• Korean Journal of Environmental Agriculture
• /
• v.41 no.2
• /
• pp.82-94
• /
• 2022

BACKGROUND: Spiropidion and its metabolite are tetramic acid insecticide and require the establishment of an official analysis method for the safety management because they are newly registered in Korea. Therefore, this study was to determine the analysis method of residual spiropidion and its metabolite for the five representative agricultural products. METHODS AND RESULTS: Three QuEChERS methods (original, AOAC, and EN method) were applied to optimize the extraction method, and the EN method was finally selected by comparing the recovery test and matrix effect results. Various adsorbent agents were applied to establish the clean up method. As a result, the recovery of spiropidion was reduced when using the dispersive-SPE method with MgSO₄, primary secondary amine (PSA), graphitized carbon black (GCB) and octadecyl (C₁₈) in soybean. Color interference was minimized by selecting the case including GCB and C18 in addition to MgSO₄. This method was established as the final analysis method. LC-MS/MS was used for the analysis by considering the selectivity and sensitivity of the target pesticide and the analysis was performed in MRM mode. The results of the recovery test using the established analysis method and inter laboratory validation showed a valid range of 79.4-108.4%, with relative standard deviation and coefficient of variation were less than 7.2% and 14.4%, respectively. CONCLUSION(S): Spiropidion and its metabolite could be analyzed with a modified QuEChERS method, and the established method would be widely available to ensure the safety of residual insecticides in Korea.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.23 no.2
• /
• pp.43-50
• /
• 2021

Growth tests on the Yuldo, Supum1 and Supum2 cultivars of Pyropia dentata were performed at the Eoran and Imha aquafarm, Haenam in Jeollanamdo, from October to December in 2017. The mean water temperature ranged from 5.4 to 26.4 ℃. In Eoran aquafarm (flating raft method), dissolved total nitrogen (DTN), dissolved total phosphorus (DTP), total nitrogen (TN), total phosphorus (TP) and chemical oxygen demand (COD) ranged from 0.091 to 0.181 mg/L, 0.007 to 0.019 mg/L, 0.114 to 0.187 mg/L, 0.008 to 0.033 mg/L and 0.200 to1.000 mg/L, respectively. In Imha aquafarm (fixed pold method), DTN, DTP, TN, TP and COD ranged from 0.118 to 0.276 mg/L, 0.005 to 0.024 mg/L, 0.155 to 0.305 mg/L, 0.009 to 0.042 mg/L and 0.300 to1.400 mg/L, respectively. In order to investigate the number of conchospores attached on the Pyropia net, which was cut into about 4cm long. The mean number of conchospores of Yuldo, Supum1 and Supum2 cultivars were 39.5, 26.5, 72.5, respectively. Young thalli were harvested two times at Eoran aquafarm, and three times at Imha aquafarm. In eoran aquafarm, the mean thallus length of Yuldo, Supum1 and Supum2 cultivars were 49.9, 46.0, 42.0 cm on October and 163, 126.0, 263.0 cm on November, respectively. The mean thallus width of Yuldo, Supum1 and Supum2 cultivars were 5.8, 4.6, 11.5 cm on October and 20.9, 11.5, 14.0 cm on November, respectively. In Imha aquafarm, the mean thallus length of Yuldo, Supum1 and Supum2 cultivars were 119.0, 60.9, 71.0 cm on October, 196.0, 132.0, 262.0 cm on November and 187.0, 281.0, 296.0 cm on December, respectively. The mean thallus width of Yuldo, Supum1 and Supum2 cultivars were 4.2, 3.4, 3.1 cm on October, 8.9, 6.2, 6.6 cm on November and 11.7, 11.6, 9.4 cm on December, respectively. In eoran aquafarm, contents of moisture, crude ash, crude lipid, crude protein and carbohydrate of three cultivars ranged from 11.64 to 20.15, 19.54 to 21.19, 0.00 to 0.18, 29.78 to 37.81, 29.16 to 29.71, respectively. In Imha aquafarm, contents of moisture, crude ash, crude lipid, crude protein and carbohydrate of three cultivars ranged from 8.43 to 9.15, 11.42 to 17.49, 0.00 to 0.00, 31.90 to 37.54, 36.30 to 42.24, respectively.

