• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.722-728
• /
• 2015

The demand for shipboard energy management is expected to gradually increase based on ship energy efficiency management plans (SEEMPs), which have been in use since January 1, 2013. Therefore, the fuel consumption of the main engine, which occupies the greatest portion of the energy used, along with elements related to the engine power, should be strictly monitored. There are many different methods for indicating the engine power. However, this study performed an experiment to monitor the status of a ship's engine power in real time using an encoder and a proximate switch, which are economical to purchase and easy to install. In the experiment, the angular velocity during one cycle of a two-stroke low-speed engine was measured, and the measured data were converted to the torque fluctuation. The angular velocity during an abnormal firing condition in the cylinder was also measured, and the torque fluctuation as a result of a misfire was considered. The results were compared with sea trial data to determine the reliability. In this study, the status of the engine power was determined using the torque fluctuation of the main engine in an operating ship.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.148-154
• /
• 2005

As the exciting point of each phase is determined by the position of rotor, the rotor's accurate position-information is needed for the Switched Reluctance Motor(SRM). When using an absolute-encoder or a resolver, to detect the location of rotor the initial starting is possible, as early sensing of rotor's location is possible. However, this is not appropriate, considering the economical efficiency, and in case of using the incremental-encoder, there's a problem at initial starting as it is not easy to track down the location of rotor at the very beginning. When using Hall-ICs, there's a fault, as it needs a special ring magnet. Considering the initial starting and economical efficiency, the optical sensor technique using a slotted-disk and an opto-interrupter is appropriate, however, this method needs three opto-interrupters and a slotted-disk when using the 6/4 pole SRM. Nevertheless, in this paper, it used only two optical sensors to operate 6/4 pole SRM and made the start up and also forward and reverse operation possible. By excluding the slotted-disc md shortening a optical sensor, it improved the convenience and economical efficiency of the production. Also, as the space for slotted-disc is no more needed, it was able to reduce the size of motor.

• Journal of KIISE:Computing Practices and Letters
• /
• v.10 no.4
• /
• pp.309-318
• /
• 2004

This paper proposes the H.264-based selective fine granular scalable (FGS) coding scheme that selectively uses the temporal prediction data in the enhancement layer. The base layer of the proposed scheme is basically coded by the H.264 (MPEG-4 Part 10 AVC) visual coding scheme that is the state-of-art in codig efficiency. The enhancement layer is basically coded by the same bitplane-based algorithm of the MPEG-4 (Part 2) fine granular scalable coding scheme. In this paper, we introduce a new algorithm that uses the temproal prediction mechanism inside the enhancement layer and the effective selection mechanism to decide whether the temporally-predicted data would be sent to the decoder or not. Whenever applying the temporal prediction inside the enhancement layer, the temporal redundancies may be effectively reduced, however the drift problem would be severly occurred especially at the low bitrate transmission, due to the mismatch bewteen the encoder's and decoder's reference frame images. Proposed algorithm selectively uses the temporal-prediction data inside the enhancement layer only in case those data could siginificantly reduce the temporal redundancies, to minimize the drift error and thus to improve the overall coding efficiency. Simulation results, based on several test image sequences, show that the proposed scheme has 1∼3 dB higher coding efficiency than the H.264-based FGS coding scheme, even 3∼5 dB higher coding efficiency than the MPEG-4 FGS international standard.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.6-6
• /
• 2009

