• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.11-16
• /
• 2003

The objective of this study is to clarify the seismic capacity and the characteristics in the hysteretic behavior of RC structures with non-seismic detailing. To do this, an exterior beam-column subassemblage was selected from a ten story RC building and six 1/3-scale specimens were manufactured with three variables; (1) with and without slab, (2) upward and downward direction of anchorage for the bottom bar in beams, and (3) with and without hoop bars in the joint region. The test results have shown that (1) the existence of slab increased the strength in positive and negative moment, 25% and 52%, respectively; (2) the Korean practice of anchorage (downward and 25 $d_{b}$ anchorage length) caused the 8% reduction of strength and the early strength degradation in comparison with the case of seismic details; and (3) the existence of hoop bars in the joint region shows significant role in preventing the pull-out.t.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5844-5853
• /
• 2014

This paper presents the results of experimental investigations on the shear failure behaviors of reinforced concrete beams using ductile fiber reinforced cementitious composite (DFRCC). Total 10 RC beams of $150{\times}300{\times}1,000mm$ size were tested by 4-point bending under the displacement control. The main parameters of the experiment are surface treatment by grinding and preloading to the cracking point in the repair process. The load-displacement curves, diagonal tension cracking load, flexural cracking load, and shear strength were obtained. The test results showed that the DFRCC can be used effectively for restoring the shear strength approximately 99% to the original value under the condition that the appropriate thickness and surface treatment like grinding are assured. For further research, the specimens taken from real deteriorated structures will need to be tested after being repaired with DFRCC.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.17-20
• /
• 2008

This study presents experimental results of Steel-PSC hybrid beams having a rear plate joint with a perfobond rib shear connector between the steel girder and the prestressed concrete girder. Three specimens of 3.9m length(3.6m span length) were tested to evaluate the flexural characteristics of the joint under the condition of the three point loading. Based on load-deflection curves and failure modes of specimens by the experimental test, it is found that the proposed joint with the perfobond rib shear connector shows the higher strength and initial stiffness and the sufficient ductility. Therefore, the suggested perfobond rib shear connector can perform effectively as the joint of the Steel-PSC hybrid structural system.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.39-39
• /
• 2011

하천에서 수공구조물을 설계시 구조물의 규모, 형식, 운영방식, 안정성 등을 검토하기 위하여 일반적으로 수리모형실험과 수치모형실험을 이용한다. 수리모형실험은 자연현상의 왜곡을 최소화하여 검토결과를 얻을 수 있다는 장점이 있지만, 많은 시간과 비용, 인력 및 공간이 필요하기 때문에 단기간에 다양한 검토가 필요한 경우에는 많은 제약이 따른다. 반면에 수치모형실험은 제한적인 조건에서 검토목적 및 용도에 따라 다양한 수치모의기법을 활용하여 상대적으로 낮은 비용과 신속하고 다양한 검토가 가능하다는 장점을 가지고 있다. 그러나 수치모형실험은 어디까지나 자연현상에 대한 수학적, 물리적 기법을 활용한 분석이기 때문에 결과에 대한 신뢰성 확보가 매우 중요하다. 최근에는 컴퓨터의 계산능력 향상과 유체의 복잡한 동수역학적 거동 해석 기법의 다양화, 그리고 많은 적용성 검토 연구결과로 인한 신뢰성 향상 등으로 인해 수치모형실험에 대한 관심이 높아지고 있다. 본 연구는 현재 금강에 건설 중인 금강보에 대하여 다차원 수치모형인 EFDC(Environmental Fluid Dynamics Code)를 이용하여 하천 구조물 및 물리적 환경변화에 대한 정밀수리분석을 실시하기 위한 사전절차로, EFDC 모형을 하천수리해석에 적용할 경우 모형에 포함되어 있는 다양한 변수설정 및 제약조건들에 대하여 적용한계를 검토하고자 한다. 검토방법은 금강보가 건설되기 이전의 하천지형 상황에서 EFDC 모형과 HEC-RAS 모형을 이용한 수리분석을 수행하고, 수리거동 결과 들을 상호 비교 분석 한다. 수치모의 대상구간은 금강보 건설구간을 포함하여 약 20km 구간이고, 대상구간에 대하여 3차원 정밀지형자료를 구축하였으며, 과거 호우사상에 대한 구간 내 관측 수위 및 모형별 계산수위결과를 비교 검토하였다.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.441-450
• /
• 2010