• The Journal of Korean Academy of Prosthodontics
• /
• v.60 no.3
• /
• pp.231-238
• /
• 2022

Purpose. This study aimed to investigate the effect of different veneering methods on the tensile bond strength between polyetherketoneketone (PEKK) and denture base resins. Materials and methods. A total of 80 PEKK T-shaped specimens were fabricated and the primer (Visio.link) was applied after airborne-particle abrasion with 110 ㎛ alumina oxide powder. According to the veneering method, the specimens were divided into four groups (n = 20) to be veneered with the gingival colored packable photopolymerized composite resin (SR Adoro); flowable photopolymerized composite resin, (Crea.lign); heat-polymerized resin (Vertex); and self-polymerized resin (ProBase Cold). Each group was divided into two subgroups (n = 10) according to the artificial thermal aging. After the tensile bond strength measurement via universal testing machine, the fracture sections of all specimens were observed. Two-way ANOVA and Tukey's HSD post hoc test were used for the statistical analysis (α = .05). Results. The results of the two-way ANOVA showed statistically significant differences in the tensile bond strength according to the veneering method and artificial thermal aging of denture base resins (P<.001). The highest tensile bond strength showed in the packable photopolymerized resin group before and after the artificial thermal aging. The lowest tensile bond strength showed in the heat-polymerized resin group. The mixed and adhesive fracture showed in all groups. Conclusion. The veneering method and artificial thermal aging can influence in the tensile bond strength between the resin and PEKK. The artificial thermal aging can reduce the tensile bond strength.

• Land and Housing Review
• /
• v.12 no.2
• /
• pp.33-45
• /
• 2021

Due to recent changes in government policy, officetels have received attention as alternative assets, along with the uplift of office and apartment prices in Seoul. However, the current officetel price indexes use small-size samples and, thus, there is a critique on their accuracy. They rely on valuation prices which lag the market trend and do not properly reflect the volatile nature of the property market, resulting in 'smoothing'. Therefore, the purpose of this paper is to create the officetel price index using transaction data. The data, provided by the Ministry of Land, Infrastructure and Transport from 2005 to 2020, includes sales prices and rental prices - Jeonsei and monthly rent (and their combinations). This study employed a repeat sales model for sales, jeonsei, and monthly rent indexes. It also contributes to improving conversion rates (between deposit and monthly rent) as a supplementary indicator. The main findings are as follows. First, the officetel price index and jeonsei index reached 132.5P and 163.9P, respectively, in Q4 2020 (1Q 2011=100.0P). However, the rent index was approximately below 100.0. Sales prices and jeonsei continued to rise due to high demand while monthly rent was largely unchanged due to vacancy risk. Second, the increase in the officetel sales price was lower than other housing types such as apartments and villas. Third, the employed approach has seen a potential to produce more reliable officetel price indexes reflecting high volatility compared to those indexes produced by other institutions, contributing to resolving 'smoothing'. As seen in the application in Seoul, this approach can enhance accuracy and, therefore, better assist market players to understand the market trend, which is much valuable under great uncertainties such as COVID-19 environments.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.11-18
• /
• 2021

A novel microwave dielectric composite material for ultra-low temperature co-fired ceramics (ULTCC) with (1-x)BaWO₄-xBaV₂O₆ (x=0.54~0.85) composition was prepared by firing a mixture of BaWO₄ and BaV₂O₆. Shrinkage tests showed that the ceramic composite begins to densify at a temperature as low as 550℃ and can be sintered at 650℃ with 98% of relative density under the influence of BaV₂O₆. X-ray diffraction analysis showed that BaWO₄ and BaV₂O₆ coexisted and no secondary phase was detected in the sintered bodies, implying good chemical compatibility between the two phases. Near-zero temperature coefficients of the resonant frequency (𝛕_f) could be achieved by controlling the relative content of the two phases, due to their positive and negative 𝛕_f values, respectively. With increasing BaV₂O₆ (x from 0.53 to 0.85), the 𝛕_f value of the composites increased from -7.54 to 14.49 ppm/℃, ε_r increased from 10.08 to 11.17 and the quality factor (Q×f value) decreased from 47,661 to 37,131 GHz. The best microwave dielectric properties were obtained for x=0.6 samples with ε_r=10.4, Q×f=44,090 GHz, and 𝛕_f=-2.38 ppm/℃. Chemical compatibility experiments showed the developed composites are compatible with aluminum electrode during co-firing process.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.651-662
• /
• 2022

