• Journal of the Korean Geotechnical Society
• /
• v.31 no.1
• /
• pp.53-64
• /
• 2015

This study presents the experimental results of pervious blocks subjected to a series of unique inflow conditions in urban area. The measured properties include the strength, permeability, drainage capacity and runoff, and evaporation for blocks made of two different size of aggregates. Results revealed that the strength satisfies the Korean Standard regardless of aggregate size whereas the immediate runoff occurred for the block with small size aggregate. On the other hand, the block with large aggregates allowed the drainage upon the initial inflow condition, which became hampered to induce the runoff by subsequent inflow. It was attributed to the fact that the capillary water often served as the hydraulic barrier in partially saturated condition. The salient observation indicated that the runoff highly depended on the evaporation and pre-wetting condition as well as the porosity and pore connectivity. The bilinear evaporate rate that makes the degree of saturation vary also had great influence on deterining the time-dependent runoff.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.4 s.334
• /
• pp.29-36
• /
• 2005

This paper presents the first hardware design of ARIA that KSA(Korea Standards Association) decided as the block encryption standard at Dec. 2004. The ARIA cryptographic algorithm has an efficient involution SPN (Substitution Permutation Network) and is immune to known attacks. The proposed ARIA design based on 1 cycle/round include a dual port ROM to reduce a size of circuit md a high speed round key generator with barrel rotator. ARIA design proposed is implemented with Xilinx VirtexE-1600 FPGA. Throughput is 437 Mbps using 1,491 slices and 16 RAM blocks. To demonstrate the ARIA system operation, we developed a security system cyphering video data of communication though Internet. ARIA addresses applications with high-throughput like data storage and internet security protocol (IPSec and TLS) as well as IC cards.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.7 s.349
• /
• pp.50-57
• /
• 2006

Low-density parity-check (LDPC) codes are recently emerged due to its excellent performance. However, the parity check (H) matrices of the previous works are not adequate for hardware implementation of encoders or decoders. This paper proposes a hybrid parity check matrix which is efficient in hardware implementation of both decoders and encoders. The hybrid H-matrices are constructed so that both the semi-random technique and the partly parallel structure can be applied to design encoders and decoders. Using the proposed methods, the implementation of encoders can become practical while keeping the hardware complexity of the partly parallel decoder structures. An encoder and a decoder are designed using Verilog-HDL and compared with the previous results.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.359-365
• /
• 2006

Wave-front error(WFE) is the main parameter that determines the optical performance of the opto-mechanical system. In the development of opto-mechanics, WFE due to the main loading conditions are set to the important specifications. The deformation of the optical surface can be exactly calculated thanks to the evolution of numerical methods such as the finite element method(FEM). To calculate WFE from the deformation results of FEM, another approximation of the optical surface deformation is required. It needs to construct additional grid or element mesh. To construct additional mesh is troublesomeand leads to transformation error. In this work, the moving least-squares approximation is used to reconstruct wave front error It has the advantage of accurate approximation with only nodal data. There is no need to construct additional mesh for approximation. The proposed method is applied to the examples of GOCI scan mirror in various loading conditions. The validity is demonstrated through examples.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.1
• /
• pp.17-21
• /
• 2005

Shielded laser ablation system composed of laser system, image analyser, XYZ translator with motion controller, ablation chamber, manipulator and various optics was designed. Nd:YAG laser which can be tunable from 1064 nm to 266 m was selected as light source. CCD camera(< $\pm$200) was chosen to analyze a crater less than 50 un in diameter. XYZ translator was composed of three linear stage which can travel 50 w with a minimum movement of 1 um and motion controller. Before the performance test, each part of system was optically aligned. To perform the ablation test, the specimen was ablated by 50 um interval and observed by image analyser The shape of crater was almost round, indicating laser beam has homogeneous energy distribution. The resolution and magnification of image system were compatible with the design.

