nonsuperconducting $(Nd/Y)_2BaCuO_5$ inclusions were uniformly distributed within the superconducting $(Nd/Y)Ba_2Cu_3O_x$ matrix. The directionally melt-textured (Nd/Y) 1.8 superconductor showed an onset Tc $\geq$ 90 K and a sharp superconducting transition.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.281-286
• /
• 2009

Bitumen extraction and sulfur removal from Athabasca oil sand were conducted using water in sub- and supercritical condition. Bitumen yield in micro reactor was investigated in the pressure range of 15~30 MPa, the temperature of 360 and $380^{\circ}C$ and water density $0.074{\sim}0.61g/cm^3$ for 0~120 min. Bitumen yield increased with reaction pressure irrespective of temperature and dramatically increased in especially supercritical region due to hydrogen formed from water gas shift reaction. Total amount of gas product decreased with reaction pressure but the portion of sulfur and hydrogen increased a little with increasing pressure to 25 and 30 MPa. It is seen that supercritical condition was favourable to the hydrogen formation and sulfur removal. Bitumen yield and sulfur removal from original oil sand reached a maximum 22% and 40% respectively in supercritical condition(the reaction time of 60 min at $380^{\circ}C$ and 25 or 30 MPa).

• Journal of Korea Water Resources Association
• /
• v.39 no.10 s.171
• /
• pp.833-844
• /
• 2006

The objective of this study is to evaluate the snowmelt effects on the hydrological components, especially on the runoff, by using the soil water assessment tool(SWAT) which is a continuous semi-distributed long term rainfall-runoff model. The model was applied to the basin located in the upstream of the Chungju Dam. Some parameters in the snowmelt algorithm were estimated for the Chungju basin in order to reflect the snowmelt effects. The snowmelt effects were assessed by comparing the simulated runoff with the observed runoff data at the outlet of the basin. It was found out that the simulated runoff with considering the snowmelt component matches more satisfactorily to the observed one than without considering snowmelt effect. The simulation results revealed that the snowmelt effects were noticeable on March and April. Similar results were obtained at other two upstream gauging points. The effect of the elevation bands which distribute temperature and precipitation with elevation was analyzed. This study also showed that the snowmelt effect significantly affects the temporal distribution as well as quantity of the hydrological components. The simulated runoff was very sensitive to the change of temperature near the threshold temperature which the snowmelt can occur. However, the reason was not accounted for this paper, Therefore, further analyses related to this feature are needed.

• Fire Science and Engineering
• /
• v.20 no.2 s.62
• /
• pp.80-86
• /
• 2006

This study focuses on spalling phenomenon which is the one of the main issues of high strength concrete. The definition, classification and characterization, causes and the reaction mechanism of the spalling were investigated on the basis of previous literatures. The spalling phenomenon occurs when several factors such as sharp temperature increase, high water content, low water/cement ratio and local stress concentration in material combine in the concrete material. On the basis o f the factors, the preventing methods from the spalling are known as decrease of temperature increase, preventing of concrete fragmentation and fast drying of internal moisture. In this study, the controlling method of water content below some critical value was proposed as the most effective spalling-preventing method among the spalling-preventing methods. The spalling phenomenon can be prevented by adjusting the water content in the high strength concrete. Therefore, an enforced drying method is needed to decrease the water content below a critical value. Additional experimental data should be generated to determine the critical value of water content for preventing the spalling.

• Nuclear Engineering and Technology
• /
• v.14 no.4
• /
• pp.196-203
• /
• 1982

To transport the spent fuel assemblies of Korea Nuclear Unit 1, which is a Westinghouse type two loop pressurized water reactor, it has been found that steel is the most appropriate material for the design of a shipping cask in comparison with lead and depleted uranium. The proposed shipping cask will transport nine fuel assemblies at the same time and is well within the weight limit of transportation by unrestricted rail car. The cask requires 33cm thick steel shield and 27cm thick water region to satisfy the 3 feet apart dose rate limit set forth in 10 CFR 71, and 1.27cm thick steel boron fuel basket to hold the fuel elements inside the cask and control the effective multiplication factor. As a safety analysis, the fuel cladding and centerline temperatures were calculated under the accident condition of complete loss of water coolant, and it was found that the temperature was much lower than the limit of the melting point. k$_{eff}$ was calculated with fresh fuel assemblies, which was found to be well lower than 0.95. For shielding computation, the multipurpose Monte Carlo code MORSE-CG and one dimensional discrete ordinates transport code ANISN were used, and the Monte Carlo codes KENO and MORSE-CG were used for criticality calculation. The radiation source terms were calculated using ORIGEN-79.9.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.6
• /
• pp.1115-1121
• /
• 2007

[ $Bi_2Sr_2Ca{_{n-1}}Cu_nO_x$ ](n=0,1,2) thin fans have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in all of the obtained films.