• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.56-62
• /
• 1997

The PAN (Polyacrylonitrile) based carbon fiber-ceramic composites (CFCC) were prepared from mixtures of short carbon fibers, phenolic resin and ceramic binder. The effects of carbonization temperature of a pre-cursor fiber, the stabilized PAN fiber, on the specific surface area and the bending strength of the activated CFCC were studied in this work. The precursor fiber was carbonized at 80$0^{\circ}C$ and 100$0^{\circ}C$, respectively. The CFCC were activated at 85$0^{\circ}C$ in carbon dioxide for 10~90 minutes. As the burn-off of the activated CFCC made of the precursor fiber carbonized at 80$0^{\circ}C$ was increased from 37% to 76%, the specific surface area in-creased from 493m2/g to 1090m2/g, and the bending strength decreased from 4.5MPa to 1.4MPa. These values were about two times larger than those of the activated CFCC of which precursor fiber was car-bonized at 100$0^{\circ}C$. The effects of carbonization temperature of a precursor fiber on the specific surface area and bending strength of the activated CCFC were explained by bonding force between carbon fiber and car-bonized phenolic resin as well as by relative shirnkage between carbon fiber and ceramic film.

• Restorative Dentistry and Endodontics
• /
• v.35 no.2
• /
• pp.69-79
• /
• 2010

The purpose of this study was to evaluate the effect of film thickness of various resin cements on bonding efficiency in indirect composite restoration by measurement of microtensile bond strength, polymerization shrinkage, flexural strength and modulus, fractographic FE-SEM analysis. Experimental groups were divided according to film thickness (< $50\;{\mu}m$-control, $50\;{\mu}m$-T50, $100\;{\mu}m$-T100, $150\;{\mu}m$-T150) using composite- based resin cements (Variolink II, Duo-Link) and adhesive-based resin cements (Panavia F, Rely X Unicem). The data was analyzed using ANOVA and Duncan's multiple comparison test (p < 0.05). The results were as follows ; 1. Variolink II showed higher microtensile bond strength than that of adhesive-based resin cements in all film thickness (p < 0.05) but Duo-Link did not show significant difference except control group (p > 0.05). 2. Microtensile bond strength of composite-based resin cements were decreased significantly according to increasing film thickness (p < 0.05) but adhesive-based resin cements did not show significant difference among film thickness (p > 0.05). 3. Panavia F showed significantly lower polymerization shrinkage than other resin cements (p < 0.05). 4. Composite-based resin cements showed significantly higher flexural strength and modulus than adhesive-based resin cements (p < 0.05). 5. FE-SEM examination showed uniform adhesive layer and well developed resin tags in composite-based resin cements but unclear adhesive layer and poorly developed resin tags in adhesive-based resin cements. In debonded surface examination, composite-based resin cements showed mixed failures but adhesive-based resin cements showed adhesive failures.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.48.2-48.2
• /
• 2011

열전재료는 열과 전기에너지의 상호 변환이 가능한 재료로 이를 이용한 응용제품의 개발이 크게 주목을 받고 있으며, 특히 $Bi_2Te_3$계 합금의 경우 상온에서 가장 우수한 성능지수를 가지는 재료로 많은 연구가 진행되고 있다. 그러나 기존의 $Bi_2Te_3$계 합금은 일방향응고법으로 제조되어 많은 시간과 비용을 필요로 하고, 특히 C축의 Van der Waals 결합으로 인해 기계적 강도가 약하다는 단점이 있었다. 최근 분말야금법을 이용하여 기계적강도를 높이고, 격자산란에 의한 열전도도의 감소로 성능지수를 높일수 있는 방법들이 제시되고 있다. 본 연구에서는 급속응고공정인 가스분무법을 이용하여 n-type의 $95%Bi_2Te_3-5%Bi_2Se_3$분말을 제조하였고, 이 재료의 경우 성형조건에 따라 조직이 쉽게 변하기 때문에 이를 제어하기 위해 단시간동안 고압으로 성형가능한 자기펄스압축성형법(Magnetic Pulsed Compaction)을 이용하여 성형체를 제조하였다. 제조된 성형체는 밀도를 증가시키고 결정립성장을 억제시킬수 있는 방전플라즈마소결법(Spark Plasma Sintering)을 이용하여 소결체로 제조되었으며, 각각의 공정이 열전성능에 미치는 영향을 고찰하였다. OM (Optical Microscope) 및 SEM (Scaning Electric Microscope)을 이용하여 미세구조를 관찰하였고 XRD (X-Ray Diffraction)를 이용하여 상의 변화를 분석하였으며, 상온에서 경도를 측정함으로서 공정조건에 따른 기계적강도를 비교하였다. Seebeck계수는 시편의 양단에 온도차를 주어 발생하는 기전압을 측정하여 계산하였고, 전기비저항은 4point probe방법으로 측정하였다. 전하이동도 및 전하농도는 Hall측정으로부터 구하였고 열전도도를 측정하여 종합적인 열전성능을 평가하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.418-424
• /
• 2016

