Journal of the Korean Crystal Growth and Crystal Technology
/
v.12
no.4
/
pp.210-214
/
2002
The crystallization behavior of amorphous silicon (a-Si) film was investigated by using Cu-field aided lateral crystallization (Cu-FALC) process below $450^{\circ}C$. The lateral crystallization was induced from the Cu deposited region outside of pattern toward the Cu-free region inside of the pattern by applying an electric field during heat treatment. As expected, the lateral crystallization toward Cu-free region proceeded from negative toward positive electrode side. The occurrence of Cu-FALC phenomenon was interpreted in terms of dominant diffusing species in the reaction between Cu and Si. Even at the annealing temperature of $350^{\circ}C$, the large dendrite-shaped branches were formed in the crystallized region and the polarity in the lateral crystallization was clearly observed. Consequently, we could successfully crystallize the a-Si at the temperature as low as $350^{\circ}C$ by an electric field of 30 V/cm with fast crystallization velocity of 12 $\mu$m/h.
Transactions of the Korean Society of Mechanical Engineers B
/
v.20
no.5
/
pp.1671-1678
/
1996
In external chemical vapor deposition processes including VAD and OVD the distribution of flame-synthesized silica particles is determined by heat and mass transfer limitations to particle formation. Combustion gas flow velocities are such that the particle diffusion time scale is longer than that of gas flow convection in the zone of particle formation. The consequence of these effects is that the particles formed tend to remain along straight smooth flow stream lines. Silica particles are formed due to oxidation and hydrolysis. In the hydrolysis, the particles are formed in diffuse bands and particle formation thus requires the diffusion of SiCl$\_$4/ toward CH$\_$4//O$\_$2/ combustion zone to react with H$\_$2/O diffusing away from these same zones on the torch face. The conversion kinetics of hydrolysis is fast compared to diffusion and the rate of conversion is thus diffusion-limited. In the language of combustion, the hydrolysis occurs as a Burke-Schumann process. In selected conditions, reaction zone shape and temperature distributions predicted by the Burke-Schumann analysis are introduced and compared with experimental data available. The calculated centerline temperatures inside the reaction zone agree well with the data, but the calculated values outside the reaction zone are a little higher than the data since the analysis does not consider diffusion in the axial direction and mixing of the combustion products with ambient air. The temperatures along the radial direction agree with the data near the centerline, but gradually diverge from the data as the distance is away from the centerline. This is caused by the convection in the radial direction, which is not considered in the analysis. Spatial distribution of silica particles are affected by convection and diffusion, resulting in a Gaussian form in the radial direction.
Proceedings of the Korean Vacuum Society Conference
/
2014.02a
/
pp.379.1-379.1
/
2014
그래핀은 뛰어난 기계적, 화학적, 광학적, 전기적 특성을 가지고 있는 2차원 물질로써, 화학기상증착법을 이용한 대면적 합성법과 전사 공정을 통해 다양한 기판에서 사용이 가능해지면서 차세대 전자소재로 활용하기 위한 활발한 연구가 이루어지고 있다. 상온 대기에서 간편하게 적용 가능한 고분자용액공정을 도입하여, 그래핀과 폴리에틸렌이민(polyethyleneimine)의 다양한 적층구조를 제작하였다. 폴리에틸렌이민의 높은 밀도의 극성 기능기와 그래핀의 가스배리어 특성을 이용한 상호 보완적인 구조를 형성하여 외부 환경에 장시간 안정적이고 효과적인 n형 도핑 효과를 유지하였다. 그래핀에 결함 형성없이 도핑 농도 조절이 가능하며, 그래핀 고유의 선형적인 상태밀도를 이용한 일함수 조절효과를 확인하였다. 그래핀 p-n 접합 소자를 제작을 통해 베젤라고 렌즈 효과, 반정수 양자 홀 효과를 이용한 기초 연구에 접근이 가능할 것으로 보이며, 응용 분야에서는 태양광전지, 유기 전자 소자 분야 등 그래핀을 이용한 전기적 접촉 개선에 활용될 수 있을 것으로 보인다.
