• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.781-787
• /
• 2014

The dimensionless extinction constants of particulate matter for F-76 diesel and JP-8 aviation fuels were measured at both 633 nm and 853 nm in the transmission cell where the simultaneous gravimetric measurement of PM concentration is compared to the light extinction measurement. For the F-76 diesel PM, the average value of the dimensionless extinction constants at 633 nm was 8.8 whereas that of the dimensionless extinction constants for JP-8 was 9.8 at the same wavelength. As the wavelength is increased to 853 nm, the average value for the F-76 diesel was reduced to 8.2 whereas that for JP-8 was decreased to 8.9.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.136-142
• /
• 2004

A homogeneous and stable ZnO sol was prepared by dissolving the zinc acetate dihydrate(Zn(CH$_3$COO)$_2$$.$2H$_2$O) in solution of isopropanol((CH$_3$)$_2$$.$CHOH) and monoethanolamine(MEA:H$_2$NCH$_2$CH$_2$OH). ZnO thin films were prepared by sol-gel spin-coating method and investigated for c-axis preferred orientation and physical properties with preheating temperature. The c-axis growth had a difference as increaing preheating temperature. ZnO thin film preheated at 275$^{\circ}C$ and post-heated at 650$^{\circ}C$ was highly oriented along the (002) plane. After preheating at 200∼300$^{\circ}C$ and post-heating at 650$^{\circ}C$, the transmittance of ZnO thin films by UV-vis. measurement was over 85% in visible range and exhibited absorption edges at about 370 nm. The optical band gap energy was obtained about 3.22 eV, The photoluminescence emission characteristics of ZnO thin film preheated at 275$^{\circ}C$ and post-heated at 650$^{\circ}C$ was found to orange emission(620 nm, 2.0 eV) by PL measurement, which revealed the possibility for application of inorganic photoluminescence device.

• Journal of Adhesion and Interface
• /
• v.22 no.2
• /
• pp.57-62
• /
• 2021

Recently, the atomically thin two-dimensional transition-metal dichalcogenides (TMDs) have received considerable attention for the application to next-generation semiconducting devices, owing to their remarkable properties including high carrier mobility. However, while a technique for growing graphene is well matured enough to achieve a wafer-scale single crystalline monolayer film, the large-area growth of high quality TMD monolayer is still a challenging issue for industrial application. In order to enlarge the size of single crystalline MoS₂ monolayer, here, we systematically investigated the effect of process parameters in molten-salt-assisted chemical vapor deposition method. As a result, with optimized process parameters, we found that single crystalline monolayer MoS₂ can be grown as large as 420 ㎛.

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.2
• /
• pp.120-127
• /
• 2011

Purpose: The purpose of this study was to examine the effects of chromium chloride addition on coloration, mechanical property and microstructure of 3Y-TZP. Materials and methods: Chromium chloride was weighed as 0.06, 0.12, and 0.25 wt% and each measured amount was dissolved in alcohol. $ZrO_2$ powder was mixed with each of the individual slurry to prepare chromium doped zirconia specimen. The color, physical properties and microstructure were observed after the zirconia specimen were sintered at $1450^{\circ}C$. In order to evaluate the color, spectrophotometer was used to analyze the value of $L^*$, $C^*$, $a^*$ and $b^*$, after placing the specimen on a white plate, and measured according to the International Commission on Illumination (CIE) standard, Illuminant D65 and SCE system. The density was measured in the Archimedes method, while microstructures were evaluated by using the scanning electron microscopy (SEM) and XRD. Fracture toughness was calculated Vickers indentation method and indentation size was measured by using the optical microscope. The data were analyzed with 1-way ANOVA test (${\alpha}$ = 0.05). The Tukey multiple comparison test was used for post hocanalysis. Results: 1. Chromium chloride rendered zirconia a brownish color. While chromium chloride content was increased, the color of zirconia was changed from brownish to brownish-red. 2. Chromium chloride content was increased; density of the specimen was decreased. 3. More chromium chloride in the ratio showed increase size of grains. 4. But the addition of chromium chloride did not affect the crystal phase of zirconia, and all specimens showed tetragonal phase. 5. The chromium chloride in zirconia did not showed statistically significant difference in fracture toughness, but addition of 0.25 wt% showed a statistically significant difference (P<.05). Conclusion: Based on the above results, this study suggests that chromium chlorides can make colored zirconia while adding in a liquid form. The new colored zirconia showed a slight difference in color to that of the natural tooth, nevertheless this material can be used as an all ceramic core material.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.32.2-32.2
• /
• 2009