• Particle and aerosol research
• /
• v.7 no.3
• /
• pp.87-97
• /
• 2011

In this study, we organized the test results obtained from the performance tests for the CA certificated air cleaners which had been commercially available in Korea since 2003, and analyzed the correlation among the test parameters such as flow rate, particle collection efficiency, clean air delivery rate (CADR), ozone emission, odor removal efficiency and noise level etc. The noise level of 267 air cleaners were increased as concentrated at the 45, 50, 55 dB, which are the required noise level for CA certification according to flow rate, and ozone emissions from the CA air cleaners were significantly lower than the requirement limit, 50 ppb for 24 hour operation. The average particle collection efficiency and odor removal efficiency were 89.3 and 80.8%, approximately 20% higher than the requirement of CA certification, regardless of flow rates. The particle removal performance of an air cleaner was clearly discriminated by its CADR, and the CADR was obtained with a simple calculation: 0.79 x flow rate. The low differentiation of gas removal performance of air cleaners by the current CA gas test method was improved by 3.2, 751.3, 13.4 times for ammonia, acetic acid, respectively, by adopting the CADR concept and the real time measurement method, FTIR, for gas removal performance test.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2015

The objective of this study is to develop a high-performance foamed concrete made with a new mixture proportioning as an alternative of autoclaved lightweight concrete (ALC) block. For the early-strength gain of the foamed concrete under an atmospheric curing condition, the binders and chemical agents were specially contrived as follows: 3% anhydrous gypsum was added to ordinary portland cement (OPC) in which $3CaO{\cdot}SiO_2$ content was controlled to be above 60%; and the content of polyethylene glycol alkylether in a polycarboxylate-based water-reducing agent was modified to be 28%. Using these binders and chemical agents, 11 mixes were prepared with the parameters of W/B ratio (30% to 20% in a interval of 2.5%) and unit binder content ($400kg/m^3$ to $650kg/m^3$ in a interval of $50kg/m^3$). The quality and availability of the mixed foamed concrete were examined according to the minimum requirements specified in the KS for ALC block and existed conventional foamed concrete. The measured properties satisfied the minimum requirement of KS for ALC block and proved that the developed high-performance foamed concrete had considerable potential for practical application.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.138-144
• /
• 2004

Satellite generates a complex electromagnetic noise by conducted and radiated coupling effect of the various electrical instruments. This noise may cause serious problems on the satellite system. To minimize the electromagnetic coupling effects and maintain the system safety margin, system noise reduction technique should be applied from the beginning of the system design. The KOMPSAT-2 system is evaluated by measuring the conducted noise on system electrical power leads and verifying a 6dB system safety margin under the complex noise environment with current injection. This paper describes the KOMPSAT-2 system evaluation result performed on ETB(Electrical Test Bed) and the analysed noise element, the analysed result will be reflected on FM(Flight Model) EMC test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.7
• /
• pp.657-667
• /
• 2015

With development of technology and increase of commercial demand for unmanned aerial system(UAS), the related regulation has been prepared and complemented with the advanced countries such as Unite States and European Union(EU). However it is difficult for regulation to cover all areas of UASs practically since UASs have been developed in a variety of configurations and performance depending on their purpose. Therefore the reasonable criteria for the classification of UASs and their category should be suggested before development of the regulation. For this reason, many countries have been studying the standard for UASs classification and International Civil Aviation Organization(ICAO) makes an effort to prepare the international standards. In this paper, the new classification scheme which can complement domestic regulation is suggested based on investigation of the global trend of UAS classification and their researches.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.1
• /
• pp.129-136
• /
• 2012

This study seeks to evaluate the welding characteristics of SHN400 steel, which is suitable for the steel material used in building structures in KS. For this purpose, the Y-groove weld crack test and hardness, tensile, bending, cross tensile, and charpy V notch tests at the welding point were conducted with specimens taken from the highest, the thickest and the commonly used H-beams for girder or beam members. Each test was conducted under the KS test conditions. All tests results satisfied the requirements of KS and the welding requirements for the proper inelastic behavior of structure, indicating that SHN400 can be used for the building structure as a structural material.