• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.12
• /
• pp.1280-1286
• /
• 2006

Three different virgin activated carbons made of each coal(Calgon), coconut(Samchully) and wood(Picabiol) based activated carbon(AC) were tested for an adsorption performance of 1,4-dioxane in a continuous adsorption column. Breakthrough behavior was Investigated that the breakthrough points of coal, coconut and wood based AC were observed as 3600 bed volumn(BV), 1440 BV and 144 BV respectively. Adsorption capacity(X/M) of coal, coconut and wood based AC was observed. The reported results of adsorption capacity showed that coal based AC was highest(578.9 ${\mu}g/g$), coconut based AC was intermediate(142.3 ${\mu}g/g$) and wood based AC was lowest(7.4 ${\mu}g/g$) due to increasing specific surface area. Moreover, carbon usage rates(CURs) for coal, coconut and wood based AC had been shown as 0.48 g/day, 1.41 g/day and 6.9 g/day respectively. The constant characteristic of the system, k of coal based AC was found to be 91.5 and k of coconut based AC was found to be 17.9. Removal efficiencies of 1,4-dioxane with different ozonation dosages(2 and 5 mg/L) for 20 min ozonation had been shown 38% and 87% respectively. There was no observation for biological removal of 1.4-dioxane by attached micro-organisms when used(3.1 years and over 5 years) biological activated carbon(BAC) without pretreatment of oxidation were employed. When a combination of ozonation(2 mg/L and 5 mg/L) and BAC process for $10{\sim}30$ min was applied, removal efficiency for 1,4-dioxine increased only $2{\sim}6%$ compared to only applying ozonation. Therefore removal efficiency of BAC process prior to using oxidation was proven to negligible. Consequently, the results presented in this paper provide a better insight into the adsorption performance of 1,4-dioxane. This observation suggests that using virgin activated carbon made of coal is the best selection for removal of 1,4-dioxane in the water treatment for an advanced treatment. It is clear from this research that longer EBCT for ozonation or higher ozone concentration are more effective operation methods for removal of 1,4-dioxane than longer EBCT in the BAC process.

• Korean Journal of Ecology and Environment
• /
• v.40 no.2
• /
• pp.318-326
• /
• 2007

Characteristics of organophoshhorus pesticides (OPs) distribution were investigated in Shingu Reservoir, as a shallow eutrophic agriculture reservoir in Korea. In August 2006, IBP, DDVP and dyfonate were detected in the water column of Singu Reservoir, ranging from 1340.7 to 16030.1 ng $L^{-1}$, 58.7 to 127.6 ng $L^{-1}$ and N.D. to 20.3 ng $L^{-1}$, respectively, However, in September 2006, mevinfos, ethoprofos, phorate, chlorfenvinfos, and methidathion were also found in addition to IBP (202.5${\sim}$213.2 ng $L^{-1}$), DDVP (100.7${\sim}$340.6 ng $L^{-1}$) and dyfonate (N.D.${\sim}$25.0 ng $L^{-1})$. Maximum concentrations of OPs were observed at the middle depth in August, which might be related with photo-oxidation. On the other hand, IBP and DDVP among the OPs were detected in suspended particles, suggesting the relatively active adsorption reactivity. The composition of OPs varied temporally on account of the influence of inflow water from its surrounding areas. In the present study, the observed OPs concentrations seem to be not acute toBic levels to aquatic organisms in Shingu Reservoir, considering the standard monitoring levels of U.S. Environmental Protection Agency and Japan Ministry of Environment.

