• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.675-677
• /
• 2009

통신기기에서 중요한 기술 중 하나인 PLL(Phase Locked Loop) 회로는 주기적인 신호를 원하는 대로, 정확한 고정점으로 잡아주는데 그 목적을 둔다. 일반적인 구조로 위상주파수검출기(Phase Frequency detector), 루프필터(Loop filter), 전압제어발진기(Voltage Controlled Oscillator), 디바이더(Divider)로 구성되어진다. 그러나 일반적인 PLL 구조로는 지터(jitter)가 증가하고 트랙(tracking) 속도가 느리다는 단점이 있다. 이를 보완하기 위해 루프필터 전단에 차지펌프(Charge pump) 회로를 추가하여 사용하고 있다. 본 논문에서는 CMOS를 이용한 PLL용 차지펌프를 설계하였다. 설계된 회로는 $0.18{\mu}m$ CMOS 공정 기술을 사용하여 CADENCE사의 Specter로 시뮬레이션 하였으며, Virtuso2로 레이아웃 하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.690-692
• /
• 2009

PLL은 위상주파수검출기(PFD), 차지펌프(Charge Pump), 루프필터(Loop Filter), 전압제어발진기(VCO), Divider로 구성하고 있는데 본 논문에서는 설계된 차지펌프 PLL을 시뮬레이션을 해보고 그 결과를 정리하고 레이아웃(layout)까지 하였다. 차지펌프 설계에 있어서 전류 부정합, 전하 공유, 전하주입, 누설 전류등을 고려할 필요가 있다. 설계된 차지펌프는 전류 부정합을 감소시키기 위해 전류뺄셈회로를 이용하여 전류 부정합을 감소시켰으며, spurs를 억제할 수 있도록 설계되였다. 설계된 회로는 $0.18{\mu}m$ CMOS 공정 기술을 사용하여 CADENCE사의 specter로 시뮬레이션 하였으며, virtuso2로 레이아웃 하였다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.271-275
• /
• 2014

A New Single Phase Active Power Filter Controller is proposed using Rotating Synchronous Frame d-q transformation. Instantaneous Active Power is calculated using d-q transformation. Average Value of Instantaneous Active Power is obtained using Low Pass Filter. Because power factor is corrected, source current is in phase with source voltage. Amplitude of source current is calculated using single phase power formula. Reference signal of compensated current of Active power filter is obtained from source current reference signal minus load current. Simulation is performed using hysteresis current controller in proposed new controller. Simulation result shows that because active power filter compensates load current, source current is in phase with source voltage and source current is sinusoidal. And Hilbert transformer is builded using all pass filter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.130-134
• /
• 2008

This paper presents a clock and data recovery(CDR) using a quarter-rate technique. The proposed CDR helps reduce the VCO frequency and is thus advantageous for high speed application. It can achieve a low jitter operation and extend the pull-in range without a reference clock. The CDR consists of a quarter-rate bang-bang type phase detector(PD) quarter-rate frequency detector(QRFD), two charge pumps circuits(CPs), low pass filter(LPF) and a ring voltage controlled oscillator(VCO). The Proposed CDR has been fabricated in a standard $0.18{\mu}m$ 1P6M CMOS technology. It occupies an active area $1{\times}1mm^2$ and consumes 98 mW from a single 1.8 V supply.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.173-179
• /
• 2001

This paper represents the control algorithm of the instantaneous voltage sag corrector for the power quality enhancement in distribution line. Especially, a novel detection technique of the symmetrical components is proposed for the analysis of the three-phase unbalanced and asymmetrical problems caused by the single line ground fault which is he most frequent event. This proposed method is based on the simple calculation and the control references of the symmetrical components for voltage compensation can be described as dc value without any other phase detection procedure. And also, for the generation of the reference voltages, the UF and MF defined by IEC is considered. Using this proposed control algorithm, the compensator has the fast dynamic characteristics and the THD of the compensated voltage waveform is very low. Finally, the validity of the proposed algorithm is proved by the PSCAD/EMTDC simulation and experimental results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.7
• /
• pp.545-551
• /
• 2013