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.183-183
/
2000
Aigrain에 의해 Helicon이라는 이름이 명명된 이후, helicon은 저온의 금속과 같은 높은 전도도(conductivity)를 갖는 매질이나 강한 자기장이 걸려있는 plasma를 전파해 나가는 저주파 전자기장을 지칭해왔다. 이온화된 개스에서 이러한 전자기장은 전자 공명 주파수(electron cyclotron frequency)와 이온 공명 주파수(ion cyclotron frequency) 사이의 주파수로 전파하며 전리층 (ionosphere)을 통과하며 발생하는 가청 주파수 영역대의 음조가 강하하는 현상에 의해 low-frequency whistler라고도 불린다. Helicon wave plasma는 Boswell에 의해 처음 발생된 후, 높은 이온화율(~100%)로 인해 많은 연구가 이루어져 왔다. 1985년에 Chen은 helicon plasma의 높은 이온화율을 설명하기 위해 Landaudamping을 제시하였다. 이러한 설명은 1997년에 Shamrai에 의해 TG mode가 도입되기 전까지 직접적인 실험결과 없이 helicon plasma 발생의 mechanism으로 받아들여졌다. shamrai의 이론에 의하면 정전기파(electrostatic wave)는 plasma의 표면(surface)에서 강하게 감쇄되어 energy를 전달하게 된다. Cho는 radial density 분포가 외각보다 중심이 높을 경우 TG wave의 power 전달이 중심에서 일어날 수 있음을 계산하였다. Helicon plasma의 특성은 높은 이온화율에 의한 높은 밀도($\geq$1012cm3), 1-2 kW의 rf power에서 상대적으로 낮은 전자 온도( 4eV), $\omega$ci $\omega$LH<$\omega$$\omega$ce $\omega$pe 영역대의 주파수, 자기장 50-1200 Gauss, 압력 1-10 mTorr로 특정지을 수 있다. 이러한 외부분수들의 조건에 k라 helicon plasma는 여러 종류의 mode로 존재한다. Degeling은 이러한 mode의 변화를 capacitive mode, inductive mode, 그리고 helicon mode(wave mode)의 세가지 부분으로 구분하였다. Helicon plasma가 갖는 높은 이온화율은 여러 가지 응용으로의 가능성을 가지고 있다. 그 예로 plasma processing, plasma wave에 의한 입자 가속, 그리고 가스 레이저 활성 매질 발생 등이 있다. 특히 plasma processing의 경우 helicon plasma는 높은 밀도, 비교적 낮은 자기장, remote operation 등이 가능하다는 점에서 현재 연구가 활발히 진행되고 있다. 상업용으로도 PMT와 Lucas Signatone Corp.에 서 helicon source가 제작되었다. 또한 높은 해리율을 이용하여 저유전 물질인 SiOF의 증착에서 적용되고 있다. 이 외에도 다수의 연구결과들이 발표되었다.
Proceedings of the Korean Vacuum Society Conference
/
2011.02a
/
pp.45-45
/
2011
알루미늄과 그 합금은 내부식성(corrosion resistance)이 좋고, 밀도가 낮아 높은 연료소비 효율을 필요로 하는 항공기와 자동차 같은 운송수단의 내-외장 소재로 사용되고 있다. 또한 알루미늄의 높은 내부식성을 이용하여 철강소재의 부식을 방지하는 보호막으로도 폭 넓게 사용된다. 물리기상증착(physical vapor deposition)으로 알루미늄을 코팅하면 박막 성장 초기단계에서 핵(nucleus)을 형성하고, 형성된 핵을 중심으로 주상 구조(columnar structure)로 박막이 성장하는 것이 일반적으로 알려진 방식이다. 주상 구조의 알루미늄 박막은 주상정과 주상정 사이에 필연적으로 공극(pore)이 존재하게 되어 부식을 일으키는 물질이 박막으로 침투하게 되고, 부식 물질과 모재가 반응하여 공식(pitting corrosion)이 발생한다. 본 연구에서는 스퍼터링(magnetron sputtering)을 이용하여 치밀한 조직을 갖는 알루미늄 박막을 코팅할 수 있는 공정을 개발하고, 치밀한 알루미늄 조직이 내부식성에 어떠한 영향을 미치는지 평가하였다. 기판은 냉연강판(cold rolled steel sheet)이 사용되었으며, 알루미늄 타겟의 순도는 99.999%, 크기는 직경 4"이었다. 냉연강판은 진공용기(vacuum chamber)에 장착하기 전에 계면활성제를 이용하여 표면에 존재하는 기름성분을 제거하였으며, 진공용기에 장착한 후에는 아르곤 가스를 이용하여 발생시킨 글로우 방전으로 표면에 존재하는 산화물을 제거하였다. 알루미늄 박막의 조직에 영향을 미치는 공정변수를 확인하기 위해서 스퍼터링 파워, 공정 온도, 공정 압력, 외부 자기장 세기 등의 공정 조건을 변화시켜 코팅을 실시하였다. 실험을 통해서 얻어진 최적 조건으로 알루미늄을 코팅할 경우, 알루미늄 bulk의 밀도와 비교하여 약 94.7%의 밀도를 갖는 알루미늄 박막을 코팅할 수 있었다. 알루미늄 박막이 약 3 ${\mu}$m의 두께로 코팅된 냉연강판의 내부식성 평가(salt spray test, 5% NaCl) 결과, 평가를 시작한 후 72시간 후에도 적청이 발생하지 않았다.
For hybrid water treatment of carbon fiber ultrafiltration and photocatalyst, we used the hybrid module that was composed of photocatalyst packing between tubular membrane outside and module inside. Photocatalyst was PP (polypropylene) bead coated with $TiO_2$ powder by CVD (chemical vapor deposition) process. Water back-flushing of 10 sec was performed per every period of 10 min to minimize membrane fouling for modified solution, which was prepared with humic acid and kaolin. Resistance of membrane fouling ($R_f$) decreased as humic acid concentration changed from 10 mg/L to 2 mg/L, and finally the highest total permeate volume ($V_T$) could be obtained at 2 mg/L, which was the same with the previous results. Then, treatment efficiencies of turbidity and humic acid were above 98.9% and 88.7%, respectively, those did not depend on the humic acid concentration. However, the treatment efficiency of humic acid increased a little as the humic acid concentration increased in the previous results.
