DOI QR코드

DOI QR Code

A case study on the optimal shafting alignment concerning bearing stiffness for 10,100 TEU container carrier

베어링 강성을 고려한 10,100 TEU 컨테이너 운반선의 최적 추진축계 배치에 관한 사례 연구

  • Received : 2015.09.21
  • Accepted : 2016.01.24
  • Published : 2016.03.31

Abstract

Damages of the main engine aftmost bearing and the after stern tube bearing tend to increase due to misalignment. And as the shafting system becomes stiffer due to the large engine power, whereas the hull structure becomes more flexible due to optimization by using high tensile thin steel plates. And this is the reason that more sophisticated shaft alignments are required. In this study, the optimum shafting alignment calculation was carried out, considering the thermal expansion effect, exploiting the sensitivity index, which indicates the reasonable position of forward intermediate shaft bearing for shaft alignment. and as the main subject in this study, the elastic deformation on intermediate shaft and main engine bearings occurred by vertical load of shaft mass were examined thoroughly and analyzed allowable load of bearings, reaction influence numbers of all bearings. As the result, a reliable optimum shafting alignment was derived theoretically. To verify these results, they were referred to the engine maker's technical information of main engine installation and being used shafting alignment programs of both Korean Register of Shipping and Det Norske Veritas, their reliability were reviewed.

선박이 고출력화, 초대형화 됨에 따라 대형저속 2행정 엔진을 탑재한 선박에서 축계배치의 잘못에 기인하는 주기관 선미측 베어링과, 선미관 후부 베어링의 손상이 증가하는 경향이 있다. 또한 고출력화에 의한 추진축의 강성은 증가한 반면에 선체는 고장력 후판을 사용하므로 이전의 선체보다 훨씬 더 쉽게 변형하는 실정이다. 이는 기존의 선박보다 더욱 정교한 축계배치가 요구됨을 의미한다. 본 연구에서는 열팽창 효과, 감도지수를 이용한 중간축 베어링의 최적위치 선정 및 베어링의 강성을 고려하여, 베어링의 하중 분석 및 영향 계수를 분석함으로서 축계 배치가 이론적으로 최적이 되는 것을 검토하였다. 이를 위하여 축계 배치 계산시 대형 엔진 제조사의 엔진 거치기준을 참조하고, 한국선급 및 DnV 선급의 축계 배치 프로그램을 이용하여 검토하고 그 신뢰성을 검증하였다.

Keywords

References

  1. R. Michel, "A quarter century of propulsion shafting design practice and operating experience in the U.S. Navy," Naval Engineers Journal, p. 153, 1959.
  2. H. C. Anderson and J. J. Zrodowski, "Co-ordinated alignment of line shaft, propulsion gear, and turbines," Society of Naval Architects and Marine Engineers, vol. 67, pp. 449-523, 1959.
  3. W. E. Lehr, "Considerations in the design of marine propulsion shaft system," Society of Naval Architects and Marine Engineers, vol. 67, p. 555, 1961.
  4. G. Mann, "Shipyard alignment of propulsion shafting using fair curve alignment theory," Naval Engineers Journal, vol. 77, no. 4, pp. 651-659, 1965. https://doi.org/10.1111/j.1559-3584.1965.tb04996.x
  5. Y. J. Lee, A Study on Hull Deflections Effecting the Ship's Propulsion Shafting Alignment, Ph.D. Dissertation, Department of Mechanical Engineering Graduate School, Korea Maritime University, Korea, 2006 (in Korean).
  6. American Bureau of Shipping, Guidance Notes on Propulsion Shafting Alignment, Houston, USA : American Bureau of Shipping, 2006.
  7. K. C. Kim and J. G. Kim, "A study on optimum shaft alignment analysis for VLCC," Proceedings of the Special Transactions of the Society of Naval Architects of Korea, pp. 134-137, 2005 (in Korean).
  8. Class NK, GUIDELINES ON SHAFTING ALIGNMENT, Japan, Class NK, 2006.
  9. H. J. Jeon, Ship Propulsion Transmission Equipment, Busna, Korea, Taehwa Publishing Company, 1986 (in Korean).
  10. C. O. Seo, A Study on the Optimal Shafting Alignment for Chemical Tanker of Medium Size, M.S thesis, Department of Marine System Engineering Graduate School, Korea Maritime and Ocean University, Korea, 2010 (in Korean).
  11. Korean Register of Shipping, SeaTrust-SHALI Shaft Alingment Program User Manual, Korea, 2009 (in Korean).

Cited by

  1. 173,000 CBM 액화천연가스 운반선의 선체변형을 고려한 추진축계 정렬해석 연구 vol.42, pp.4, 2016, https://doi.org/10.5916/jkosme.2018.42.4.258