• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.6
• /
• pp.669-675
• /
• 2011

A constant hanger is a device for supporting pipes in plants. It supplies a constant force to a supporting pipe even if the pipe moves because of thermal expansion. In this paper, we propose a method for designing the contour of a cam for a constant hanger. It has been shown that the contour of a cam must satisfy the geometrical relation of the cam, the force balance equation for the load tube, the relation between the side spring compression and the cam rotation angle, and the moment balance equation for the cam. A calculation procedure to solve these equations simultaneously is proposed, and a constant hanger is designed successfully.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.745-748
• /
• 2008

The past structures were just required bearing capacity to service load, serviceability, and resistance to corrosion. However this point of view has changed after 9.11 terrorism, capacities which can bear impact loading by explosion, and heat by fire happening at the same time, become to be important as a basic condition. The blast resistance capacity of structures is very important part against all over the world is intimidated by terrorism everyday in current point of time. The target of this research is a development of segmented composites and layered structures with high blast resistance using cementitious composites, concrete and FRP composites, which has high tensile strength and ductility, to apply in not only existing facilities but also new ones. Through the improvement of blast resistance, casualties and economic loss can be minimized, and it is possible to diminish the structure collapse and delay the time of structure collapse by thermal effect, impact loading, dynamic loading and high strain.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.49-59
• /
• 2003

The factors affecting the vertical loads acting on embankment piles can be classified into two factors on pile and soil. Factor on pile is the space between pile cap and factors on soil are embankment height and soil parameters(c, $\phi$). Therefore, a series of model tests were performed both to investigate the extent of influence of these factors and to verify the reliability of the proposed theoretical analysis. In the model tests, the piles were installed in the 6 columns $\times$ 6 rows(or 5 columns $\times$ 5 rows) below the embankment and the isolated pile caps with the area of 2.5cm $\times$ 2.5cm were installed on each pile head. The portion of the embankment load carried by model pile caps decreases with increment of the space between pile caps and increases with increment of the embankment height and the relative density(or internal friction angle) of fill. Also, the experimental results showed good agreement with theoretical predictions.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.347-354
• /
• 2012

The recovery force and displacement occur due to the phase transformation from the martensite phase to the austenite phase induced by the mechanical loading or thermal loading. These recovery force and displacement depend on an initial geometrical configuration of SMAs and loading conditions. Although the SMAs generally generates large recovery forces, the sufficient recovery displacement cannot be expected without a proper design strategy. The functionality of SMAs is limited due to the unbalance between the large recovery force and the small recovery displacement. This study suggests the double coil SMA spring in order to amplifying the recovery displacement induced by the phase transformation. By predicting the recovery displacement of doble coil SMA springs and one coil SMA springs induced by thermal loading, we show that the double coil SMA spring not only mitigate the unbalance of performance but also have a large recovery displacement for its recovery force than one coil SMA spring.

• Composites Research
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2008

Rubber hose assembly for automotive hydraulic brake during operation is subject to combined stresses of cyclic pressure, cyclic bending and torsion as well as thermal load. The rubber hose is composed of ethylene-propylene diene monomer(EPDM) rubber layers reinforced by polyvinyl acetate(PVA) braided fabrics. A durability tester with loading rigs for inducing the above cyclic stresses was used to investigate failure mechanisms in the rubber hose assembly. Failure examination was performed at every 100 thousands cycles of bending and torsion. Hose samples were sectioned with a diamond-wheel cutter and then polished. The polished surface was observed by optical microscope and scanning electron microscope (SEM). Some interfacial delamination with a length of about 1mm along the interface between EPDM rubber and PVA fabrics was shown at the test cycles of 400,000. The delamination induced some cracking into the outer rubber skin layer to leading the final rupture of the hose.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.193-205
• /
• 2001

