• Journal of the Korean Geotechnical Society
• /
• v.34 no.11
• /
• pp.107-119
• /
• 2018

PHC piles, extension-plate attached PHC piles, and steel pipe attached PHC piles were installed in field test site. Axial compressive static load tests including load distribution test and Pile Driving Analyzer (after driving) were done on the tip-transformed PHC piles and the grouted tip-transformed PHC piles. Load-displacement curves of three different type of PHC piles, which are PHC pile (TP-1), extension plate attached PHC pile (TP-2) and steel pipe attached PHC pile (TP-3), showed almost the same behavior. Thus bearing capacity increase effect of the tip-transformed PHC piles was negligible. Share ratio of side resistance and end bearing resistance for PHC pile, extension plate attached PHC pile, and steel pipe attached PHC pile were 95.8% vs. 4.2%, 95.6% vs. 4.4%, and 97.8% vs. 2.2% respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1207-1214
• /
• 2014

Under excessive plasticity, the fracture toughness of a material depends on its size and geometry. Under fully yielded conditions, the stresses in a material near its crack tip are not unique but rather depend on the geometry. Therefore, the single-parameter J-approach is limited to a high-constraint crack geometry. The JQ theory has been proposed for establishing the crack geometry constraints. This approach assumes that the crack-tip fields have two degrees of freedom. In this study, the crack-tip stress field of a fully circumferential surface-cracked pipe under combined loads is investigated on the basis of the JQ theory by using finite element analysis. The combined loads are a tensile axial force and the thermal gradient in the radial direction. Q-stresses of the crack geometry and its loading state are used to determine the constraint effects. The constraint effects of secondary loading are found to be greater than those of primary loading. Therefore, thermal shock is believed to be the most severe loading condition of constraint effects.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1063-1070
• /
• 1988

The influence of the inlet pressure on bearing performance of tilting pad bearings in laminar regime is examined. A simple flow model is presented to calculate the inlet pressure in inlet flow that occurs at a short distance ahead of the bearing inlet. The bearing performances are obtained, load capacity, friction torque and lubricated flow-rate, etc, numerically for the inlet pressure boundary conditions with and without pressure jump. The computed results of both cases show that bearing performance and the optimum pivot position changes remarkably according to the bearing operating conditions. The influence of the inlet pressure on bearing performance must be considered to analyze the bearing performance precisely.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.2
• /
• pp.161-169
• /
• 1999

이방성체의 평면내 직선균열에 대한 균열선단부근의 응력과 변위의 분포는 어떠한 균열체의 형상 및 하중조건에 대해서도 응력확대계수라는 하나의 매개변수로서 나타낼 수 있다고 하는 것이 파괴역학에서 보편화되어 있다. 그러나 많은 경우에 있어서 급수전개식의 이어지는 항은 정량적으로 중요하다. 따라서 본 연구에서는 이러한 항을 유도하고 이것이 균열진전방향에 미치는 영향에 대하여 검초하였다. 이를 위하여 단축하중을 받는 직방성균열체의 해석을 수행하며 재료는 균질이방성체라고 가정하였다. 급수전개식에서 2차항의 영향을 고려하기 위하여 균열선단에서의 응력의 분포를 재해석하였으며, 2차항의 사용은 정확한 균열진전방향의 결정을 위해서 매우 중요함을 보였다. 초기균열진전각도의 결정을 위해서 수직응력비이론을 적용하였다.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.61-70
• /
• 2008

Load settlement behaviors and load transfer characteristics of rock-socketed pile subjected bi-directional load at pile tip were investigated using bi-directional pile load tests (BD PLT) performed on ten large-diameter drilled shafts at four sites. Based on test results, additional pile-toe displacement ($w_{bs}$) by coupled soil resistance was analyzed, and thus equivalent top loaded load-settlement curve of pile subjected bi-directional load was proposed by taking into account the coupled soil resistance. Through comparisons with field case studies, it is found that for test piles there exists effect of coupled soil resistance, which is represented by wbs, and thus an equivalent curve obtained by existing uncoupled methods can overestimate bearing capacity of piles by BD PLT. On the other hand, the analysis by the proposed method with soil coupling effect has a considerably larger settlement when compared with the results by uncoupled load transfer method and estimates reasonable load-settlement behaviors of test piles. In case of pile socketed in high strength rocks, however, effects of coupled soil resistance can be neglected.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.3
• /
• pp.29-34
• /
• 2013

