• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.5
• /
• pp.499-506
• /
• 2019

This paper is concerned with the operating stability of 7kW inverter using SIC hybrid module and verifies the validity of the simulation results by comparing the result of the loss equation and the simulation result, Simulation results using Si module and SiC hybrid module are compared to compare switch loss and diode loss. Through the loss equation calculation, the conduction loss of SiC Hybrid module is 168W, switching loss is 9.3W, diode loss is 10.5nW, When compared with the simulation results, similar values were shown. As a result of comparing the simulation results of the Si module and the SiC Hybrid module, The total device loss of the Si module was 246.2W, and the total device loss of the SiC Hybrid module was 189.9W. The loss difference was 56.3W, which was about 0.8W. thereby verifying the reverse recovery characteristics of the SiC SBD. In addition, temperature saturation test was conducted to confirm the stability of SiC Hybrid module and Si module under high temperature saturation, In the case of the Si module, the output power was stopped at 4kW, and the SiC Hybrid module was confirmed to operate at 7kW. Based on this, an efficiency graph and a temperature graph are presented, and the Si module is graphed up to 4kW and the SiC Hybrid module is graphed up to 7kW.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.121-127
• /
• 2016

We propose a algorithm to calculate power factor of fundamental waveform in an environment where the voltage and current have been distorted by harmonics. In the proposed power factor computation algorithm, voltage and current are converted to rotating DQ reference frame, and power factor is calculated from active power and reactive power. We compare the proposed method with the conventional power factor measurement method as mathematically. In a condition that voltage and current are distorted by harmonics, the proposed method accurately measure the power factor of fundamental wave, and it is confirmed by simulation using MATLAB. If the proposed power factor measurement method is applied to an automatic power factor control system, a power factor compensation performance can be maximized in harmonic distortion environment. As a result, it is possible to reduce electricity prices, reduce line loss, increase load capacity, ensure the transmission margin capacity, and reduce the amount of power generation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.228-228
• /
• 2007

전력선 통신용 비접촉식 커플러는 고속형(2~30 MHz)과 저속형(100~450KHz)으로 나누어 볼 수 있는데, 고속형은 현재 국내에서 독자적으로 개발되어 다양한 모델이 적용되고 있는 상황이지만, 저속형은 시작품수준으로 제조되어 있으나 신호전송 특성의 향상절구가 필요한 상황이다. 전력선 통신용 커플러는 전력선 또는 모뎀으로 통신신호를 전달하는 기능을 하는 것으로서, 전력선 통신을 위한 핵심부품이다. 따라서 본 연구에서는 100~450 KHz 대역에서 사용 가능한 저속형 비접촉식 커플러를 제조하기 위해, 권선조건, 대전류형 자심재료의 모의 해석, 노이즈 필터조건, 임피던스 매칭, 하우징방법 등의 각 공정 변수를 확립하고자 하였다. 자심재료의 모의해석에서 자심재료의 높이와 전력선 도체 단면적 변화는 자심재료의 전류포화특성에 영향을 미치지 않으며, 유효길이와 에어-갭 크기가 증가할수록 전류포화특성은 향상되는데, 자심재료의 내경이 64 mm일 때 자심재료의 폭((외경-내경)/2)은 15 mm 이상이어야 하고, 에어-갭은 약 $600\;{\mu}m$ 정도의 에어-갭을 형성시켜야함을 확인할 수 있었다. 또한 저속용 비접촉식 커플러 제조조건 실험에서 내경${\times}$외경${\times}$높이가 $64{\times}94{\times}140mm$인 자심재료를 이용하여 권선 수와 에어-갭을 각각 3회, $400{\sim}600\;{\mu}m$ 삽입했을 때, 가장 우수한 특성을 나타내었다. 그리고 저역 통과 필터를 출력부에 내장하여 통신신호 이외의 노이즈를 제거할 수 있었다. 본 연구에서 제조된 300 A급 지중선용 저속형 비접촉식 커플러는 내경${\times}$외경${\times}$높이가 $58{\times}1144{\times}158mm$이고, 100~450 KHz 통신대역에서 약$7{\pm}2dB$의 삽입손실을 나타내었다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.1
• /
• pp.146-153
• /
• 2004

This paper presents the method for the placement and operation of dispersed generator systems(DGs) using fuzzy goal programming in distribution systems. For the placement and operation of DGs the problem is formulated with reduction of search spaces and flexibility of system situations. Especially, the original objective function and constraints are transformed by fuzzy goal programming to evaluate their imprecise nature for the criterion of power loss minimization, the number or total capacity of DGs and the bus voltage deviation, and then solve the problem using genetic algorithm.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.342-346
• /
• 2006

A polymeric ring resonator with electrically variable extinction ratio at resonant wavelengths has been proposed and demonstrated. It consists of a ring waveguide coupled to a straight bus waveguide and a modulating electrode, which is formed in the outer cladding region outside of the ring. When electrical power is applied to the electrode, the refractive index of the polymers underneath the electrode is lowered to strengthen the confinement of the guided mode of the ring and thus the equivalent effective refractive index felt by the mode is decreased. Therefore, the propagation loss of the guided mode is reduced with the applied electrical power Consequently the extinction ratio at resonant wavelengths is varied by the electrical power. For the achieved results, the extinction ratio was changed by about 9 dB for the electrical power of 12 mW, when the propagation loss of the ring was reduced by 80 dB/cm.