This study is an experimental study on the recycling of bottom ash in coal ash discharged from a thermal power plant. Bottom ash has limited research on recycling because it has more porous and higher water absorption ratio than fly ash. In this paper, the bottom ash was pulverized to a specific surface area of $4,000cm^2/g$ in order to use as a binder, and the flow, compressive strength test and microstructure analysis of the bottom ash based geopolymer mortar were performed. The flow measurement results of the geopolymer mortar showed that the flow rate was improved by increasing mixing water as the molar concentration of activator was increased. Compressive strength increased with increasing curing temperature and molar concentration. Through the microstructure analysis, we could confirm the geopolymer gel produced by the reaction of the condensation polymerization. It is considered that it is possible to make the bottom ash based geopolymer concrete through proper molar concentration of activator and high temperature curing.

• Korean Journal of Dental Materials
• /
• v.45 no.4
• /
• pp.301-310
• /
• 2018

The purpose of this study is to evaluate the compatibility of universal adhesives with two dual-cured resin cements. Eighty human molars were divided into eight groups. Tooth was embedded in self-curing acrylic resin and sectioned horizontally to exposure dentine surface. After polishing with 600-grit SiC paper, adhesives were applied. All-Bond Universal (Bisco), G-premio bond (GC), Scotch-bond universal (3M ESPE), Scotch-bond Multipurpose (3M ESPE) were used in this study. Calibra (Dentsply) as a conventional dual-curing resin cement and RelyX Ultimate (3M ESPE) as an amine free resin cement were used. The adhesives and the cements were applied according to the manufacturer's instructions. Final specimens were cylinder (diameter 2mm, height 3mm) shape. After storing in distilled water at $37^{\circ}C$ for 7 days the shear bond strength (SBS) test was performed. There was no significant difference in shear bond strength between the adhesives when RelyX Ultimate was used (p>0.05). However, when Calibra used with Scotch-bond Multipurpose and All-Bond Universal were used, statistically higher SBS was observed, as compared to the groups which Calibra cements with G-premio bond and Scotch-bond universal adhesive (p<0.05) were used. Within the limitations of this study, RelyX Ultimate resin cement was compatible with universal adhesives of various pH. All-Bond Universal adhesive was compatible with a resin cement containing the tertiary amine.

• Restorative Dentistry and Endodontics
• /
• v.32 no.4
• /
• pp.365-376
• /
• 2007

