• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.256-257
• /
• 2005

To estimate a electrical performance of the extra high voltage XLPE cable the discharge properties due to shift of void position were investigated. The $\Phi-q-n$ properties have been measured at room temperature by rising voltage ratio of 0.5[kV]. An obtained data was stored to personal computer through A/D converter. The period of applied wave form and discharge values were divided into 64 parts and discharge values generated during 10 seconds were accumulated by phases. As a result, it was confirmed that the charge, phase angle and counts of discharge changed due to void position.

• The Journal of the Korea Contents Association
• /
• v.22 no.3
• /
• pp.567-575
• /
• 2022

This study was carried out to elucidate bioacive effects of three domestic cherry tomato cultivars. Total polyphenol and flavonoid of Summerking, Qutiquti, and Minichal cultivar were 12.56±1.88, 12.50±1.92, 11.65±1.85 mg/g and 4.58±1.03, 4.19±0.40, 4.30±0.49 mg/g(dry weight) respectively. Domestic cherry tomatoes showed antioxidative activity(DPPH and ABTS radical scavenging activities). All of the cherry tomatoes had no cytotoxicity for normal liver cell, but showed strong inhibitory effect against cervical cancer cell(HeLa) growth. These results revealed that domestic cherry tomatoes can be used as a bioactive food material.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1081-1084
• /
• 1995

Internal voids located within an insulation will arise partial discharge that causes local breakdown and even the entire insulation breakdown. For HV apparatuses, it is usual case that several voids are formed within non-uniform electric field condition rather than single void within uniform field, which can be solved analitically. The purpose of this work is to study partial discharge and breakdown characteristics of an insulation according to the distribution pattern of two disc-type voids that are located within non-uniform field. The results from numerical field analysis and experiments show that the electric field within the voids decreases as they are arranged more serially, which accordingly results in the increase of partial discharge inception field(PDIF) much higher than that of single void model. With parallel arranged voids, PDIF is almost the same as that of single void model. On the other hand, AC breakdown strength decreases as voids are arranged more serially, which is a natural result considering the reduction of effective insulation thickness. For parallel voids, this effect cannot he noticed where as they show different pattern compared with single void and serial void models in $\Phi$-Q-N analysis. Considering these results may leads us to the conclusion that, in the evaluation of insulating products through PD test, it is not sufficient to determine only PDIV or existence of PD at predetermined voltage level. We could evaluate more accurately by considering all the available data such as PDIV, PD magnitude, PD occurring phase, number of PD pulses, and etc.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.1
• /
• pp.9-18
• /
• 2007

This study shows an implementation of partial holes in an initial design domain in order to improve convergences of topology optimization algorithms. The method is associated with a bubble method as introduced by Eschenauer et al. to overcome slow convergence of boundary-based shape optimization methods. However, contrary to the bubble method, initial holes are only implemented for initializations of optimization algorithm in this approach, and there is no need to consider a characteristic function which defines hole's deposition during every optimization procedure. In addition, solid and void regions within the initial design domain are not fixed but merged or split during optimization Procedures. Since this phenomenon activates finite changes of design parameters without numerically calculating movements and positions of holes, convergences of topology optimization algorithm can be improved. In the present study, material topology optimization designs of Michell-type beam utilizing the initial design domain with initial holes of varied sizes and shapes is carried out by using SIMP like a density distribution method. Numerical examples demonstrate the efficiency and simplicity of the present method.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.11-17
• /
• 2010

The electromigration phenomenon in lead-free flip-chip solder joint has been one of the serious problems. To understand the mechanism of this phenomenon, the crystallographic orientation of Sn grain in the Sn-Ag-Cu solder bump has been analyzed. Different time to failure and different microstructural changes were observed in the all test vehicle and bumps, respectively. Fast failure and serious dissolution of Cu electrode was observed when the c-axis of Sn grain parallel to electron flow. On the contrary of this, slight microstructural changes were observed when the c-axis of Sn perpendicular to electron flow. In addition, underfill could enhance the electromigration reliability to prevent the deformation of solder bump during EM test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.5
• /
• pp.12-23
• /
• 1994

The two-phase flow is observed in power plants, chemical process plants, and refrigeration systems etc., and it is very important to solve the heat transfer mechanism of a boiler, an automic reactor, a condenser and various types of evaporators. Recently, the problem of two phase heat transfer is braught up in many regions with development of energy saving technique. In flow boiling system it is necessary to store data in each condition because the heat transfer characteristics of flow boiling region vary by the change of flow pattern and the magnetude of heat flux to tube length, and be subtly affected by the flow and heating condition. So basic study for knowing flow pattern in heat transfer region and the relation between heat transfer characteristic and flow condition is desired to accumulate data in wide variety of liquid and flow system in the study of heat transfer of two phase flow. In this study R-113 was selected as working fluid whose properties were programmed by least square method, and experiment was conducted in the region of mass flow $1.628{\times}10^6$~$4.884{\times}10^6$/kg/$m^2$hr with inlet subcooling 10~3$0^{\circ}C$, sustaining test section inlet pressure to 1.5kg$_f$/$cm^2$abs.

