• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.17 no.1
• /
• pp.35-40
• /
• 1981

This pape presents a study of stability of the two mass rotor with limited power similar to that employed by Kononenko and also presents a study on the digital computer to obtain the unstable region of the ;'ot::r oyer two critical speed ranges. The unstable region is identified by studying the Routh-Hurwitz criterion of the chc.rc.cteristic equation. The results are presented in two and three-dimensional diagrams to show how the various parameters affeCt the unstable region.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.486-491
• /
• 1998

본 연구에서는 충돌면의 형상에 따른 고속 원형 충돌제트의 불안정 모드를 밝히기 위하여 우선 충돌면의 형상에 따른 주파수 특성을 비교하고자 하였다. 이를 위해 충돌면이 제트의 직경보다 작은 원판(small plate)과 제트의 직경보다 큰 구멍(hole)의 2가지 경우에 대하여 실험을 하였고, 평판 충돌음에 대한 연구결과와 비교 검토하였다.

• 열병합발전
• /
• s.78
• /
• pp.4-9
• /
• 2010

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1393-1398
• /
• 2000

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1210-1217
• /
• 1999

This paper presents schematic process of identifying the principal cause to make the vibration problem of rotating circular saws. In the tandem pencil slat saw lines, feeding of cedar blocks is often stopped because excessive motro current is required in a saw motor. These events are called "kick-offs" in technical reports. Research on saw behavior at kick-offs is required to understand are reduce the frequency and severity of kick-offs events. This research aims at finding out the principal cause of kick-offs, and evloving design improvements for high cutting performance with fewer and less severe kick-offs. Measurements of critical speed, cutting force, cutting temeprature and dynamic displacements are carried out to observe the instability mechanism and also to obtain saw design parameters for the numerical analyses. And the numerical analyses involving FEM and multiple scale method are utilized to show the possibility of the principal cause.pal cause.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.809-813
• /
• 2010

For the purpose of developing a modeling technique for reduced-order dynamics of thermoacoustic instability, we constructed an electrically heated Rijke tube and measured the pressure oscillation inside the tube. Analysing the measured pressure data showed that the instability generated three major oscillation modes, among which the first mode frequency quite well matches the result from a rough acoustic analysis. As a continuing research, a data-based modeling technique for the thermoacoustic instability will be developed in the near future.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.114-115
• /
• 2010

• Journal of the KSME
• /
• v.27 no.6
• /
• pp.478-488
• /
• 1987

회전기계의 고성능, 고속화에 따라 베어링 유막특성에서 자려진동이 발생하기 쉬운 조건이 되고 더욱이 고압화에 의해 자동유체로부터 불안정한 힘이 증대하게 되었다. 또한, 고속화에 의해 계의 운전속도가 1차 위험속도 이상으로 되어 시동, 정지시에 위험속도를 통과하여야 하며, 고차 위험속도에서의 공진가능성 등을 충분히 검토하여야 한다. 따라서 종래의 실제방법만으로는 회전기계의 진동문제에 충분히 대처할 수 없는 상태이다.

• Journal of the KSME
• /
• v.56 no.9
• /
• pp.54-57
• /
• 2016

로켓연소기는 수백 개의 분사기로 구성된 연소실에서 연소반응이 발생하게 된다. 이때 구조적인 특성으로 난류유동, 밀도, 온도 등의 변화가 매우 불균일한 3차원적인 분포를 가지게 된다. 이러한 불균일한 분포에 의해 발생되는 압력의 시간변화가 연소기의 고유진동수와 일치될 경우 공진이 발생하게 되어 폭발이 발생하게 된다. 이러한 현상을 연소불안정이라 하고 이글에서는 관련된 연구의 동향을 소개하고자 한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1066-1071
• /
• 2007

This case study refers to turbine-generator with retrofitted turbine rotor. Vibration problem occurring after the retrofit was mainly due to high vibration from exciter side. However, repeated test run and operation during scheduled maintenance caused high vibration from generator bearing, and post-overhaul test run before turbine vibration correction caused oil whip on the bearing. This case study shows how to analyze vibration condition of high turbine generator vibration detected during the post-overhaul test run and vibration condition of offline and online data to reflect it on establishing maintenance schedule and overhaul correction procedure. Vibration data could be acquired during steady load operation or even with varying speed and load. Each data is important for machinery condition evaluation. This case study shows that the vibration data during extreme condition is the key factor in analysis, which helps to find the machinery problem.