The electrochemical impedance spectroscopy(EIS) method was used to evaluate the concrete deterioration process related to chloride-induced steel corrosion with various corrosion levels(initiation, rust propagation and acceleration periods). The impressed current technique, with four total current levels of 0C, 13C, 65C and 130C, was used to accelerate steel corrosion in concrete cylinder samples with w/c ratio of 0.4, 0.5, and 0.6, immersed in a 0.5M NaCl solution. A series of EIS measurements was performed to monitor concrete deterioration during the accelerated corrosion test in this study. Some critical parameters of the equivalent circuit were obtained through the EIS analysis. It was observed that the charge transfer resistance(R_c) dropped sharply as the impressed current increased from 0C to 13C, indicating a value of approximately 10kΩcm². However, the sensitivity of R_c significantly decreased when the impressed current was further increased from 13C to 130C after corrosion of steel had been initiated. Meanwhile, the double-layer capacitance value(C_dl) linearly increased from 50×10^-6μF/cm² to 250×10^-6μF/cm² as the impressed current in creased from 0C to 130C. The results in this study showed that monitoring C_dl is an effective measurement parameter for evaluating the progress of internal concrete damages(de-bonding between steel and concrete, micro-cracks, and surface-breaking cracks) induced by steel corrosion. The findings of this study provide a fundamental basis for developing an embedded sensor and signal interpretation method for monitoring concrete deterioration due to steel corrosion at various corrosion levels.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.7
• /
• pp.49-62
• /
• 2022

The hollow modular concrete block reinforced foundation method is one of the ground reinforcement foundation methods that uses hexagonal honeycomb-shaped concrete blocks with mixed crushed rock to reinforce soft grounds. It then forms an artificial layered ground that increases bearing capacity and reduces settlement. The hollow modular honeycomb-shaped concrete block is a geometrically economical, stable structure that distributes forces in a balanced way. However, the behavioral characteristics of hollow modular concrete block reinforced foundations are not yet fully understood. In this study, a bearing capacity test is performed to analyze the reinforcement effectiveness of the hollow modular concrete block through the laboratory model tests. From the load-settlement curve, punching shear failure occurs under the unfilled sand condition (A-1-N). However, the filled sand condition (A-1-F) shows a linear curve without yielding, confirming the reinforcement effect is three times higher than that of unreinforced ground. The bearing capacity equation is proposed for the parts that have contact pressure under concrete, vertical stress of hollow blocks, and the inner skin friction force from horizontal stress by confining effect based on the schematic diagram of confining effect inside a hollow modular concrete block. As a result of calculating the bearing capacity, the percentage of load distribution for contact force on the area of concrete is about 65%, vertical force on the area of hollow is 16.5% and inner skin friction force of area of the inner wall is about 18.5%. When the surcharge load is applied to the concrete part, the vertical stress occurs on the area of the hollow part by confining effect first. Then, in the filled sand in the hollow where the horizontal direction is constrained, the inner skin friction force occurs by the horizontal stress on the inner wall of the hollow modular concrete block. The inner skin friction force suppresses the punching of the concrete part and reduces contact pressure.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.67 no.4
• /
• pp.319-325
• /
• 2022