This is a preliminary study on the development of precast beam-column joints for dry construction methodology. Precast beam column joints with thru-connectors (BCJ_TC) using high strength bars or PS strands were developed and their seismic performance including strength degradation, stiffness degradation and energy dissipation capacity was experimentally evaluated. Test results showed that compressive failures at the end blocks of PC beam members occurred dominantly while PC columns including panel zones were free from any damage. However, the connections confined with CFRP at the end block showed much improved seismic performance than that of the unconfined connections. Connections with neoprene pad fillers between beam and column interfaces were better than the other connections in all the seismic performances except initial stiffness. To improve the seismic performances of BCJ_TC, compressive strength of the concrete at the end block need to be increased to compensate for the additional compressive stresses due to unbonded connectors and deformation of connectors should be controlled respectively.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.6
• /
• pp.533-541
• /
• 2010

H-shaped beams, which are constructed between columns, are used widely as slaves in steel structures. The bending moments that occur on both ends of an H-shaped beam, however, are about twice the bending moment that occurs at the center of the H-shaped beam. Because such beam is designed with maximum bending moment, it is deeper and has smaller spaces. To improve these features, if both ends of an H-shaped beam that have maximum bending moments are merely reinforced, the beams could be designed by the bending moment at the center of the H-shaped beam. To analyze the structural performance of the proposed end-reinforced beams (eco-girders). Four specimens were prepared with the following parameters: end-reinforced steel plate, reinforced bars, and reinforced studs and experimental tests of the specimens were performed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5318-5326
• /
• 2014

This paper presents the results of flexural test of concrete beams reinforced with GFRP and conventional steel reinforcement for comparison. The beams were tested under a static load to examine the effects of the reinforcement ratio and compressive strength of concrete on cracking, deflection, ultimate capacity, and modes of failure. The test results showed that the ultimate capacity of the GFRP-reinforced beams increased with increasing reinforcement ratio and concrete strength, showing a 41.3~51.6% increase compared to steel reinforced beams. The deflections at maximum loads of the GFRP reinforced beams were 4.1~6.3 times higher that of steel reinforced beams. The measured deflections of GFRP reinforced beams decreased approximately 31% compared to the theoretical predictions because the theoretical flexural stiffness was underestimated at the maximum loads. For the GFRP-reinforced beams, the ACI code 440 design method resulted in conservative flexural strength estimates.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.119-126
• /
• 2006

This paper presents the results of a test program for flexural strengthening characteristics of continuous unidirectional carbon-fiber sheets bonded or/and developed to reinforced concrete (RC) beams. A total of six $150mm{\times}250mm{\times}2000mm$ concrete beams were tested. Various sheet development locations were studied to determine their effects on the ultimate flexural strength of the beams. From the test, it was found that the strength increases remarkably with the development of sheets at shear bar. Among the various location, multi-developed sheet provided the most effective strengthening for concrete beam. Beam strengthened using this scheme showed 53% increase in flexural capacity as compared to the control beam without any strengthening.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.328-331
• /
• 2011

준정적 횡하중을 재하 받는 철근콘크리트 보-기둥 접합부의 전단강도에 대한 주요 영향요인을 Bayesian parameter estimation의 신뢰성 이론 접목을 통해 검토하였다. 이와 같은 연구 scope의 수행을 위해 철근콘크리트 보-기둥의 실험 database가 구축되었다. 실험 database는 일정한 criteria을 적용하여 구축되었으며, 포함된 시편들은 최종적으로 접합부 내의 전단파괴가 지배하는 경우들이다. 포함된 시편들의 상세는 ACI (American Concrete Institute) 352R-02를 기준으로 평가되어졌다. 보-기둥 접합부의 전단강도에 영향 요인을 편중되지 않게 평가하고자, Bayesian parameter estimation의 신뢰성 이론을 적용하였다. Bayesian parameter estimation의 적용을 통해 전단강도에 영향이 적은 변수 (not informative parameter)를 순차적으로 제거 (stepwise removal process)함으로 주요 영향요인의 우선 순위를 확인할 수 있었다. 검토된 8개의 변수들 중에서, 횡하중을 재하 받는 철근콘크리트 보-기둥의 전단강도는 주로 콘크리트 압축강도, in-plane geometry, 종방향 보의 주철근 그리고 접합부 내의 구속철근 순으로 영향을 줌을 알 수 있었다.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.1
• /
• pp.16-23
• /
• 1997

As analysis of the forced dynamic response and vibrational mode for the cantilevered beam is described. Experimental results are compared with the natural frequencies and vibrational modes for the cantilevered beam using the theory of Bernoulli-Euler and finite element method. We have found 1st and 2nd resonance frequency of the cantilevered beam by means of the various external frequencies, $1{\sim}70Hz$, using magnetic transducer. And we have studied the vibrational displacement at obtained resonance frequency of the cantilevered beam. The experimental results for the nodes of cantilevered beam were 0 in 1st mode and 0,0.786 in 2nd mode. close agreement between the theoretically predicted results and experimental result was obtained for the vibrational mode.