• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1024-1028
• /
• 2006

The Fe-Mn damping Alloys which combine a high damping capacity with good mechanical properties can provide attractive technical and economic solutions to problems involving fatigue, noise and vibration. This study is aimed at finding its applicability to divided spherical bearing in bridge. The results obtained are summarized as follows : 1) The specific damping capacity of the Fe-Mn damping alloy is superior to that of SM490B. 2) The divided spherical bearing manufactured Fe-Mn damping alloy passes the load test to confirm applicability of that in bridge.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.174-177
• /
• 2003

Comparisons of measuring apparatus for sound insulation are made between a reverberation chamber and a simplified test apparatus(APAMAT II) that is used to measure sound insulation performance of inner panels for automobiles. Also, theoretical prediction by using sandwich model are made in order to compare it with experiments and to consequently provide a design tool. Comparative results show that steel ball excitation in APAMAT II has a serious problem with sound insulation performance at the low frequency region, while speaker excitation gives a good agreements with theoretical prediction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.581-586
• /
• 2000

Explosively activated pyro-technic device is used to release exhausted rocket booster or payloads at prescribed times in the rocket's flight. It creates pyro-shock environment that rocket or payload components must survive. With the shock spectra acquired from flight data, laboratory test should be performed before flight to check whether all of component can sustain the shock environment. The pyro-shock environment simulation was created by the resonance fixture response to a projectile impact. Desired shock spectra is realized by adjusting the natural frequency of resonance plate and the velocity of impact hammer. This paper describes the development process of Pyro-shock testing machine, which is designed and tested by Korean engineers, to verify components of Korean Sounding Rocket(KSR-3) and the other Korean space vehicle. Both analytical and experimental techniques are introduced in this paper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.692-697
• /
• 2005

A canard type aircraft, which has good wing stall and stall/spin proof characteristics, is being developed. The previous first and second prototypes, having full depth core sandwich type wing and fixed landing gear, was built for test flights. Newly developing Firefly will be equipped with retractable landing gear and conventional foam core sandwich laminate for wing and fuselage. For manufacturing, composite material process has been studied including coupon tests. Wet lay-up onto foam core with glass fabric using lay-up mold has been chosen, and composite material parts are cured under room temperature and atmospheric pressure condition. In general, molded parts show so good surface smoothness and standardized quality that are best in mass production. In this study, we present the mold technology and development status for small aircraft firefly.

• Explosives and Blasting
• /
• v.23 no.3
• /
• pp.83-89
• /
• 2005

It follows in deterioration of the steel frame structure and becomes remodeling and removal. The construction work characteristic, economical efficiency and stability environment characteristic are planned and considered hereafter control plan of the steel frame structure which is deteriorated currently to cutting mettled plentifully sued on gas cutting of H beam. However it will not be able to apply from the explosives demolition which is makes a weak instantaneously and then collapses the building at the time. In this study, shape charge was used for cutting of the H-beam. That is the element testing to estimate explosives demolition for steel frame structure. As a result, it is found for single-side rutting method, both-sides rutting methods by H-beam thickness and pre-rutting process. It confirmed an affix method and an ease characteristic by fixing tool. Also, it is shown that air blasting decreased about 8dB(A) in order to reduce air blasting used by sand box. However, it will be required to reduce air blasting little more because explosives demolition will be done in urban site.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.613-620
• /
• 1999

Brake judder{or cold judder) caused by the disc thickness variation(DTV) is investigated experimentally, This cold judder is often perceived by steering wheel vibration, brake pedal pulsation, and vehicle body vibration. In this paper, how the DTV profile affects the vibration characteristics of vehicle body is shown by order tracking analysis(OTA) and operational vibration analysis(OVA) The tri-axial vibrations are measured at the knuckle, lower rm, and the body side of the lower arm. Also, measured are the wheel speed and the detail DTV profile. The interpretations of OTA results in three directions of tested vehicle indicate the relative importance in the contribution of the run-out and the DTV to the judder vibration. Also, the OVA results show the prominent vibration amplitude of the lower arm in the direction of the vehicle movement. in which the second order of wheel speed is dominant. These results could be used to diagnose the judder problem and to establish the correction methods.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.12
• /
• pp.33-43
• /
• 2006

