• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.157-164
• /
• 1997

일반적으로 콘크리트와 철근간의 경계면을 나타내는 유한요소법에는 균열의 부근에서 발생하는 부착열화 현상을 고려하지 않고 있다. 이것은 균열 부근에서 과도한 부착을 초래하고 , 국소 변형과 균열의 진전에도 영향을 준다. 본 연구에서는 철근콘크리트 구조물의 균열부근에서 일어나는 부착거동의 변화를 고려한 비선형 부착응력-미끄럼 모델을 제안하였다. 철근과 콘크리트간의 경계면에는 링크요소를 이용하였고, 링크의 특성은 철근을 가로지르는 균열의 상태에 따라 변하도록 조정하였다. 균열의 형성상태를 정량화하고, 부착거동을 두 포락선 1) 균열로부터 충분히 떨어진 위치에서의 부착상태를 모델링한 외연포락선, 2)횡균열면에 있어서의 부착상태를 모델링한 내연포락선의 사이에 변이시키기 위하여 비국소적 손상도 개념을 도입하였다. 이 방법의 유효성을 알아보기 위하여 편재하중을 받는 T형 교각의 실험 및 해석결과를 제시하였다. 제안된 모델의 결과를 실험결과와 비교하여 본 모델의 유용성을 검증하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.10
• /
• pp.855-864
• /
• 2009

The effect of toxicant on the inhibition of nitrification was investigated, using concentrated nitrifying bacteria of both attached and suspended growth. This nitrifying organism was originally obtained from the activated sludge of sewage treatment plant and cultivated for more than three months. The object of this experiment is to determine the effect of the specific surface area and the growth condition of nitrifying bacteria on toxicity of heavy metal. The results of this study were as follows. The specific surface area of both attached and suspended growth of nitrifying organism was proven to be a major factors in determining the inhibition of nitrification of heavy metal such as $Cu^{++}$ion. When the condition of attachment and detachment was compared in an experiment using attached growth nitrifier, the effect on toxicant was 1.12 times less in attached condition than in detached condition for Nitrosomonas, and 1.09 times less for Nitrobacter. In case of suspended growth nitrifier, the effect on toxicant was 1.46 times less in non-ground condition than in ground condition for Nitrosomonas, and 1.35 times less for Nitrobacter. Also, similar results were obtained in a set of experiments, without adding nitrite to the substrate. In an experiment that compared attached condition using attached growth nitrifier with detached condition using attached growth nitrifier, the effect on toxicant was 1.83 times less in attached condition than in detached one for Nitrosomonas, and 1.78 times less for Nitrobacter. In case of suspended growth nitrifier, the effect on toxicant was 1.27 times less in non-ground condition than in ground condition for Nitrosomonas, and 1.32 times less for Nitrobacter.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.3
• /
• pp.247-255
• /
• 2010

Bonding strength of shotcrete is a significant influential factor which plays the role of collapse prevention of tunnel crown and of debonding prevention of shotcrete induced by the blasting vibration. Thus, the evaluation of the shotcrete bonding state is one of the core components for shotcrete quality control. In this study, the peak particle velocities induced by blasting were measured on the shotcrete in a tunnel construction site and its effect on the bonding state of shotcrete is investigated. Drilling and blasting technique was used for the excavation of intersection tunnel connecting the main tunnel with the service tunnel. Blast-induced vibrations were monitored at some points of the main tunnel and the service tunnel. The shotcrete bonding state was evaluated by using impact-echo test coupled with the time-frequency domain analysis which is called short-time Fourier transformation. Analysis results of blast-induced vibrations and the time-frequency domain impact-echo signals showed that the blasting condition applied to the excavation of intersection tunnel hardly affects on the tunnel shotcrete bonding state. The general blasting practice in Korea was evaluated to have a minor negative impact on shotcrete quality.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.507-515
• /
• 2001

Significant improvements in bond strength between new and existing concrete can be achieved through the modification of the new concrete by latex. This study focuses on the investigation of bond strength of latex modified concrete. Pull-out bond test and uniaxial direct tensile bond test are adopted for evaluating the adhesion characteristics of latex modified concrete to conventional concrete substrate. The main experimental variables are test methods, latex-cement ratio, surface preparations and moisture levels. The results are as follows; The increase of latex-cement ratio substantially improves the adhesion between latex modified concrete and substrate. The effects of surface preparation at substrate into the bonding of latex modified concrete are quite different according to the conditions of surfaces. Thus, an adequate surface preparations are essential for good bond strength. Because the moisture level of the substrate may be critical to achieving bond, optimum moisture condition for a conventional concrete has evaluated in this study. The saturated condition of surface is the most appropriate moisture level among the considered, followed by dry condition and wet condition.