21세기의 IT 및 NT를 선두 하게 될 나노소자의개발은 10년 전부터 아주 활발히 연구되고 있다. 최근, 이러한 나노소자의 연구 가운데 주목할 만한 물질이 ZnO 이다. ZnO를 기반으로 한 나노구조는 여러 성장 법으로 성장이 용이하고, 그 물리적, 광학적 특성이 우수하여 광 전소자 응용에 크게 이바지할 물질로 관심을 끌고 있다. 이 가운데 나노선은 소자제작이 용이해 가장 많이 이용되고 있다. 나노선을기반으로 한 소자제작은 bottom-up 공정을 지향하고 있지만, 아직은 top-down 방식이 소자제작의 주류를 이루고 있다. 특히, 나노선 FET 소자제작 시에는 여전히 top-down이 사용되고 있으며, 채널로 사용되는 나노선의 어레이공정은 소자제작 시 가장 큰 어려움으로 대두되고 있다. 하지만, 이러한나노선의 수평 어레이 공정을 감소시킬 구조로 기판에 수평으로 배열된 나노월 구조가 제안되고 있다. 나노월구조는 어레이 공정 수를 크게 감소시켜 생산가격 면에서 큰 이점을 가져올 것으로 생각된다. 하지만, 이러한 ZnO 나노월은 GaN 기판에 한정하여 성장되고 있으며, 일부 Si 기판 위에 성장할지라도나노 사이즈가 아닌 마이크로 사이즈의 거친 표면을 가지는 박막구조로 보고되었다. 때문에, 가격적으로 비싸고 응용성이 제한적인 비전도성 기판을 대신하여, 가격이 저렴하고 응용성이 넓은 Si과 같은 전도성 기판에 나노월 구조를 성장하는 기술이 요구되고 있다. 본 연구에서는 Mg의 도입으로 자발적으로 형성된 비정질 MgO층 위에 상 분리된 MZO 비정질-단결정 층들을 이용하여 어떠한 기판에서도 나노월 구조가 성장할 수 있는 기반 기술을 소개한다.

• Journal of Sericultural and Entomological Science
• /
• v.29 no.2
• /
• pp.58-66
• /
• 1987

This study was investigated on the effect of degumming of cocoon shell, raw silk yarn and grey silk crepe by use of Papain, comparing with soap, soda and soap-soda. The obtained results may be summarized as follows : 1. Degumming loss, when the pretreatment was done, was completed by Papain more than by alkali. 2. Lousiness result of Papain degummed silk yarn was apt to be improved more than that of alkali degummed one. 3. As a result of tensile property test, elasticity and resilience of Papain degummed crepe were good compared to those of alkali degummed one. 4. Not only bending rigidity of Papain degummed crepe was reduced more than that of alkali degummed one but also hysteresis of bending moment was decreased in papain degummed crepe. 5. Handle of Papain degummed crepe was superior to that of alkali degummed one.