Driving tests using model plastic piles with different hammer cushion materials were performed in order to evaluate the efficiency of energy transfer ratio from the hammer, degree of vibration of the surrounding ground and noise due to impacting. A small pile driving analyzer (PDA) was composed using straingages and Hopkinson bar which is measuring force signal and pile-head velocity. The hammer cushion (cap block) materials used for the model driving tests were commercial Micarta, plywood, polyurethane, rubber (SBR) and silicone rubber. The highest energy transfer ratio was obtained from Micarta in the same soil and driving conditions. Micarta was followed by polyurethane, plywood, rubber and silicone in descending order. The more efficient energy transfdr ratio of the hammer cushion materials became, the bigger average noisy (sound) level was found. In addition, Micarta and polyurethane provided bigger bearing capacities than other materials compared in the same soil and driving conditions in which the static loading tests were performed at the end of driving.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.52-52
• /
• 2000

저진공 펌프 제작시 ISO, AVS 등의 국제규격에 ？춤은 필수이고, 도달진공도, 압력구간별·가스별 배기속도, 소음, 기름증기 역류, 압축비 등이 이에 해당된다. 큰 체적의 시험용기가 구비되어 있지 않은 경우에는 배기감압법 대신 일정유량 Q를 흘려 시험용기내에 일정압력 P를 유지시키면서 배기속도를 S=Q/P식으로 구하는 일정압력법을 사용한다. 이 실험은 800~2000 l/min급 유회전 펌프와 드라이 펌프로 압력별 배기속도를 측정, 분석하여 평가방법을 수립하였다. 또 국가 유량 표준기인 sonic nozzle을 reference로 하여, 기존의 유량측정 장비와의 오차를 비교하였다. 온도 상승도를 측정, 압력과의 상관관계를 비교하였고, 오차가 적은 CDG(1, 10, 100torr)를 사용하여, 압력측정의 정확도를 높였다. 비교적 outgassing이 적은 SUS 재질의 chamber를 썼고, 유량조절 장치로 미세누출밸브를 사용하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.7
• /
• pp.645-653
• /
• 2013

Seoul National University flap(SNUF) blade is a small-scale rotor blade incorporating a small trailing-edge flap control surface driven by piezoelectric actuators at higher harmonics for vibration attenuation. Initially, the blade was designed using two-dimensional cross-section analysis and geometrically exact one-dimensional beam analysis, and its material configuration was finalized. A flap-deflection angle of ${\pm}4^{\circ}$ was established as the criterion for enhanced vibration reduction based on an earlier simulation. The flap-linkage mechanism was designed and static bench tests were conducted for verifying the performance of the flap-actuation mechanism. Different versions of test beds were developed and tested with the designed flap and the selected APA 200M piezoelectric actuators. Through significant improvements, a maximum deflection of ${\pm}3.7^{\circ}$ was achieved. High-frequency experiments were conducted for evaluating the performance, and the transfer function of the test bed was determined experimentally. With the static tests almost complete, the rotor power required for testing the blade in a whirl tower (centrifugal environment) was calculated, and further preparations are underway.

• 대한공업교육학회지
• /
• v.31 no.1
• /
• pp.211-225
• /
• 2006

Gabion can be used for the purpose of preventing overflow of river and side loss of road. However the manufacturing process of the gabion is manually controlled especially to the joining process at the terminal part of gabion with small diameter wire. In this paper automatic feeding guide system was designed and fabricated to make automation. The fabricated system was tested in the factory level. Pneumatic system was considered as the main idea of the feeding system. 3/2-way and 5/2-way manual control valve, eight double-acting cylinders were used. The system took 46.48 seconds during a cycle. Additional environmental noise and vibration were not detected when the machine operated at the working area. Based on the theoretical simulation and actual test the fabricated system was well controlled. The system was applied to the patent in 2006.