• Journal of Korea Water Resources Association
• /
• v.36 no.6
• /
• pp.1013-1023
• /
• 2003

This study was performed to improve water quality of stream by applying hydraulic structures (weir and river bed material) made of porous concrete. The physical and chemical characteristics of porous concrete were measured to estimate application possibility of it in hydraulic structures and it was considered as a proper material for the hydraulic structures. In the results of comparison for the component of matters attached on the hydraulic structures made of porous and ordinary concrete, DW (dry weight) amount attached on porous concrete was 1.6 times higher than that on ordinary concrete under the condition of the same flow rate but influence by flow rate (difference of 10 times) was not shown. Therefore, we could understand that the material of media was more important in DW amount than flow rate. The rate of AFDM (ash free dry mass) to DW also was more at porous concrete than at ordinary concrete. Especially, the high rates of nitrogen and phosphorous in matters attached on porous concrete verify that they were removed by assimilation, adsorption and metabolism of periphyton. The removal percentage of SS, BOD, COD, T-N and T-P by hydraulic structures applying porous concrete compared with ordinary concrete was increased by 34.6%, 36.9%, 33.9%, 18.3% and 21.6%, respectively. Therefore, applying porous concrete to hydraulic structure is expected to contribute to improvement of stream water quality.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.83-83
• /
• 2017

생체재료의 표면은 이식과 동시에 생체계면의 역할을 하게 되어, 일련의 생물학적 반응이 시작되고 진행되는 중요한 장소가 된다. 초기에 생체계면에서 일어나는 단백질 흡착이나 염증반응을 비롯한 생물학적 반응들은 궁극적으로 임플란트의 성패를 좌우할 만큼 중요하다. 골융합을 개선하기 위한 다른 방법으로 생체불활성의 타이타늄 (Ti)과 골조직의 능동적인 반응을 이루기 위해 생체활성 표면을 부여함으로서 계면에서의 골형성 반응을 증진시키는 방법이 이용된다. 생체불활성의 Ti과 Ti합금은 골조직과 직접적인 결합을 이루지 못하므로, 골조직과의 반응을 향상하기 위해 여러 종류의 생체활성 재료를 코팅하는 방법이 연구되어 왔고, 이 중 생체의 변화와 가장 유사한 하이드록시아파타이트 코팅이 가장 대중적인 방법으로 사용되었으며 이는 초기 골형성을 촉진하는 것으로 알려졌다. 치과용 임플란트의 표면형상과 화학조성이 골 융합에 영향을 미치는 가장 중요한 인자이므로 최근의 연구동향은 이들 두 가지 표면특성을 결합함으로서 결과적으로 최적의 골세포반응을 유도하고, 골융합 후 골조직과의 micromechanical interlocking에 의해 임플란트의 안정성에 중요한 역할을 하는 마이크론 단위의 표면조도와 표면 구조를 유지하면서, 부가적으로 골 조직 반응을 능동적으로 개선할 수 있는 생체활성 성분을 부여하여 골 융합에 상승효과를 이루기 위한 표면처리법에 관해 많은 연구가 요구되어지고 있다. 따라서 골을 구하는 원소인 망간과 실리콘으로 치환된 하이드록시아파타이트를 플라즈마 전해 산화법으로 코팅하여 세포와 잘 결합할 수 있는 표면을 제공함으로써 골 융합과 치유기간을 단축시킬 수 있을 것으로 사료된다. 실험방법은 시편은 치과 임플란트 제작 합금인 Ti-6Al-4V ELI disk (grade 5, Timet Co., USA; diameter, 10 mm, thickness, 3 mm)이며, calcium acetate monohydrate, calcium glycerophosphate, manganese(II) acetate tetrahydrate, sodium metasilicate을 설계조건에 따라 혼합 제조된 전해질 용액을 이용하여 플라즈마 전해 산화법으로 표면 코팅을 실시하였다. 각 시편의 플라즈마 전해시 전압은 280V로 인가하였고, 전류밀도는 70mA로 정전류를 공급하여 해당 인가전압 도달 후 3분 동안 정전압 방식을 유지하였다. 코팅된 피막 표면을 주사전자현미경과 X-선 회절분석을 통하여 미세구조 및 결정상을 관찰하였다. 또한 코팅된 표면의 생체활성 평가는 정량적으로 평가하기 위해 동전위시험과 AC 임피던스를 통하여 시행하였다. 분극거동을 확인하기 위해 potentiostat (Model PARSTAT 2273, EG&G, USA)을 이용하여 구강 내 환경과 유사한 $36.5{\pm}1^{\circ}C$의 0.9 wt.% NaCl에서 실시하였다. 전기화학적 부식 거동은 potentiodynamic 방법으로 조사하였고 인가전위는 -1500 mV에서 2000 mV까지 분당 1.67 mV/min 의 주사속도로 인가하여 시험을 수행하였다. 임피던스 측정은 potentiostat (Model PARSTAT 2273, EG&G, USA)을 이용하였으며, 측정에 사용한 주파수 영역은 10mHz ~ 100kHz 까지의 범위로 하여 조사하였고 ZSimWin(Princeton applied Research, USA) 소프트웨어를 사용하여 용액의 저항, 분극 저항 값을 산출하였다. 망간의 함량이 증가할수록 불규칙한 기공을 보였으며, 실리콘은 $TiO_2$ 산화막 형성을 저해하는 경향을 확인할 수 있었다. 단독으로 표면을 처리한 경우보다 두 가지 원소를 이용해 복합 표면처리를 시행한 경우가 내식성이 좋아 임플란트과의 골 유착에 긍정적인 영향을 미칠 것으로 사료된다.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.8
• /
• pp.822-828
• /
• 2005