• The KIPS Transactions:PartC
• /
• v.13C no.6 s.109
• /
• pp.677-684
• /
• 2006

This paper investigates the link margin of MB-OFDM UWB system quantitatively. Various simulations are performed considering the implementation loss by imperfect synchronization unit and the effect of multi-path fading channels. MB-OFDM UWB system uses ZP(Zero Padding) instead of CP(Cyclic Prefix) and supports two transmission modes; one is TFI(Time Frequency Interleaving) mode that transmits OFDM symbols using different carrier frequency from symbol to symbol according to Time Frequency(TF) codes, the other is FFI(Fixed Frequency Interleaving) mode that transmits OFDM symbols using a specific carrier frequency. The advantage of if and TFI is to be able to increase the transmitting power effectively compared to the existed OFDM systems that transmit the signal continuously at the same average transmitting power. From the analysis results of Ink margin, to guarantee the service range of 4m in 200Mbps mode, TFI mode must necessarily be implemented and the service range of 480Mbps mode is estimated about 1-2m in the line-of-sight multi-path channel (CMI).

• Journal of KIISE:Information Networking
• /
• v.33 no.4
• /
• pp.299-309
• /
• 2006

In Mobile ad hoc networks, AODV is one of the famous on-demand routing protocol, which use the routing tables in the nodes if possible, or Route Discovery Process (RDP) is triggered to find a new route. However increasing the traffic of RDP causes dropping of the network performance in the large size of ad hoc networks. In this paper, we propose a novel routing protocol, named as AOZDV (Ad hoc On-demand Zone and Distance-Vector Routing), which enhances the AODV protocol with zone routing. AOZDV creates a Zone with neighbor nodes of the source/destination using traffic and power information, and utilizes Destination-Vector Table for internal routing in the Zone. We show by simulations that AOZDV can reduce the occurrence rate of route fail and RDP caused by route fail compared to existing routing protocols such as DSR and AODV.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.111-113
• /
• 2009

침몰한 잠수함 승조원의 구조용으로 사용되는 구난잠수정은 주 전원과 보조전원으로 축전지가 필수적으로 사용된다. 그러나 사용 중인 축전지 모듈이나 뱅크의 일부 셀(Cell)에 불량이 발생하면 전체 축전지 뱅크의 기능이 저하되어 구난정 시스템을 적절히 운영하지 못하여 제대로 임무를 수행하지 못하거나 커다란 손실을 가져온다. 그리고 축전지에 과 충전이나 과 방전이 발생하면 축전지가 폭발하여 화재가 발생하거나 축전지 내부 구조의 파괴로 더 이상 사용 못하는 경우가 발생한다. 따라서 이와 같이 축전지에 손상을 줄 수 있는 상황을 미연에 방지하여 축전지가 최적의 동작 상태를 유지할 수 있도록 해주고 전체 시스템의 신뢰성을 향상시키기 위하여 본 논문에서는 구조잠수정용 리튬폴리머 (Lithium Polymer) 축전지 관리장치의 개발을 수행하였다. 본 논문을 통해 축전지 관리 장치(BMS : Battery Management System)의 핵심기술인 H/W 및 S/W 설계기술, 각 Cell의 전압 제어기술, SOC(State of Charge) 제어 알고리즘 도출 및 시스템 운영 기술을 구현하였으며 개발된 알고리즘과 기능은 충 방전 부하시험과 한국 선급인증시험을 통해 유효한 방식임을 확인하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.3
• /
• pp.221-228
• /
• 2008

In the 2-phase excited BLDC motor drives using a unipolar PWM scheme, there exists, in some cases, a unwanted leakage current which flows through the anti -parallel diode in the non-excited phase leg of the inverter. In this paper the cases in which the leakage current exists and the influence of the leakage current are analyzed, and a novel unipolar PWM scheme which can eliminate the leakage current is proposed. The leakage current increases as the motor speed is increased or PWM duty is decreased, and as a result the output power of the motor is reduced considerably. The effectiveness of the proposed unipolar PWM scheme isverified through the comparative simulations and experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.65-72
• /
• 2004

This paper proposes the novel boost input type resonant AC/DC converter. Since the proposed converter is single stage topology, it controls both of the input power factor and the output voltage at the same time, and resultingly obtains the high power factor of 99% with average current mode pulse width modulation. Especially, to accomplish the zero voltage switching, the resonance between the leakage inductance and external capacitor is used. For the theoretical consideration of the proposed converter, the six operation modes divided by means of current path are discussed, and the resonance characteristics in steady state are analyzed. To verify the validity of the proposed converter, a 200[W]($120[V_AC],\; 출력\; 48[V_DC],\; 4[A]$prototype converter was built and its experimental results were presented in this paper.