In this paper, numerical analyses were conducted on piled raft foundation settlement and pile bearing characteristics in soft ground. Results obviously showed longer and larger piles developed end bearing capacity values, but also showed the load of the central pile is larger than the surrounding piles in a group formation. Additionally, after pile yielding, the load carrying capacity exists as a raft. Moreover, results showed no transverse displacement according to embedment depth for the single pile case, but larger transverse displacements for deeper embedment depths.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.226-226
• /
• 2003

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.526-532
• /
• 2009

말뚝의 정재하시험을 통하여 항복하중 및 극한하중을 판별하는 다양한 방법이 제안되어 왔다. 말뚝의 지지력은 주면마찰력과 선단지지력의 합으로 나타내어 왔으나 말뚝 재하시험을 통한 항복 하중 및 극한하중의 판별법은 대체로 총 침하량에 대해 판별하거나 재하하중-침하 그래프로부터 산정되는 경우가 대표적이다. 본 연구에서는 현장 대구경 양방향 재하시험 결과를 활용하여 말뚝의 주면부와 선단부로 나누어 항복하중을 판별할 수 있는 방법을 제안하고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.6
• /
• pp.5-13
• /
• 2000

모래지반의 상대밀도, 말뚝의 시공방법, 일정근입깊이에 따른 소요향타 에너지 그리고 지하수 조건에 따라 말뚝의 지지력과 하중전이를 연구하기 위하여 강관말뚝을 이용한 모형실험을 수행하였다. 매입말뚝은 말뚝을 미리 설치한후에 지반성형을 실시하였고, 타입말뚝은 매입말뚝과 같은 깊이까지 항타높이를 5, 10, 15cm로 달리하여 말뚝을 관입하였다. 그 뒤 정적하중을 단계적으로 가하여 하중-침하 곡선에 의한 모형 말뚝의 지지력과ㅏ 말뚝내의 등간격으로 설치된 변형 게이지를 이용하여 타입말뚝 의 하중전이에 대해 살펴보았다. 타입말뚝의 하중전이시험에서는 항타 전과 항타 후 말뚝내 하중전의 소효항타 에너지에 따른 변화를 관찰하였다. 매입말뚝의 시험결과는 현재 가장 많이 사용하고 있는 대표적인 정적 지지력 공식들에 의하여 계산되어진 값들과 비교 분석하였다. 그 결과 상대밀도가 작은 느슨한모래지반에서는 Vesic 공식이 그리고 상대밀도가 큰 조밀한 모래지반에서는 Hanbu 공식이 가장 근접한 평가를 나타내었다. 하중전이시험에 의한 항타시 잔류응력은 모든 경우에서 지표면과 선단부위에서 아주 큰 잔류응력이 나타났고. 말뚝의 선단 지지력비는 상대밀도에 비례하게 증가하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.943-951
• /
• 2014

The tip geometries of the pyramidal and conical indenters used for micro/nano-indentation tests are not sharp. They are inevitably rounded because of their manufacturability and wear. In many indentation studies, the tip geometries of the pyramidal indenters are simply assumed to be spherical, and the theoretical solution for spherical indentation is simply applied to the geometry at a shallow indentation depth. This assumption, however, has two problems. First, the accuracy of the theoretical solution depends on the material properties and indenter shape. Second, the actual shapes of pyramidal indenter tips are not perfectly spherical. Hence, we consider the effects of these two problems on indentation tests via finite element analysis. We first show the relationship between the Poisson's ratio and load-displacement curve for spherical indentation, and suggest improved solutions. Then, using a possible geometry for a Berkovich indenter tip, we analyze the characteristics of the load-displacement curve with respect to the indentation depth.