Triticale forage has the highest yield of all winter forage crops, including rye, and a cold tolerance within an average low temperature of -10℃ in January. Therefore, this study analyzed the effects of sowing and harvesting times on the feed value and functional components of triticale to optimize the use and supply of triticale as livestock fee Room temperature' can vary widely with climate, season, and time of day. In order to clearly state the conditions of the study in a manner that facilitates replication by other researchers, please consider using an approximate temperature range instead. Seeds of the triticale 'Joseong' were sown during the fall of 2021 (October 20th) and spring of 2022 (March 7th). The triticale was harvested at the following growth stages: seedling stage, booting stage, heading stage, 10 days after heading, and 20 days after heading. The moisture content of each harvested triticale was adjusted to approximately 60%, and the triticale was fermented for silage for 40 days at ambient temperature under anaerobic conditions. We measured the pH and organic acid content of each silage to determine the feed value and functional component. The lactic acid content of the triticale silage harvested at the seedling stage sown in both fall and spring (1.61%, 1.63%) was the highest among all the silages. The octacosanol content in the silages of both fall-sown and spring-sown triticale harvested at the seedling stage (0.38, 0.27 mg/ml) was the highest. Overall, the results revealed that harvesting time had a greater impact on the feed value and functional components of triticale silage than sowing time.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.67 no.4
• /
• pp.199-210
• /
• 2022

This study aimed to develop a cropping system to use limited crop-land with optimum efficiency, while considering management from farmers. To establish the cropping system involving a two-year rotation of three crops, three types of cropping system were evaluated in Suwon (Seogcheon series) and Anseong (Geumcheon series) in the middle plain area using six crops from 2018 to 2019: maize-perilla-onion, potato-sesame-garlic, and maize-sesame-onion. The crop productivity and income of the cropping systems involving food-, oilseed-, and horticultural crops were analyzed, and the optimal cropping system was reviewed. The total yield of each crop was as follows: maize 1,281 kg, potato 4,837 kg, perilla 125 kg, sesame 120 kg, onion 6,503 kg, and garlic 1,027 kg per 10a. However, in terms of gross profit, the potato was more than 3.8 times more profitable than corn, sesame was 1.8 times more profitable than perilla, and garlic was more than 2.8 times more profitable than onions. As a result, in terms of net income, the potato-sesame-garlic cropping system produced the highest income per unit area. Sesame seedlings were planted after the potato harvest, thereby solving the problem of competition between the first and last crops. Overall, this study confirmed that the potato-sesame-garlic cropping system, a two-year rotation of three crops, contributed to the improvement of upland crop productivity and farmers' income and was an overall effective cropping system.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.1
• /
• pp.20-26
• /
• 2023

Fiber content in the storage roots of sweetpotato varies between different varieties. For examples, the high fiber content of certain types has a poor texture when steamed or roasted. This study was conducted to evaluate the optimal sieve mesh size for separating fibers, the chemical composition of fibers and differences in fiber content among different varieties. We found that the separated fiber content (dry weight) of mashed and steamed sweetpotato was higher after washing three times (143.3 mg/100 g) compared with that washed five times (128.4 mg/100 g). The Hogammi variety remained 85.9% of total fiber content at 10 mesh (2,000 ㎛) and 9.6% of total fiber content at 30 mesh (600 ㎛), and Jinyulmi remained 74.9 and 16.7% of total fiber content , respectively. Therefore, a 30 mesh sieve was considered the most suitable for fiber separation. Among the 10 studied cultivars, Jinhongmi showed the lowest amount of fiber (24.8 mg/100 g) and Hogammi had the highest amount (111.4 mg/100 g), which was 4.5 times larger than that of Jinhongmi. Cellulose, hemicellulose and lignin content of separated fibers showed no difference between the viscous-type Hogammi and powdery-type Jinyulmi varieties, with averages of 32.5, 22.3 and 29.6%, respectively. Correlation results using the Image J program showed a significant correlation between the distribution of the stained area and the fiber content (R = 0.74, p < 0.05). Staining distribution differed among varieties, suggesting that a simple fiber content test could be performed using the staining method on raw sweetpotato. These results provide useful information to help inform farmers on the fiber content of different sweetpotato varieties.