자동차 운반용 선박(PCTC) 건조 시, 자동차를 고정시키기 위해 약 5 만 여개의 Lashing Socket(6,700 Units PCTC 기준)이 소요되는데, 이때 사용되는 Lashing Socket 은 용도 및 형태에 따라 Hole Cup, Flush Cloverleaf Type Pot, Raised Cloverleaf Type Pot, D-Ring, Crinkle Bar 등으로 구분된다. 이와 같이 다양한 종류 중에서 Hole cup 타입이 전체 적용되는 Lashing Socket 의 약 80%에 이른다. 기존에 사용되고 있는 자동용접장치는 Hole Cup 이외에는 적용이 불가능하고, 자석을 이용하여 Hole Cup 의 상부에 위치시키는 방식이었기 때문에 경량화 및 다양한 종류 및 크기의 Lashing Socket 에 적용이 가능한 자동용접장비의 개발이 요구되었다. 본 연구에서는 두께가 다른 $\phi$140 Hole Cup 및 Flush Cloverleaf Type Pot, Raised Cloverleaf Type Pot 에 적용 가능하며, 분리형 용접캐리지와 Centering Template, Magnet Jig 로 구성된 연속 및 단속 용접이 가능한 자동용접장치를 연구 개발하였다. 이를 통해 종래 Hole Cup 전용 자동용접 캐리지의 문제점을 개선하여, 작업자가 Centering Template 과 Magnetic Jig 을 이용하여 캐리지를 Hole Cup 의 중앙에 위치시키기 용이하게 하였다. 이 같은 분리형 장치 구성을 통해 Hole Cup 중앙에 캐리지 고정 작업과 용접 작업을 분리함으로써 자동용접이 진행되는 도중에 여분의 Jig를 이용하여 다른 Hole Cup 에 용접 준비를 하여 연속적인 작업이 가능하도록 하였다. 본 연구는 종래의 Hole Cup 전용 자동용접 캐리지의 문제점을 개선한 분리형 용접 캐리지를 개발함으로써 아래와 같은 결과를 얻었다. 1. 용접 캐리지를 포함하여 각 부분별 분리를 통해 작업자가 1 회 이동 시 필요로 하는 중량을 감소시켜 장비의 이동 및 제어가 쉽다. 2. Magnetic Jig 를 Centering Template 에 결합하고, Template 의 Jig 를 Lashing Socket 에 결합함으로써 손쉽게 Lashing Socket 의 중심부를 찾을 수 있으므로 용접 캐리지의 정확한 센터 고정이 가능하다. 3. 엔코더에 의한 1 회전을 검출함으로써, 작업 종료 후, 어떤 위치에서나 작업 재개가 가능하며 원점 복귀 작업이 불필요하다. 또한 엔코더에 의한 거리 설정으로 용접 속도에 상관없이 동일한 거리만큼 오버랩 용접이 가능하다. 4 디지털 방식으로 용접 조건의 입력이 가능하고, 용접 조건을 D/B 화 함으로써 Control Panel 상에서의 자동 제어가 가능하다. 이를 통해 연속 용접 또는 단속 용접이 가능하므로 다양한 형태의 Lashing Socket 을 자동 용접할 수 있는 효과가 있다. 이상의 결과를 통해 본 장비가 Fig.2 의 3 가지 종류의 Lashing Socket 용접에 효과적인 장비임을 확인할 수 있었다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.1
• /
• pp.21-27
• /
• 2022

Traditional automobile or 2-wheeled robot have limitations on mobility because of their mechanical structure. As traditional automobile is being replaced by electric cars, robot technology is applied to the car industry. In robotics, many researchers worked on omnidirectional mobile robot and produced lots of noticeable results. However in many of the results, specialized wheels such as Mecanum wheels are required. That imposes restrictions on robot speed and outdoor driving. We proposed a 2-wheeled modular robot that has omnidirectional mobility without using specialized wheels. In this paper, we propose a 4-wheeled omnidirectional mobile robot that consists of those two modular robots. The proposed robot adopts electric brakes to combine wheel housings and the robot body or to separate wheel housings from the robot body. Two absolute-type encoders and four incremental encoders are used to control the position of the wheel housing and velocities of the wheels. The proposed robot has omnidirectional mobility and can move fast and outdoor with normal tire wheels. We implemented the proposed robot and the feasibility and stability of the robot is verified by two separate experiments.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.90-97
• /
• 1991

A stepping motor can be driven with open-loop or closed-loop control. The major disadvantage of open-loop control is that it is subjected to resonance and instability in certain speed range, and that there is no way to check stalling or error in position. In this paper, a closed-loop control system consisting of a microcomputer, a hybrid stepping motor, a drive, a lead screw, and an encoder which is used as a position sensor is developed. A control program is programmed in assembly language for real time control and the versatile interface adapter(VIA) is used as the interface with the microcomputer. The experimental results of the stepping motor were eliminated on all kinds of inertia load, and maximum start stop pulse rate and maximum slewing pulse rate were also increased about twice respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.193-193
• /
• 2009