• Korean Journal of Materials Research
• /
• v.2 no.6
• /
• pp.417-427
• /
• 1992

Silicon ion implantation was performed to LPCVD amorphous Si films and the low temperature annealing process followed with various conditions to find the optimal physical properties by studying recrystallization behavior. The uniformity of the recrystallized films was inspected by optical microscopy and for this purpose, new KOH: (IPA) : $H_2$O: $K_2$C${r_2}{O_7}$, etchant was developed. XRD and TEM results showed that the crystallites were grown as a form of dendrite with (111) preferred orientation, and the grain size was increased with dose concentration. The maximum grain size was obtained when the 3${\times}{10^{15}}$c$m^2$ implanted amorphous Si film was recrystallized at 55 $0^{\circ}C$for more than 40 hrs and at this condition the grain size was 3.2${\mu}$m.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.111-111
• /
• 2008

태양전지는 태양에너지를 직접 전기에너지로 변환시켜주는 광전 소자로서 구조적으로 단순하고 제조 공정도 비교적 간단하지만, 실용화를 위해서는 비용적인 측면이 많은 걸림돌이 되고 있다. 기존의 실리콘 태양전지는 낮은 광흡수율, 고비용임에도 불구하고 가장 많이 활용되고 있는 태양전지 기술이다. 그러나 태양전지의 경제성 향상과 실용화를 위해서는 기존의 실리콘 태양전지 보다 고효율 및 고신뢰도의 박막형 태양전지의 개발이 필요하다. 박막헝 태양전지의 재료로는 비정질 실리콘, 다결정 실리콘. CIGS, CdTe 등이 있다. 그 중에서도 박막형 태양전지에 광흡수층 물질로는 밴드갭 에너지 (l.4eV 부근), 변환 효율, 경제성 등을 고려했을 때 II-VI족 화합물인 CdTe가 가장 적합한 것으로 각광받고 있다. 하지만 아직까지 실리콘 태양전지에 비해 효율이 많이 떨어지는 단점을 가지고 있기 때문에 효율을 더 끌어올리기 위한 연구가 활발히 진행되고 있는 실정이다. 또한 CMP(chemical mechanical polishing) 공정은 반도체 박막 분야뿐만 아니라 물리, 화학 반응의 기초 연구에도 널리 응용이 되는 기술로써, 시료와 연마 패드 사이의 회전마찰에 의한 기계적 연마와 연마제 (abrasive) 에 의한 화학적 에칭으로 박막 표면을 평탄화하는 기술이다. 본 연구에서는 sputtering 법에 의해 증착된 CdTe 박막에 CMP 공정을 적용하여 표면 특성을 개선한 뒤 태양전지 변환 효율과 직접적인 연관성을 가지고 있는 표면 및 광특성의 변화를 CMP 공정 전과 후로 비교하였다. 표면의 변화를 관찰하기 위해서 AFM(atomic forced microscope) 과 SEM(scanning electron microscopy) 을 이용하였으며, 광특성의 비교를 위해서 흡수율과 PL특성을 측정하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.5
• /
• pp.35-45
• /
• 1981

An asymptotic solution of electromagnetic waves scattered by a right-angled dielectric wedge for plane wave incidence is obtained. Scattered fields are constructed by waves reflected and refracted from dielectric interfaces (geometric-optical fields) and a cylindrical wave diffracted from the edge. The edge diffracted field is obtained by adding a correction to the edge diffraction of physical optics approximation, where the correction field is calculated by solving a dual series equation amenable to simple numerical calculation. Validity of this result is assured by two limits of relative dielectric constant $\varepsilon$ of the wedge. The total asymptotic field calculated results in a Rawlins' Neumann series solution for small $\varepsilon$, and the edge diffraction pattern is shown to approach that of a perfectly conducting wedge for large $\varepsilon$. Calculated field patterns are presented and the accuracy of physical optics approximation is discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.46-53
• /
• 2008

In general, the cassegrain dual offset reflector is used for the satellite communication antenna, but is analyzed as the reflector system for the CPTR(Compact Payload Test Range) facility in here. The near-field at the test zone of the CPTR is obtained by using the physical optics approximation. The CPTR has to provide a uniform plane wave with the minimum amplitude and phase ripple and the low cross polarization. Therefore, in this paper, the near-field pattern are calculated, and the ripple and taper of the field and the cross polarization are investigated with the variation of the reflector geometry and the position of the test region. Especially, the cross polarization of the antenna axis direction which is not found in the satellite reflector antennas is investigated.