• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2615-2618
• /
• 2009

Double rectangular patch with 4-bridges is investigated for solution of IEEE 802.11b/g (2.4 GHz) and 802.11a (5.5 GHz). Rectangular patch for 5.5 GHz frequency band is printed on the PCB substrate and connected to another rectangular patch for 2.4 GHz frequency band with 4-bridges to obtain dual band operation in an antenna element. 4-bridges can modify the desired frequency band from its original frequency band by changing its width. Gain of 2.4 GHz patch is 5 dBi and 5.5 GHz patch is 3.7 dBi at ${\theta}=0^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.9-15
• /
• 2011

In this paper, we designed and fabricated a dual-band bandpass filter which can control upper and lower bandwidth using the transformed E-shaped dual-mode resonator. The filter is made the coupling between even-mode not to affect odd-mode resonant frequency by the transformed resonator to control upper bandwidth effectively. The cross coupling between input and output feed lines was employed to improve stopband characteristic. The bandpass filter has been designed to indicate the same bandwidth at center frequency 2 GHz and 3 GHz to show to control bandwidth.

• Journal of Advanced Navigation Technology
• /
• v.24 no.3
• /
• pp.232-237
• /
• 2020

In this paper, a compact microstrip-fed dual-band planar antenna for global positioning system (GPS) and mobile handset applications is presented. Dual operating frequency bands are achieved by an open end L-shaped slot and a bent rectangular slot. The proposed antenna is designed and fabricated on the FR4 substrate with dielectric constant of 4.3, thickness of 1.6 mm and size of 57 × 57 ㎟. The measured impedance bandwidth (|S₁₁|≤ -10dB) of the fabricated antenna is 60 MHz(1550 ~ 1610 MHz) in the GPS band and 670 MHz (1690 ~ 2360 MHz) in the DCS / IMT-2000 band, covering the required bandwidths for GPS(1570 ~ 1580 MHz) and DCS / IMT-2000 (1710 ~ 2200 MHz) bands. In particular, it has been observed that antenna has a good omnidirectional radiation patterns as well as high gain of 2.36 dBi and its efficiency is more than 90 % over the entire frequency band of interest.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1423-1431
• /
• 2010

In this paper, the dual-band compact broad bandpass filter using parallel coupled line is proposed. The proposed filter has reduced size and can be controlled bandwidth. And it is also possible to operate in the dual-band purpose. Futhermore, the inserted bandstop fiilter with T-type configuration is also possible to operate in the same purpose. The dual-band bandpass filter has the first operating frequencies and its bandwidth which are 5.8 GHz and 60 % respectively and the second operating frequency and the bandwidth are 16.2 GHz and 60 % respectively. The insertion loss and the return loss of the first frequency has 0.4 dB and 17.4 dB and the insertion loss and the return loss of the second frequency has 0.62 dB and 19.8 dB, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.517-521
• /
• 2018

In this paper, we designed a microstrip antenna for LTE / WLAN for wireless mobile communication high - speed communication network. The substrate of the proposed antenna is FR-4 (er = 4.3), the size is $20[mm]{\times}40[mm]$ and can be used in the frequency band of 2.77 [GHz] and 5 [GHz] Respectively. The simulation was performed using CST Microwave Studio 2014. The simulation result shows that the gain is 2.034 [dBi] at 2.77 [GHz] and 4.95 [dBi] at 5 [GHz]. The S-parameter was also found to be less than -10 [dB] (WSWR 2: 1) in the desired frequency band. The frequency bands of LTE and WLAN are widely used around the world, and the usage of the frequency is also increasing. For this reason, the dual-band antenna of LTE / WLAN is designed to help many users in a good way to use both technologies.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.116-126
• /
• 2008