The purpose of this study was to evaluate the effect of different etching times on microtensile bond strength (${\mu}TBS$) to dentin both initial and after thermocycling with 3 different types of total-etching adhesives. Fifty four teeth were divided into 18 groups by etching times (5, 15, 25 sec), adhesives types (Scotchbond Multipurpose (SM), Single Bond (SB), One-Step (OS)) and number of thermocycling (0, 2,000 cycles). Flat dentin surfaces were prepared on mid-coronal dentin of extracted third molars. After exposed fresh dentin surfaces were polished with 600-grit SiC papers, each specimen was acid-etched with 35% phosphoric acid (5, 15, 25 sec) and bonded with 3 different types of total etching adhesives respectively. Then, hybrid composite Z-250 was built up. Half of them were not thermocycled (control group) and the ethers were subjected to 2,000 thermocycle (experimental group). They were sectioned occluso-gingivally into $1.0\;{\times}\;1.0\;mm^2$ composite-dentin beams and tested with universal testing machine at a crosshead speed of 1.0 mm/min. Within limited data of this study, the results were as follows 1. There was no statistically significant difference in ${\mu}TBS$ between the thermocycled and non-thermocycled groups, except for both SM and SB etched for 25 sec. 2. In thermocycled SM and SB groups, bond strength decreased by extended etching time. In total etching systems, adhesive durability for dentin could be affected by type of solvents in adhesive and etching time. Especially, extended etching time may cause deteriorate effects on bond strength when ethanol-based adhesive was used.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.3
• /
• pp.127-132
• /
• 2014

$Y_2O_3$-BN ceramic composites were fabricated from the slurries of yttria powder with average particle size of 3~10 ${\mu}m$. The slurry was fabricated by mixing PVA binder, NaOH for Ph control, PEG, BN powder and $Y_2O_3$ powder. The mixed $Y_2O_3$ powders were obtained by spray drying process from the slurry. The $Y_2O_3$-BN composite specimen was shaped in size of ${\O}14mm$ and then sintered at $1550^{\circ}C$ and $1600^{\circ}C$, respectively. The characteristics, microstructure, purities, densities, bulk resistance, thermal expansion, hardness and plasma resistance of the $Y_2O_3$-BN composites were investigated with the function of BN contents and sintering temperature.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.186-192
• /
• 1999

Dang-Chin feldspar powder with the mean particle size of 9.1 $\mu\textrm{m}$ was added to the synthesized mullite powder with the particle size of +325∼-200 mesh and the powder compact was prepared by PLPP(pressureless powder packing method). Densification behaviors were observed in sintering temperature range of 1200∼1400$^{\circ}C$. The binder solution of 4% PVA was infilterated into packed powder to the suitable strength. The PLPP method makes it possible to form compacts without clay as plasticizer. Therfore there was no defect caused by phase transition after sintering. Additionally, we observed the dense microstructure by the melting of feldspar. When the mullite compacts with feldspar of 30% were sintered at 1300$^{\circ}C$-4 hrs, we obtained the dense microstructure with zero water absorption and porosity <1%. When these compacts were sintered longer than 4 hrs at 1300$^{\circ}C$ or higher than 1400$^{\circ}C$, the examggerated grain growth of mullite was observed.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.4
• /
• pp.321-330
• /
• 2020

The addition of a limestone filler(LF) to fill into the voids between cement and aggregate particles can reduce the cementitious paste volume. In previous studies, it has been found that the addition of LF to reduce the cementitious paste volume would substantially increase the compressive strength, and reduce the heat generation. This paper aim to evaluate the influence of LF contents on the hydration kinetics and compressive strength. Hydration kinetics were evaluate using heat of hydration, ignition loss and thermal analysis. The heat of hydration was measured using Isothermal Calorimetry. The degree of hydration was measured using ignition loss. Hydration product analysis was carried out by Thermal Gravimetric and Differential Thermal Analysis. The results show that the addition of LF reduces not only the initial setting time and heat of hydration peak, also degree of hydration and rate of strength development at early age increase with the addition of LF. It can be concluded the LF fills the pore between cement particles due to formation of carboaluminate, which may accelerate the setting of cement pastes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.15-21
• /
• 2008

SiC has an excellent resistance to oxidation and corrosion, high temperature strength and good thermal conductivity. However, it is difficult to density because of its highly covalent bonding characteristics. Hot-press sintering process was applied to fabricate fully densified SiC ceramics with carbon and boron addition as a sintering additive. The addition of carbon improved the mechanical properties of SiC because it could induce a fine and homogeneous microstructure by the suppression of abnormal growth of SiC grain. Also, the addition of carbon could control the phase transformation of SiC. The phase transformation of 6H to 4H increased with sintering temperature but the addition of carbon decreased that kind of phase transformation.