• Journal of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.547-554
• /
• 2013

This study was intended to estimate the bond strength of steel fiber in UHPFRC through pullout test. The pullout test was carried out with the double-sided pullout specimens with multiple fibers. First, the effect of fiber density on the bond strength was investigated, and the experimental result presented that the density range considered in this study was proved not to produce fiber-to-fiber interaction. The bond strength was estimated from several methods, which are based on the pullout load or energy at peak load, and the total energy absorbed until fibers are pulled out completely. the estimated bond strength obtained from the total energy was shown to be under the influence of the embedded length of fiber. the bond strengths obtained from peak load condition was 6.64 MPa in average, which had little difference compared to 6.46 MPa calculated by peak load only. Considering simplicity of test and analysis, it may be no matter to estimate the bond strength from peak load in pullout test.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.3
• /
• pp.149-160
• /
• 2015

This study reports the interfacial bond strength between Ultra High Performance Concrete (UHPC) and Normal Strength Concrete (NSC). While previous studies have focused on the interfacial strength between NSC substrate and UHPC overlay, this study use precast UHPC for enhanced constructability and replacement of formwork. The factors affecting the interface strength are comprehensively reviewed. It can be classified into: interface shape, degree of hardening and moisture condition of UHPC before combining with NSC, and curing condition of composite materials. Conducted experiments verify the effects of each factor on the interface strength and, accordingly show different failure modes. In particular, a new failure mode of the failure of a part of UHPC was firstly found in the case of sample with rough interface between UHPC and NSC. The other factors of the degree of hardening and the moisture and curing conditions of UHPC were discussed. This research will provide a valuable foundation to utilize the UHPC as a composite material.

• International Journal of Highway Engineering
• /
• v.3 no.4 s.10
• /
• pp.117-126
• /
• 2001

In this research, evaluation of adhesion in tension property of SBR-modified concrete to ordinary portland cement concrete was conducted with uniaxial direct tensile bond test which was proposed by Kuhlmann. A test set-up was fabricated in order to minimize the eccentric force by introducing a joint which might fully rotate. The main experimental variables were cement-latex ratios, surface preparations and moisture levels. The results obtained were as follows: The LMC specimen at 15% latex-cement ratio increased the adhesion in tension by range of 37% compared to that of conventional cement concrete. This might be due to latex film formed between cement paste and aggregate. The effects of surface preparation on bond of latex modified concrete to conventional concrete were significant at the conditions by sand paper and wire brush. A better bond could be achieved by rough surface rather than smooth. The saturated and surface dry (SSD) condition were considered to be the most appropriate moisture level followed by wet, finally by dry. Thus, a proper surface preparation and moisture level are quite necessity in order to obtain better bonding at LMC overlay.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.189-190
• /
• 2016

본 논문은 휠체어의 탑승자의 구동력과 BLDCM(Brushless DC Motor) 에서 출력되는 보조력인 전기적인 구동력을 동시에 사용하는 탈부착형 수전동 휠체어의 제어기를 제안한다. 제안된 방식에서는 탈부착형 수전동 휠체어 제어기는 휠체어의 기울기와 휠체어의 상관관계를 바탕으로, 탑승자의 휠체어 림 구동 상태를 추정하여 휠체어의 전동력을 전달하는 BLDCM에서 구동력을 사용자의 지령에 따라 보조하도록 제어한다. 사용자의 요구 상태는 림의 구동에 따른 휠체어의 상태를 가속도, 자이로 센서를 이용해 측정을 하게 되고, 이를 상보필터를 사용해 각도를 보정하여, 지령치를 계산하고, 구동부는 지령치에 따라 휠체어에 필요한 전동력을 발생하게 된다. 탈부착형 수전동 휠체어의 제어방식은 시뮬레이션을 통해 가능성을 검증하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.68-74
• /
• 2014

Recently, concrete facility as advanced water treatment facilities is extending in the water treatment facilities according to raise awareness of pure drinking water and delicious water. For this reason, it is increased to the necessity need to make the standard and the development of waterproofing and anti-corrosion materials for concrete structures applied water treatment tank. So, related research has become active recently. However, as the limit of research focused on durability improvement of top coating material, it is insufficient to study on the adhesion strength between the concrete surface and primer. Therefore, there is to confirm the adhesion of between concrete surface and the three primers used as anti-corrosion waterproofing materials, and to investigate the properties of adhesion strength according to the condition such as dry condition, wet condition, and water pressure condition of the concrete surface in this study.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.12
• /
• pp.1611-1617
• /
• 2018

The body temperature of livestock is directly related to the health of livestock such that it changes immediately when there exists health problem. Accordingly, the monitoring of livestock's temperature is one of most important tasks in farm management. However, the temperature of livestock is usually measured using skin-attached sensor which is significantly affected by the outside temperature and the condition of attachment which results in the inaccurate measurement of temperature. Herein we have proposed new scheme which estimates the body core temperature of cow based on measured data from neck-attached smart sensor. Especially, we have considered both schemes which estimate the exact temperature and which detect the unusually high temperature based on machine learning. We have found that the occurrence of high temperature can be detected accurately. The proposed scheme can be used in monitoring of health condition of cow and improving the efficiency of farm management.