This paper describes the Dual-band WLAN transmitter with 2.4[GHz], 5[GHz]. Dual-band WLAN transmitter was designed at 2.4[GHz] and 5[GHz]. The Dual-band WLAN transmitter has a amplifier which operate at 2.4[GHz] and 5[GHz] frequency and two VCO(Voltage Controlled Oscillator) or VCO has a wide scope of frequency. these problem cause a size and a power consumption, The Dual-band WLAN transmitter module was proposed to solve these. the transmitter was designed to get output signals of IEEE 802.11a's 5.8[GHz] band signal using frequency multiplication way or to act a amplifier about the 2.4[GHz] band signal of IEEE 802.11b/g, according to inputed frequency and bias voltage that a eve using single transmission block. The output spectrum get the improved specification of ACPR of 4[dB], 6[dB], 16[dB] at +11[MHz], +20[MHz], +30[MHz] offset of center frequency compared to no linearization, was satisfied to transmit spectrum mask of IEEE 802.11a wireless Lan.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.10 s.113
• /
• pp.993-999
• /
• 2006

This paper presents the design simulation, implementation, and measurement of a miniaturized DCS, PCS / Satellite DMB dual-band stacked chip antenna with double coupled line for mobile communication terminals. A stacked meander is realized by using a via hole with height of 0.8 mm and a diameter of 0.35 mm to connect upper- and lower-layer meander sections for a reduction of the dimensions of the antenna. In addition the stacked meander chip antenna is extended by a double coupled-line to achieve two different radiation modes. A ratio of the first frequency and second frequency vary with the geometrical parameter of coupled lines. The fabricated antenna used FR-4 substrate with relative permittivity of 4.2. And its dimensions are $15.2{\times}7{\times}0.8mm^3$. The measured impedance bandwidth(VSRW<2) are 244 and 120 MHz at the operating frequency, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.1-5
• /
• 2017

In this paper, we propose a wideband band-stop filter (BSF) in order to extend the stopband of the band-stop filter using a symmetric dual spurline and the coupled open stub. First, we know that the symmetric dual spurline structure is advantageous in widening the stopband, as compared to the asymmetric dual spurline structure. So we designed a band-stop filter that combines the electrically coupled open stub (ECOS) band-stop filter with a symmetric dual spurline. We can greatly extend the stopband, when it is combined with the dual spurline and electrically coupled open stub on a microstrip transmission line, without any size increment. The stopband of the proposed band-stop filter is extended by approximately 244% (rejection depth: -20 dB) compared with a band-stop filter without a dual spurline.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.140-141
• /
• 2003

광섬유 통신에서 넓은 대역폭 증폭을 이루기 위하여 광대역 증폭기가 필요하다. 증폭기의 대역폭을 넓히기 위해 C-대역과 L-대역 EDFA를 결합하여 사용하는 등의 여러 가지 방법이 제안되고 있다. 그 중 L-대역을 결합하는 방법이 실제 시스템 적용에서 가장 즉시 이용가능한 방법이라 할 수 있다. L-대역 EDFA의 경우 상대적으로 이득이 낮으며 효율이 떨어진다. 이득이나 효율을 높이기 위해서 FBG, 양방향 펌핑(bidirectional pump), 그리고 이중경로(double-pass) 구조를 이용하는 방법이 제안되었다. (중략)

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2023

This paper presents a novel method of implementing a dual-band antenna using a square patch with an inset feed structure. The proposed method is to simply design a dual-band antenna using an asymmetric inset structure with different lengths of slots dug into the patch for inset feeding. To verify the proposed method, a dual-band inset patch antenna supporting 1.57 GHz GPS and 2.4 GHz WiFi bands was designed and manufactured on a 1 mm thick FR4 substrate. From measurement, it was confirmed that the frequency bands of the antenna that satisfy a return loss of -10dB or less are 1.55~1.57GHz and 2.41~2.45GHz, which has dual-band characteristics. Using the proposed method, it is possible to simply implement a dual-band antenna using inset feeding, and it is expected to be utilized in a variety of application fields.