The photocatalytic degradation of methyl parathion was carried out using a circulating $TiO_2$/solar system. Under the photocatalytic condition, parathion was more effectively degraded than by the photolysis or $TiO_2$ only condition. The parathion degradation followed pseudo first-order kinetics. With photocatalysis, 10 mg/L parathion was completely degraded within 90 min with a TOC decrease exceeding 63% after 150 min. The nitrogen from parathion was recovered mainly as ${NO_2}^-$, ${NO_3}^-$, and ${NH_4}^+$, 80% of sulfur as ${SO_4}^{2-}$, and less than 5% of phosphorus as ${PO_4}^{3-}$ during photocatalysis. The organic intermediates 4-nitrophenol and paraoxon were also identified, and these were further degraded. Two different bioassays using V. fischeri and D. magna were employed to measure the toxicity reduction in the solutions treated by both photocatalysis and photolysis. Relative toxicity was reduced almost completely after 150 min in both organisms under the photocatalysis, whereas in photolysis, 76 and 57% reduction was achieved for V. fischeri and D. magna, respectively. The acute toxicity reduction pattern corresponded with the decrease in parathion and TOC concentrations.

• The Korean Journal of Pesticide Science
• /
• v.3 no.1
• /
• pp.57-65
• /
• 1999

The midge Chironomus riparius is a member of widespread dipteran insect which has been used for sediment toxicity test. The 2nd-3rd larvae Chironomus riparius were exposed to $^{14}C$-lambda-cyhalothrin in laboratory water only system(A) and sediment-water system(B) at $20{\pm}2^{\circ}C$. The concentration was nominally in the range of 0.16 to $20{\mu}g/{\ell}$ and 62.5 to 8000 ${\mu}g/kg$, respectively. System(A) was prepared by applying the chemical to 250 ml water and introducing Chironomus riparius larvae into the system(day 0). System(B) was prepared by applying the chemical to the 25 g of soil and 250 ml water and shaking and rolling them for two hours. After allowing the system to settle for two days, Chironomus riparius larvae were introduced into the system. After 72 hours, the two systems were terminated and dead larvae were observed. The measurement of residue in water was conducted at the start(day 0) and the end of the study(day 3). The residue of $^{14}C$-lambda-cyhalothrin in water was accounted for approximately 65% of nominal concentration in system(A) and $0.2{\sim}0.4%$ in system) on 3 days. $LC_{50}$ was less than $0.156{\mu}g/{\ell}$ in system(A) and 889 ${\mu}g/kg$ in system(B), based on the nominally applied concentration.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1997.04a
• /
• pp.114-114
• /
• 1997

