• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.255-257
• /
• 2018

본 논문은 리튬폴리머 배터리를 입력 전압원으로 High-Altitude Electomagnetic Pulse (HEMP) 구동용 고밀도 고전압 충전기의 설계를 다루며, 제안하는 충전기는 독특한 3상 델타-와이 변압기 구조를 갖는 5.4kW 용량의 LCC 공진 컨버터로 제작 되었다. 풀브릿지 형태로 4개의 스위치를 사용하는 단상 충전기는 동일 용량을 설계하는 경우, 입력 전류량이 높아 소자의 발열로 충전기의 동작 시간이 제한되고 누설 인덕턴스에 의한 스파이크성 전압이 크게 발생하여 충전기의 안정적인 구동이 어려운 문제점이 있다. 이를 해결하기 위해 6개의 스위치를 사용하는 삼상 충전기를 HEMP 구동용 고밀도 고전압 충전기에 적용하였다. 동일 용량의 단상과 삼상 충전기 설계과정과 시뮬레이션 결과를 분석해 각 충전기의 차이점을 비교하고, 저항 및 커패시터 부하 실험으로 제안하는 삼상 충전기의 동작과 성능을 검증하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.400-408
• /
• 2007

In this paper, development of the 8kW parallel module converter is presented. For a effective configuration of FB-PWM converter, this paper proposes 4-parallel operation of 2 kw-module. FB converter of 2-kW module is controlled by phase shut PWM and in order to achieve ZVZCS, the simple auxiliary circuit is applied in secondary side. In order to achieve ZCS, control logic for auxiliary circuit operation is designed to reset the primary current during free-wheeling period. For output current sharing of 4-modules, the charge control is employed. The charge control logic is designed with phase shift PWM logic. Voltage controller is implemented by using DSP(TMS320LF2406) with A/D conversion data of the output current and voltage of each module. The developed converter is installed in PCU(Power Conditioning Unit) for HSG(High Speed Generator) in a vehicle and health monitoring system is implemented for vehicle operation test. Finally, performance of the developed converter is proved under practical operation of HSG.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.985-991
• /
• 2018

In this paper, an equivalent circuit reflecting the internal loss of the LLC resonant half bridge converter was proposed and a steady state characteristic equation including the loss factors was derived. Using the results, the frequency characteristics of I/O voltage gain and input impedance were compared with the lossless model In order to verify the proposed model and the derived equation, the main components of the 1kW class LLC resonant half bridge converter were selected under the same conditions and the steady state characteristics such as voltage gain and input impedance were compared. In particular, to compare more closely the steady state error of the two models, we observed the change in switching frequency with respect to the load current, which is considered to be the most important in the actual circuit design stage. As a result, it is confirmed that the error of the operating frequency is significantly improved from the proposed model and the analysis result.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.2
• /
• pp.259-266
• /
• 2021

USB bus not only works with convenience but also transmits data fast and becomes a standard peripheral interface between FPGA development board and personal computer. In this paper FPGA verification system with slave FIFO interface for Cypress FX3 USB 3 bridge chip was implemented. The designed slave FIFO interface consists of host interface module based on FIFO structure, master bus controller and command decoder and supports streaming communication interface for FX3 bridge chip and memory-mapped input and output interface for user design circuit. The ZestSC3 board with Cypress FX3 USB 3 bridge chip and Xilinx Artix FPGA(XC7A35T-1C5G3241) was used to implement FPGA verification system. It was verified that the FPGA verification system for user design circuit operated correctly under various clock frequencies using GUI software developed by visual C# and C++ DLL. The designed slave FIFO interface for FPGA verification system has modular structure and can be applicable to the different user designs with memory-mapped I/O interface.