Journal of the Microelectronics and Packaging Society
/
v.9
no.3
/
pp.37-41
/
2002
In this research, we investigate the properties of membrane and thin film sensor which is using magnetic resonance properties. we expect to $Si_xN_y$ and SiC materials as membrane materials, we measured thin film stress and properties to find the best membrane fabrication condition. Of the two membrane, $Si_xN_y$ thin film is the better than SiC thin film. because of an adequate tensile stress and lower thermal expansion coefficient as sensor structure layer. After performing deposition and patterning thin film sensor material on $Si_xN_y$, we analyzed the magnetic hysteresis and magnetic resonance frequency of sensor. If the magnetic field which is applied in sensor material is removed, magnetization made by magnetic field is transited to elastic mode. moreover. energy radiation is induced during the transition and voltage generates in sensor by energy radiation. At this moment, If voltage generation period is longer, mechanical vibration is induced and signal is generated by mechanical vibration. we also see that as the increase of thin film sensor' length and width, magnetic resonance frequency is decreased.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2007.06a
/
pp.33-33
/
2007
SoP-L 공정은 유전율이 상이한 재료를 이용하여 PCB 공정이 가능하고 다른 packaging 방법에 비해 공정 시간과 비용이 절약되는 잠정이 있다. 본 연구에서는 SoP-L 기술을 이용하여 Si 기판의 함몰에 판한 공정의 안정도와 함몰 시 제작된 때턴의 특성의 변화에 대해 관찰 하였다. Si 기판의 함몰에 Active device를 이용하여 특성의 변화를 살펴보고 공정의 안정도를 확립하려 했지만 Active device는 측정 시 bias의 확보와 특성의 민감한 변화로 인해 비교적 측정이 용이하고 공정의 test 지표를 삼기 위해 passive device 를 구현하여 함몰해 보았다. Passive device 의 제작 과정은 Si 기판 위에 spin coating을 통해 PI(Poly Imide)를 10um로 적층한 후에 Cr과 Au를 seed layer로 증착을 하였다. 그리고 photo lithography 공정을 통하여 photo resister patterning 후에 전해 Cu 도금을 거쳐 CPW 구조로 $50{\Omega}$ line 과 inductor를 형성하였다. 제작 된 passive device의 함몰 전 특성 추출 data와 SoP-L공정을 통한 함몰 후 추출 data 비교를 통해 특성의 변화와 공정의 안정도를 확립하였다. 차후 안정된 SoP-L 공정을 이용하여 Active device를 함몰 한다면 특성의 변화 없이 size 룰 줄이는 효과와 외부 자극에 신뢰도가 강한 기판이 제작 될 것으로 예상된다.
Kim, Jun-Young;Song, Dae-Ho;Lee, Yong-Kyun;Park, Tae-Jin;Kwon, Soon-Kab;Kang, Mun-Hyo;Lee, Sun-Hee;Han, Seung-Hoon;Cho, Sang-Mi;Kim, Jun-Hee;Jang, Jin
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2005.05a
/
pp.84-87
/
2005
본 논문에서는 p-type 고분자 물질인 P3HT (Poly-3-hexylthiophene)를 잉크젯 프린팅 방식으로 활성화층을 적층함으로써 Organic thin film transistor를 제작하여 이에 대한 특성을 연구하였다. Piezoelectric 방식의 잉크젯 프린팅을 이용하여 P3HT single drop jetting 시 두께 $150{\sim}200{\AA}$, 직경 약 70 ~ 80 um정도의 drop profile을 얻을 수 있었다. P3HT의 solvent로서 Chlorobenzene을 사용하여 농도 약 0.5 wt.%의 Ink-jet용 ink를 제작하여 이를 Channel Width 37, 236 um 크기의 Au 전극 위에 jetting 하여 각각의 특성을 측정하였다. 상기 실험은 상온의 외부환경에서 실시되었으며 실험 결과 최대 ${\mu}=1{\times}10^{-2}\;cm^2/Vsec$, $I_{on}/I_{off}=10^3{\sim}10^4$ 정도로서 off current가 높은 편이나 이동도 측면에서는 다른 방법의 박막 증착 실험결과와 비교할 때 동등 수준의 결과를 얻을 수 있었다.
In this work, we investigated the role of oxygen annealing on the performance of Metal-Semiconductor-Metal (MSM) UV photodetector (PD) fabricated by radio frequency (RF)-sputtered Ga2O3 films on SiC substrates. Oxygen-nnealed Ga2O3 films displayed a notable increase in photocurrent and a faster decay time, indicating a decrease in persistent photoconductivity. This improvement is attributed to the reduction of oxygen vacancies and variation of defects by oxygen post-annealing. Our findings provide valuable insights into enhancing PD performance through oxygen annealing.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.