항만개발 사업은 매립이나 준설과 같은 해안선과 해저지형을 변화시키는 공사가 이루어지며 이는 조석조류 현상의 변화를 유발하게 된다. 특히 해안지형이 복잡한 항만이나 하구에서는 변화정도가 크게 나타나며 방파제나 선박접안 시설과 같은 항내 구조물을 축조 할 경우에도 조석조류 변화가 야기된다. 조석조류 현상의 변화는 해양 수질과 생물상에 영 향을 줄뿐만 아니라 인접한 육지에 이르기까지 크다란 피해를 유발할 수가 있다. 창조시 해 수를 육지로 범람하게 하거나 퇴적이나 침식조건을 변화시킬 수도 있으며 오염물질이 외해 로 확산되는 과정을 방해하고 해양생물의 서식조건을 악화시켜 부근 해역의 어업에 피해를 유발할 수도 있다. 또한 해안 공사 과정에 해수로 유입되는 토사나 항만 이용시에 배출되는 폐수 등이 항내 수질과 생태계를 변화시킬 수 있다. 따라서 조석조류와 수질변화를 사전에 예측하고 이를 최소화하는 방안이 강구되어야 한다. 조석조류와 수질 변화를 사전에 예측하 는 방법으로 축소모형 실험과 컴퓨터 시뮬레이션이 사용된다. 축소모형 실험은 현장을 재현 하는데 많은 경비와 시간이 소모되며 예측에 한계가 있다. 반면에 컴퓨터 시뮬레이션은 대 상해역의 지형과 조류 그리고 수질특성에 적합하게 모델을 개발할 경우 예측력이 매우 높기 때문에 현재 가장 널리 이용되고 있다. 본 연구는 유한 요소법에 기초하여 미국 공병단 (United States Army Corps of Engineers)에서 개발한 TABS-2 모델을 이용하여 온산항에 서 시행되는 부두건설에 따른 조석조류 및 수질변화를 시뮬레이션하였다. 측정된 자료로 모 델 계수를 보정하고 검증하였으며 항내 매립과 준설이 이루어질 때 나타나는 조위와 조속변 화를 예측하였다. 매립과 준설공사시 유출되는 토사가 조석조류현상에 따라 이동 확산되는 범위와 농도분포를 예측하였다.ophobic components)은 75~80%, 친수성 물질(hydrophilic components)은 30~33%정도의 분포를 보였고, 전염소 및 전오존 공정을 거친 처리수에서는 각각 62.2-62.8%, 43.9~49.0% 및 50~ 55%, 40~57% 정도의 분포를 보였다. 그리고 웅집-침전을 거친 처리수에서는 그 분포가 77~82%, 24-48%였다. 전주리 공정을 통하여 소수성 물질(byoghobic components)의 분포가 감 소하는 것을 볼 때 전염소 및 전오존 처리가 용존유기물의 응집에는 오히려 역 효과를 나타내는 것으로 판단된다. 것으로 판단된다.여 황토 2g에 대하여 Hieltijes and Lijklema 방법에 의해 Adsorbed-p, Nonapatite inorganic-P(NAI-P), Apatite-p, Organic-P로 구분하여 분석하고, 총인(Total Phosphorus)을 Standard Methods에 따라 Persulfate digestion후 0.45 m membrane 여지 여과하여 여액에 대해 PO3-4-P의 농도를 Ascorbic Acid 법으로 측정한 결과, NAI-P가 가장 큰 비율을 차지하였고, 부원료로 첨가된 금속 양이온 중 Fe3-이온이 흡착에 기여하는 정도가 가장 큰 것으로 평가되었다.다당류 T-AS의 보체 활성화 기작은 classical과 alternative complement pathway의 양 경로를 통해 활성화 되었다. T-AS 분획은 mouse내의 특정 혈청단백을 증가시켰으며, 항체 생성능의 증가가 관찰되어 effect T 세포의 활성화가 나타나고 있음을 알 수 있었다. T-AS는 생체내 투여시에 대식세포의 탐식능이 증진되었으며, 대식세포 기능 저해제에 의한 대식세포의 기능 저해 현상이 회복되었다. 이와 같은 결과들로부터, T-AS의 항암 활성은 활성

