• 기록학연구
• /
• 제15호
• /
• pp.307-311
• /
• 2007

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.7-8
• /
• 2006

본 논문은 Synthetic Bearing(Thordon bearing)을 적용하여 발생한 문제점을 분석, 대책 수립

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.258-258
• /
• 2017

• 대한조선학회논문집
• /
• 제42권5호
• /
• pp.479-486
• /
• 2005

The final goal of shift alignment design is that the bearing reaction forces or mean pressures are within design boundaries for various service conditions of a ship. However, it is found that calculated bearing load can be substantially variable according to the locations of the effective support points of after sterntube bearing which are determined by simple calculation or assumption suggested by classification societies. A new analysis method for shaft alignment calculation is introduced in order to resolve these problems. Key concept of the new method is featured by adopting both nonlinear elastic and multi-support elements to simulate a bearing support Hertz contact theory is basically applied for nonlinear elastic stiffness calculation instead of the projected area method suggested by most of classification societies. Three loading conditions according to the bearing offset and the hydrodynamic moment and twelve models according to the locations of the effective support points of sterntube bearings are prepared to carry out quantitative verifications for an actual shafting system of 8000 TEU class container vessel. It is found that there is relatively large difference between assumed and calculated effective support points.

• 대한조선학회논문집
• /
• 제53권6호
• /
• pp.447-455
• /
• 2016

Precise propulsion shafting alignment of ships is very important to prevent damage of its support bearings due to excessive reaction forces caused by hull deflection, forces acted on propeller and crankshaft, and so forth. In this paper, a new iterative shafting alignment calculation procedure considering the interaction between shaft deflection and oil film pressure of Sterntube Journal Bearing (SJB) bush with single or multiple slopes is proposed. The procedure is based on a pressure analysis to evaluate distributed equivalent support stiffness of SJB by solving Reynolds equation and a deflection analysis of shafting system by a finite element method based on Timoshenko beam theory. SJB is approximated with multi-point biaxial elastic supports equally distributed to its length. Their initial stiffness values are estimated from dynamic reaction force calculated by assuming SJB as single rigid support. Then, the shaft deflection and the support stiffness of SJB are sequentially and iteratively calculated by applying a criteria on deflection variation between sequential calculation results. To demonstrate validity and applicability of the proposed procedure for optimal slope design of SJB, numerical analysis results for a shafting system are described.

• 대한조선학회논문집
• /
• 제58권2호
• /
• pp.97-104
• /
• 2021

Together with the emerging of the Eco-ship, the application of large-diameter and high-efficiency propeller required more careful attention than before in the design of the shafting system. After the adoption of Environmentally Acceptable Lubricants (EAL) to the stern tube lubrication oil, a number of aft stern tube bearing accidents have been reported, and a variety of institutions have actively conducted research on the cause relationship. This study attempted to find the cause of the accident by measuring the alignment of the shafting system of a medium-sized product/chemical tanker with aft stern tube bearing damage and analyzing the reaction force of each bearing. In addition, a reasonable solution to the correction of the shaft alignment was suggested and the feasibility was reviewed. Through various measured data and analysis, the actual installation of shafting system was slightly different from the design drawing condition, but it was found that each bearing load distribution was within the allowable range. Therefore, it was confirmed that the cause of this accident was due to the dissatisfaction the misalignment slope of aft stern tube bearing rather than the effect of the bearing overload. As a solution to this cause, countermeasures such as double slope were suggested in the aft stern tube bearing, and the characteristics of EAL also seem to have an indirect effect.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권3호
• /
• pp.185-190
• /
• 2016

선박이 고출력화, 초대형화 됨에 따라 대형저속 2행정 엔진을 탑재한 선박에서 축계배치의 잘못에 기인하는 주기관 선미측 베어링과, 선미관 후부 베어링의 손상이 증가하는 경향이 있다. 또한 고출력화에 의한 추진축의 강성은 증가한 반면에 선체는 고장력 후판을 사용하므로 이전의 선체보다 훨씬 더 쉽게 변형하는 실정이다. 이는 기존의 선박보다 더욱 정교한 축계배치가 요구됨을 의미한다. 본 연구에서는 열팽창 효과, 감도지수를 이용한 중간축 베어링의 최적위치 선정 및 베어링의 강성을 고려하여, 베어링의 하중 분석 및 영향 계수를 분석함으로서 축계 배치가 이론적으로 최적이 되는 것을 검토하였다. 이를 위하여 축계 배치 계산시 대형 엔진 제조사의 엔진 거치기준을 참조하고, 한국선급 및 DnV 선급의 축계 배치 프로그램을 이용하여 검토하고 그 신뢰성을 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권5호
• /
• pp.47-54
• /
• 1991

The lip seals widely used nowadays in stern tube sealing system of ships have radial sealing contact with shafts or liners, on the other hand the face seals of stern tube sealing system have axial sealing contact with seat. Because of axial sealing contact, the face seals have a large number of merits such as durability of life, simplicity of structure, easy fitting and replacement, etc. In this paper, for the purpose of development of face seals, the fundamental properties of axial sealing contact were analyzed and a trial face seal was designed and manufactured using N.B.R. rubber and Thordon which is widely used for bearing materials. The seal proper of trial face seal was made from N.B.R. rubber and the face insert was made from Thordon, thermosetting resins which are three dimensional, cross linked condensation polylmers. The performance test of trial face seal was carried out on the test bench which was specially designed and manufactured. The results were satisfactory enough to be used in practical stern tube sealing system.

• 수산해양기술연구
• /
• 제35권1호
• /
• pp.50-53
• /
• 1999

In this paper, the mechanical movement of lip seal-ring which plays the most important function in stern-tube sealing system and the possibility of leakage caused by pressure fluctuation are studied by theory and experiment. By the finite element method for axial symmetry object which receives the torsional bending load, the displacement and stress analysis of the seal-rings are executed for products of several representative manufacturers of seal-rings, and also the possibility of crack occurance are checked by theoretical analysis. A sample seal-ring id designed and manufactured using the program of displacement and stress analysis developed in this study and made an experimental apparatus to test the sampling seal-ring. The sampling seal-ring functioned excellently, but it had its durability and this problem may be solved by using the Viton instead of NBR.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.3-4
• /
• 2005

With an increase in the size and power rate of ship, the stern tube bearing has become subject to severer operation conditions. Particularly it is expected to be exposed to extremely so severe lubrication conditions during low rotational operation that there is strong demand for clarifying the oil film characteristics of the stern tube bearing at the design stage with accuracy. So in this study, we conducted an analysis of the stern tube bearing characteristics taking arbitrary three-dimensional deflection of the shaft into consideration.