Timing recovery loop composed of the Timing Error Detector(TED), loop filter and resampler is widely used for the timing synchronization in MQASK receivers. Since TED is sensitive to the delay between the symbol period of the signal and sampling period, the output is averaged out when the symbol rate and sampling rate are quite different the recovery loop cannot work at all. This paper presents a sampling frequency discriminator (SRD), which detects the frequency offset of the sampling clock to the symbol clock of the MQASK data transmitted. Employing the SRD, the closed loop timing recovery scheme performs the frequency-aided timing acquisition and achieve the synchronization at extremely high sampling frequency offset, which can be used in variable symbol rate MQASK receivers.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.975-981
• /
• 2020

A 10 GHz LC voltage-controlled oscillator (VCO), which controls an amplitude of output signal, is proposed to improve the phase noise. The proposed amplitude control circuit for the LC VCO consists of a peak detector, an amplifier, and a current source. The peak detector is performed detecting the lowest voltage of the output signal by using two diode-connected NMOSFET and a capacitor. The proposed 10 GHz LC VCO with an amplitude control circuit for output signal is designed using a 55 nm CMOS process with a supply voltage of 1.2 V. Its area is 0.0785 ㎟. The amplitude control circuit used in the proposed LC VCO reduces the amplitude variation 242 mV generated in the output signal of the conventional LC VCO to 47 mV. Furthermore, it improves the peak-to-peak time jitter from 8.71 ps to 931 fs.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1257-1264
• /
• 2019

A 3-GSymbol/s/lane transceiver, which supports the mobile industry processor interface (MIPI) C-physical layer (PHY) specification version 1.1, is proposed. It performs channel mismatch correction to improve the signal integrity that is deteriorated by using three-level signals over three channels. The proposed channel mismatch correction is performed by detecting channel mismatches in the receiver and adjusting the delay times of the transmission data in the transmitter according to the detection result. The channel mismatch detection in the receiver is performed by comparing the phases of the received signals with respect to the pre-determined data pattern transmitted from the transmitter. The proposed MIPI C-PHY receiver is designed using a 65 nm complementary metal-oxide-semiconductor (CMOS) process with 1.2 V supply voltage. The area and power consumption of each transceiver lane are 0.136 ㎟ and 17.4 mW/GSymbol/s, respectively. The proposed channel mismatch correction reduces the time jitter of 88.6 ps caused by the channel mismatch to 34.9 ps.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.359-369
• /
• 2020

In this paper, we proposed a charge pump (CP) circuit that has a wide operating range while reducing the current mismatch for the PLL that generates the main clock of the CMOS X-Ray detector. The operating range and current mismatch of the CP circuit are determined by the characteristics of the current source circuit for the CP circuit. The proposed CP circuit is implemented with a wide operating current mirror bias circuit to secure a wide operating range and a cascode structure with a large output resistance to reduce current mismatch. The proposed wide operating range cascode CP circuit was fabricated as a chip using a 350nm CMOS process, and current matching characteristics were measured using a source measurement unit. At this time, the power supply voltage was 3.3 V and the CP circuit current ICP = 100 ㎂. The operating range of the proposed CP circuit is △VO_Swing=2.7V, and the maximum current mismatch is 5.15 % and the maximum current deviation is 2.64 %. The proposed CP circuit has low current mismatch characteristics and can cope with a wide frequency range, so it can be applied to systems requiring various clock speed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.332-338
• /
• 2002

High current coil power supply for superconductivity coil of tokamak requires fast dynamics performance of di/dt and smooth change over of current direction. To meet the specification high performance DSP-based controller Is designed for 12-pulse thyristor dual converter with interphase transformer(IPT). Not only the total current of Y and $\Delta$ converter units but also the difference for those should be regulated fast and accurately. Proportional and integral controller is designed for current difference control and the controller output is compensated to $\Delta$ converter. The source voltage phase angle detection and gate pulse generation algorithm are implemented in software for higher reliability of current control. The current error Is reduced by selection of appropriate initial gating angle during the transient of change over of current direction between thyristor converters.