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.317-321
• /
• 2012

This study was carried out to investigate the effect of EC levels in nutrient solution on the growth of rose in coir substrate during the juvenile. Nutrient concentration were EC 0.6, 1.0, 1.4, and $1.8dS{\cdot}m^{-1}$. In spite of high concentration of nutrient solution was supplied, EC and inorganic ions content in the extract of substrate was no difference by 22 days after planting. After that, they was rapidly increased with higher concentration of nutrient solution. Number of shoot was highest in EC $1.8dS{\cdot}m^{-1}$ at 2nd growth cycle, 90 days after planting, after that was showed a tendency to increase with increasing nutrient concentration, but was no significant difference among treatment except EC $0.6dS{\cdot}m^{-1}$. Judging by results of growth of rose and contents of inorganic ion in extracts of media, our experiment suggests that the suitable nutrient concentration is EC $1.8dS{\cdot}m^{-1}$ until 90 days and then EC $1.4dS{\cdot}m^{-1}$ until 165 days after planting that is more higher than conventional nutrient concentration for absorption by coir.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.991-1000
• /
• 2000

Methanotrophic consortium utilizing methane as the primary carbon source and secreting soluble methane monooxygenase (sMMO) was immobilized on celite R-635 to continuously treat a wastewater containing trichloroethylene (TCE). With influent 2 ppm of TCE. 80.4 and 84.5% of TCE was degraded in 6 and 20 hour of hydraulic retention time (HRT). respectively. and the removal efficiency of TCE was increased with an increase in HRT in methanotrophic consortium biofilm reactor (MCBR). With influent 5 ppm of TCE and 10 hour of HRT. average efficiency of TCE removal was decreased in initial stage. but gradually increased to 81%. TCE was degraded to 88.5 and 96.5% with 10 and 15 hour of HRT. respectively. when methane was supplied alternately with continuous oxygen supply at influent 5 ppm of TCE. The efficiency of TCE degradation was decreased probably because oxidation reaction of methane was proceeded slowly on MMO. when high concentration of methane was supplied with depletion of oxygen. As results of the pilot-scale study. biodegradation of TCE by MCBR system might be feasible at full-scale operation.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.6
• /
• pp.323-328
• /
• 2016

Pressurized membrane used for side-stream MBR process requires fouling control strategy both for normal and abnormal operation conditions for stable operation of the facilities. In this study, $85m^3/day$ of pilot-scale side-stream MBR process was constructed for the evaluation of fouling mitigation by air bubble injection into the membrane module. In addition, fouling phenomena at abnormal operation conditions of low influent and/or loading rate were also investigated. Injection of air bubble was found to be effective in delaying transmembrane pressure (TMP) increase mainly due to scouring effect on the membrane surface, resulting in expanded filtration cycle at a high flux of $40L/m^2{\cdot}h$ (LMH). At abnormal operation condition, injection of PACl (53 mg/L as Al) into the bioreactor showed 19% reduction of TMP increase. However, inhibition of nitrifying bacteria by continuous PACl injection was observed from batch experiments. In contrast, injection of powdered activated carbon (PAC, 0.6 g/L) was able to maintain the initial TMP of $0.2kg/cm^2$ for 5 days at the abnormal conditions. It may have been caused from the adsorption of extracellular polymeric substances (EPS), which was known to be excessively released during growth inhibition condition and act as the major foulants in MBR operations.