Thin-type 초음파모터의 구조는 크로스형태의 앓은 스테이터에 윗면과 아랫면에 각각 8개의 압전세라믹이 부착된 형태이고, 압전세라믹의 분극방향은 로터와 접촉하는 스테이터의 중심부인 네 개의 타점에서 순차적인 타원변위가 생성되도록 결정된다. 유한요소해석프로그램인 ATILA 5.2.4를 사용하여 형태, 길이, 두께, 스테이터 재질, 클램프특성이 최적 설계된 모델을 제작하였고, 푸쉬풀 게이지, x-y 스테이지, rpm 메터, 토크 게이지, 맨코더, AD컨버터를 이용하여 피드백 제어 구동시스템을 구성하였다. 그림 I은 마이크로컨트롤러 (ATmega)와 피드백회로를 이용한 구동 드라이버를 보여준다. 한 주기에서 1/4분주의 순차적인 네 개의 구형파를 생성하고, 이를 push-pull회로를 통하여 90도의 위상차가 나는 정현파를 생성하여 초음파 모터의 구동전원으로 사용한다. 피드백 회로인 엔코더와 AD 컨버터는 초음파모터의 속도를 피드백하여 정속도 운전을 위한 전압제어에 사용되었다. 특성 측정 결과, 제품화된 드라이버와 비교하여 큰 차이를 보이지 않았고 피드백 회로를 통하여 부하변화에 따른 속도의 극심한 변화를 0.2~0.4[N]의 범위에서 정속도 운전이 가능하였으며, 장시간의 운전에도 온도 및 속도특성이 안정적임을 확인하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.4
• /
• pp.412-417
• /
• 2014

This paper presents the development and control of an omni-directional holonomic mobile robot platform, which is equipped with three lateral orthogonal-wheel assemblies. Omni-directionality can be achieved with decoupled rotational and translational motions. Simulation studies on collision avoidance are conducted. A real robot is built and its hardware is implemented to control the robot. Control algorithm is embedded on DSP and FPGA chips. Hardware for motor control such as PWM, encoder counter, serial communication modules is implemented on an FPGA chip. Experimental studies of following joystick commands are performed to demonstrate the functionality and controllability of the robot.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.77-84
• /
• 2013

In this paper, we review two-dimensional measuring methods referring to target patterns. The patterns consist of two linearly-repeated patterns or is designed repeatedly in two-dimension. The repeated properties are reflectivity, refractivity, air-gapping distance, capacitance, magnetic reluctance, electrical resistance and sloping gradient, etc. However, the optical methods are generally used for high speed processing and density, and their encoding principles are treated here. In case of two-dimensional pattern, as there is not inherently error between single units encoding the pattern except for the metrology frame errors, the end-effector position of an object accompanying the pattern can be measured with respect of the global frame without via error. Therefore, it is regarded as a substitute for laser interferometer with severe environmental constraints and has been applied to the high-accurate planar actuator.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.5 s.236
• /
• pp.770-776
• /
• 2005

The gains fur NC controller parameter are fixed when the controller is combined with a machine. However, the characteristics of controller could be changed as it has being used by the machine or other environmental conditions. Those result in that the tool positioning accuracy is influenced. The loading torque in servo motor influences on the tool positioning accuracy and it is controlled by the parameter gains. It is required to analyze the torque variation with angular positioning accuracy of the servo motor. This study focus on a measuring method and device for verifying angular positioning accuracy of NC servo motor. We used a high resolution An converter for acquiring analogue signal of rotary encoder in servo motor. The positional accuracy for a nominal tool path, which is generated by the combination of axial movements (X,Y,Z), is analyzed with the servo motor torque. The current variation signal is acquired at the power line using a hall sensor and converted to the loading torque of servo motor. The method of measurement and analysis proposed in this study will be used for determining the gains of parameter in NC controller. This gain tuning is also necessary when the controller is set up at a machine.