• Fire Science and Engineering
• /
• v.16 no.1
• /
• pp.39-44
• /
• 2002

In this paper, we analysed the flame patterns and the electrical characteristics of the electric outlet which was fired at standby mode. The carbonized patterns indicated that the flame had spread about 50 cm to 70 cm. After the combustibles on wall started to burn, the temperature went up to about $300^{\circ}c$ in 150 sec. The flame formed ceiling jet and spread quickly. The tracking was generated at the shortest distance between two electrodes and the resistance was about 100$\Omega$ to 300$\Omega$ As the result of analysis using metallurgical microscope, the normal part of a blade holder showed amorphous structure, but the melted part of a blade holder damaged by tracking showed dendrite structure and void evenly. When the blade holder of damaged outlet was analyzed by SEM and EDX, we found that the structure and components of the normal part were different from those of melted part.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.27-30
• /
• 2001

Electromigration Phenomena in Al-1%Si thin film interconnections under DC and PDC conditions were investigated. Thin film interconnections with $SiO_2$ and PSG/$SiO_2$ dielectric passivation layer were formed by a standard photolithography process method and test line lengths were 100, 400, 800, 1200, and 1600 $\mu\textrm{m}$. The current density of $1.19\times10^7\textrm{A/cm}^2$ was stressed in Al-1%Si thin film interconnections under DC condition. The current density of $1.19\times10^7\textrm{A/cm}^2$ was also applied under PDC condition at the frequency of 1 Hz with the duty factor of 0.5. The electromigration resistance of PSG/SiO2 dielectric passivation test line was stronger than $SiO_2$ dielectric passivation test line. The lifetime under PDC was 2-4 times longer than DC condition. As the thin film interconnection line increased, the lifetime decreased and saturated over the critical length. Failure patterns by an electromigration were dominated by void-induced electrical open and hillock-induced electrical short.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.3
• /
• pp.241-247
• /
• 2014

This study presents the ultrasonic nonlinearity of AISI316 austenitic stainless steels subjected to longterm isothermal aging. These steels are attractive materials for use in industrial mechanical structures because of their strength at high-temperatures and their chemical stability. The test materials were subjected to accelerated heat-treatment in an electrical furnace for a predetermined aging duration. The variations in the ultrasonic nonlinearity and microstructural damage were carefully evaluated through observation of the microstructure. The ultrasonic nonlinearity stiffly dropped after aging for up to 1000 h and, then, monotonously decreased. The polygonal shape of the initial grain structures changed to circular, especially as the annealing twins in the grains dissolved and disappeared. The delta ferrite on the grain boundaries could not be observed at 1000 h of aging, and these continuously transformed into their sigma phases. Consequently, in the intial aging period, the rapid decrease in the ultrasonic nonlinearity was caused by voids, dislocations, and twin annihilation. The continuous monotonic decrease in the ultrasonic nonlinearity after the first drop resulted from the generation of $Cr_{23}C_6$ precipitates and ${\sigma}$ phases.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.1014-1016
• /
• 2010

우리나라 쌀 생산량은 해마다 증가되고 있으나, 1인당 쌀 소비량은 급격히 감소되고 있는 수급 불균형을 이루고 있다. 특히 충청남도는 최근 6년간 전국 쌀 생산량 1위를 차지해 오고 있어서 쌀 소비의 확대방안이 더욱 절실히 요구되고 있는 지역적 특성을 지니고 있다. 취반용 쌀 소비량 확대만으로는 쌀 소비량 증대에 한계점이 있으므로, 소비자의 요구에 맞는 고 기능성, 간편식으로 다양한 기호성을 지닌 쌀 가공식품 형태의 개발이 필요하게 되었다. 이러한 요구에 적합한 제품개발로 쌀을 이용한 쌀국수를 개발하고자 하였으며, 이러한 쌀국수 제품개발은 쌀을 이용한 제품개발은 또다른 시도가 되어 쌀 소비촉진이 향상될 것으로 기대된다. 기능성 쌀국수 개발을 위하여 천연물 중 연잎 소재를 첨가하였다. 연잎은 차와 사찰음식을 대표하는 소재중 하나이다. 연잎에는 비타민 C와 섬유소가 매우 풍부하다. 이러한 성분은 미용식품으로써의 응용이 가능하며, 식이 섬유소는 배변작용에도 도움이 될 수 있다. 또한 항산화제인 quercetin이 다량 함유되어 있다. 이 quercetin은 플라보이드 배당체이며, 우리 몸의 세포의 노화를 유발하는 유해 활성 산소를 제거하는 기능을 가지고 있다. 따라서 이러한 유해 활성산소를 억제하는 것이 항산화 활성이 높은 연잎을 이용하여 고 기능성 쌀가공품 제품 개발이 가능할 것으로 기대한다. 쌀가루 50%를 기준으로하여 연잎가루는 3% 첨가하였으며, 전분의 종류를 달리하여 최종 제품을 개발한 결과, texture analyser로 물성을 측정한 결과 타피오카 전분과 쌀가루 혼한 쌀국수의 물성이 좋은 결과를 나타내었다. 관능검사 결과도 타피오카 전분과 쌀가루 혼합 쌀국수가 소비자들의 기호도가 높은 선호도를 나타내었고, 감자전분과 밀가루는 다소 낮은 선호도를 나타내었다. 본 연구를 기초로 하여 쌀제품 개발시 쌀의 가공적성 및 기능성 소재의 첨가 비율 확립하고, 연잎과 같은 쌀국수에 첨가 가능한 다양한 기능성 소재 발굴 및 첨가 가능성을 제시하고자 하였다.