In this study the behavior of pile groups is investigated experimentally. Special attention is given to the load transfer characteristics of pile groups and to the evaluation of the group effects under vertical and horizontal loadings. In the laboratory experiments, vertical and lateral loadings were imposed on model piles in sand. Model piles made of PVC embedded in Joomoonjin sand were used in this study. Pile arrangements($2\times2,\; 3\times3$) and pile spacings(2.5D, 5.OD, 7.5D) were considered. Load-transfer curves(t-z, q-z and p-y curves), load-deflection curves and group interaction factors were obtained from the experimental results. The group interaction factors under both vertical and horizontal loadings were proposed for the cases of $2\times2\; and\; 3\times3$ pile groups with varying ratios of pile spacings. p-multipliers in this study were found for the individual piles in $2\times2\; and\; 3\times3$ pile groups.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.4
• /
• pp.71-82
• /
• 1999

An axisymmetric shell element which includes the effects of the meridional and circumferential cable prestresses is developed. The fluid-structure interaction is expressed as added mass effect which is in proportion to the acceleration of the structure in interface surface. The added mass is obtained by using finite element method under the assumption that the fluid is invicid, incompressible and irrotational. It is coded for personal computer by the maximum use of axisymmetic properties and the dynamic analysis are performed under seismic exitations. A ring element makes the characteristics of the axisymmetric shell to be fully utilized. The elgenvalue solutons under the initial prestresses and the internal fluid are well agreed with the exact solutions and references by using under 20 elements. The eigenvalues are decreased along the increasing the height of internal fluid and these effects are dominant under the lower wave numbers. The results of the seismic analysis show that the radial deflection under the meridional prestress is a little larger than that under the circumferential prestress.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.221-229
• /
• 2001

The mechanical stress due to the wheel-rail contact and thermal stress due to the drag braking increase the incidence of wheel failure. So, firstly, stress analyses(mechanical, thermal and combined stress) of wheel plate are performed using 3-dimensional finite element method(FEM). Secondly, the optimum design of wheel plate ;s investigated in order to reduce weight of the wheel based on results of stress analysis. The optimum design is peformed using 2-dimensional axisymmetric F.E. model and its results are verified by 3-dimensional F. E. model.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.1
• /
• pp.77-85
• /
• 2001

본 연구에서는 차량하중에 의한 상시진동기록을 이용한 교량의 손상추정기법을 연구하였다. 즉, 차량진행 중 측정된 신호로부터 구조물의 모드특성을 구하고, 이를 이용하여 손상위치 및 손상정도를 추정하는 알고리즘을 제안하였다. 제안기법의 검증을 위하여 차량하중을 재하할 수 있는 모형교량을 제작하여 손상실험을 수행하였다. 차량진행 중 교량의 수직가속도를 계측하였으며, 측정된 가속도시계열로부터 random decrement(RD) 기법을 사용하여 자유진동신호를 구한 후, 이로부터 구조물의 모드특성을 추정하였다. 추정된 모드특성을 기초로 신경망기법을 적용하여 손상위치 및 손상정도를 추정하였으며, 추정된 결과는 실제 손상과 비교적 잘 일치하였다.

• Journal of the KSME
• /
• v.33 no.7
• /
• pp.636-647
• /
• 1993

평판과 셸은 그 하중 지지의 효율성 때문에 각종 구조물에 널리 사용되고 있다. 그러나 여러 종류의 불연속은 어쩔 수 없이 존재하게 된다. 대형 구조물의 출입을 위한 개구부의 존재나, 관과 노즐의 결합 부위 등 복잡한 형상을 가지면서 생기는 기하학적 문제, 재료에 원래 존재하는 균 열이나 개재물(inclusion) 등의 문제가 그 예가 될 것이다. 집중하중이나 선하중 등은 넓은 의미의 불연속으로서 힘에 의한 것으로 볼 수 있으나, 보다 문제가 되는 것은 변위의 불연속으로 이해될 수 있는 균열의 문제일 것이다. 이균열의 존재는 구조물의 안전성에 미치는 효과가 커서 중요한 연구 대상이 되어 있다. 또 해석적 방법으로 풀기도 까다로운데, 여기서는 이 문제를 다루는 해 석적 방법들을 살펴보고, 또 효율적으로 계산할 수 있는 반해석적(semi-analytical) 방법을 도입한 수 대표적인 평판과 셸 문제를 예로 들어본다.