• The KIPS Transactions:PartC
• /
• v.10C no.2
• /
• pp.185-190
• /
• 2003

Bluetooth communication is based on piconet, which is composed by one master and maximum seven slaves. Several piconets can be interconnected via an inter-piconet Bluetooth unit called a bridge unit to form a Bluetooth scatternet. This bridge node can make its presence in each piconet by switching. This switching must be carefully scheduled so that slot wastage and, hence, packet delays are minimized. In this paper, we introduce an efficient inter-piconet scheduling scheme based on sniff mode. This scheme tries to minimize the wastage of slots by having the bridge unit sniff with its peering masters with time limits and communicate with its slaves in remaining slots. The sniff time limits are determined adaptively based on the amount of traffic in each piconet. Simulation results show this scheme outperforms round-robin scheme based on sniff intervals of equal lengths.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.419-426
• /
• 2002

A new active lossless snubber for half-bridge dual converter(that is called'dual converter') is proposed in this paper It features soft switching(ZVS) as well as turn-off snubbing in both main and auxiliary switches. Therefore, it helps the dual converter to operate at the higher frequency with a higher efficiency and smaller-sized reactive components. Moreover, since it uses parasitic components, such as leakage inductances and switch output capacitances etc, to achieve the ZVS of power switches, it has simpler structure and lower cost of production. The operational principle, theoretical analysis, and design consideration are presented. To confirm the operation, features, and validity of the proposed circuit, experimental results from a 200w, 24V/DC-200V/DC proto-type are presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.5
• /
• pp.396-402
• /
• 2008

This paper presents the structure and performance of a new Integrated magnetics-based transformer, which can be readily adapted to zero-voltage switching full bridge dc-to-dc converters. The proposed transformer features with two paralleled primary windings and a center-tapped secondary winding. The transformer can be fabricated on standard EE or EI cores where the primary and secondary windings are placed on the outer legs while the output filter inductor is wound on the middle leg. The performance of the proposed transformer is demonstrated with a 100 kHz 720 W experimental dc-to-dc converter which recorded a 92% conversion efficiency at 12 V output voltage.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.2
• /
• pp.105-113
• /
• 2011

In this paper, photovoltaic module integrated converter (MIC) based on active clamp current-fed half-bridge converter is proposed. The converter stage operates in zero-voltage condition using active clamp technique. The theoretical study and circuit design for proposed inverter are confirmed with PSIM simulator and experimental reusult.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.561-569
• /
• 1999

In this paper, the diode bridge-type ZVT(Zero- Voltage Transition) inverter is proposed. It consists of one a auxiliaI${\gamma}$ switch, three resonant inductors and six blockin당 diodes. So, the main advantage of the proposed t torXJ!ogy is the reduction of the auxiliar${\gamma}$ switch compare to the conventional ZVT inverter. The topology of t the propostxl lVT inverter is analyztxl with a description of the control conditions based on the load current. A And the resonant period control for operating the proposed inverter optimally is discussed by using resonant i inductor current ftxxlback. To verify the proposed topology, the detailed simulation and exJX끼mental results i indicate that zero volta당e operation during transition can be achieved.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1043-1045
• /
• 2002

고전압 전원공급기를 고 밀도로 제작하기 위하여 고 주파수 동작을 시켜야 한다. 이에 따라 전원 공급기에서 최대의 부피를 차지하는 부품인 변압기는 원하는 주파수에서 최소의 부피로 충분한 전력을 수용하면서 완벽한 펄스재현을 하여야 한다. 고전압 전원공급기는 풀-브릿지 DC/DC 컨버트로 구성되어 있으며 스윗칭 주파수는 100 kHz 이다. 변압기는 일차권선이 1개이며 이차 권선은 4개로 구성된다 일차전압은 250 Vdc, 이차 권선 각각의 출력은 520 Vrms이다. 변압의 이차 권선은 배 전압 회로를 이용하여 승압 후 각각을 직렬로 연결하여 -4,100 VDC와 -2,050 VDC를 만들어 TWT(Travel Wave Tube)의 케소드 및 콜렉트에 공급한다. 이 변압기는 100 kHz 펄스로 동작하고 최대부피가 400$cm^3$이하가 되어야 한다. 본 논문에서는 이러한 변압기의 설계 방법 및 최소 온도상승을 위한 적절한 동작 자속밀도의 선택에 대하여 기술하고 변압기의 누설 인덕턴스, 분포 케페시턴스, 공진 주파수에 대하여 설계치 및 실험치를 비교 평가하였다.