• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.36-40
• /
• 2012

We have developed the detection method of the resonance frequency of micro/nano mechanical resonator using optical method. The optical interferometery method enabled us to detect the displacement change of resonators within several nm scale. The micro mechanical resonator was produced by attaching a micro mechanical cantilever to a piezo ceramic. The mass of cantilever was increased by evaporating Au using electron beam evaporator and the mass variation was estimated by detecting the resonance frequency changes.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.3
• /
• pp.219-227
• /
• 2016

In this study, we have proposed a method of monitoring of bridges under construction in view of the long-term behavior of the prestress concrete bridge of which the Free Cantilever Method is applied. As a method to confirm the ability of the long-term behavior of the concrete box girder, temperature sensors and strain gauges were installed, and the measured data was used to calculate creep coefficient. Moreover, we have measured the stress of the concrete box girder during construction which was applied with creep coefficient and compared with the changes in temperature to analyze the vertical displacement along the segment. In conclusion, monitoring of the FCM bridge during construction in consideration of the long-term behavior can be analyzed efficiently by suing temperature and displacement data without the use of laser displacement meter or laser delfectometer.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.496-503
• /
• 2016

Leakages at plant structures of power and petrochemistry plants have led to casualties and economic losses. These leakages are caused by fatigue failure of pipelines and their wall thickness. Vibration measurement methods for plant pipelines mainly use acceleration and laser sensors. These sensors are difficult to install and operate and thus lead to an increase in operational cost especially for wide area surveillance. Recently, measurements of leak and vibration displacements using cameras have attracted the interest of many researchers. This method has advantages such as simple installation, long distance monitoring, and wide area surveillance. Therefore, in this paper, we have developed a system that can measure the leakage and vibrational displacement by using a camera. Furthermore, the developed system was verified with experimental data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2237-2242
• /
• 2014

As Single households increases for reason of communication development, extending human life, there are many problems occuring all over the world. In order to solve this problem with an invasion of privacy and manintain a healthy life, this paper suggest non-contact type bio-signal measurement system using IR-Radar, displacement sensor and Pan-Tilt system. The proposed system can increse the distance of measured respiration from 1m to over 8m, which is comprised of two IR-Radar for location tracking, one displacement sensor for non-contact type bio-signal measurement and one stepping motor drive system. The proposed system is verified through experiments and were confirmed the possibility.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.46-52
• /
• 2011

A confocal microscope was developed utilizing a scanning sample stage based on a home-built double-compound flexure guide. A scanning sample stage with nano-scale resolution consisted of a double leaf spring based flexure, a displacement amplifying lever, a Piezo-electric Transducer(PZT) actuator and capacitance sensors. The performance of the two-axis stage was analyzed using a commercial finite element method program prior to the implementation. A single line laser was employed as the light source along with the Photo Multiplier Tube(PMT) that served as the detector. The performance of the developed confocal microscope was evaluated with a mouse ear skin imaging test. The designed scanning stage enabled us to build the confocal microscope without the two optical scanning mirror modules that are essential in the conventional laser scanning confocal microscope. The elimination of the scanning mirror modules makes the optical design of the confocal microscope simpler and more compact than the conventional system.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.3
• /
• pp.11-19
• /
• 2009

Recently, concerns relating to the maintenance of large structures have been increased. In addition, the number of large structures that need to be evaluated for their structural safety due to natural disasters and structural deterioration has been rapidly increasing. It is common for the structural characteristics of an older large structure to differ from the characteristics in the initial design stage, and changes in dynamic characteristics may result from a reduction in stiffness due to cracks on the materials. The process of deterioration of such structures enables the detection of damaged locations, as well as a quantitative evaluation. One of the typical measuring instruments used for the monitoring of bridges and buildings is the dynamic measurement system. Conventional dynamic measurement systems require considerable cabling to facilitate a direct connection between sensor and DAQ logger. For this reason, a method of measuring structural responses from a remote distance without the mounted sensors is needed. In terms of non-contact methods that are applicable to dynamic response measurement, the methods using the doppler effect of a laser or a GPS are commonly used. However, such methods could not be generally applied to bridge structures because of their costs and inaccuracies. Alternatively, a method using a visual image can be economical as well as feasible for measuring vibration signals of inaccessible bridge structures and extracting their dynamic characteristics. Many studies have been conducted using camera visual signals instead of conventional mounted sensors. However, these studies have been focused on measuring displacement response by an image processing technique after recording a position of the target mounted on the structure, in which the number of measurement targets may be limited. Therefore, in this study, a model experiment was carried out to verify the measurement algorithm for measuring multi-point displacement responses by using a DIC (Digital Image Correlation) technique.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.169-174
• /
• 2019

Flexure joints are recently used in the ultra-precision mechanism for a telecommunication mirror stage. Flexure joints have several advantages coming from their monolithic characteristics. They can be used to reduce the size of manipulators or to increase the precision of motion. In our research, 6 dof(degree of freedom) mechanism is suggested for micrometer repeatability using a flexure mechanism. To design the 6-dof motion, the 2-dof planar mechanism are designed and assembled to make the 6-dof motion. To achieve a certain performance, it is necessary to define the performance of mechanism that quantifies the characteristics of flexure joints. This paper addresses the analysis and design of the 6-dof parallel manipulator with a flexure joint using a finite element analysis tool. To obtain experimental result, CCD laser displacement sensor is used for the total displacement and the stiffness for the 6-dof flexure mechanism.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.4
• /
• pp.271-274
• /
• 2013

Inclinometer sensors are widely applied in many fields. Especially in the field of construction of high-rise buildings also measure the horizontal and vertical help has been applied to monitor. Recent micro electro-mechanical system(MEMS) technology with the development of the many sensors have been developed. In this paper, a MEMS inclinometer is based on a MEMS accelerometer. The sensor can measure the angle of inclination using the relationship between static acceleration and gravity acceleration from an accelerometer. From this principle, inclinometer has been developed that has more accurate. The accuracy is proved by the experiment with laser displacement. Results in the experiment express high-accuracy, stability and economics of MEMS inclinometer. In conclusion, wireless MEMS inclinometer sensor is expected to be applicable in the areas of construction and many other industries with accurate and convenient monitoring system.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2011-2013
• /
• 2004

본 논문은 그루빙(grooving),타이닝(tinning),텍스쳐(texture) 등의 포장 도로의 표면 상태를 고성능의 레이저 변위센서를 사용하여 정밀하게 측정하고, 측정한 표면 상태를 객관적으로 평가하는 장비 개발에 관한 논문이다. 본 논문에서는 실제 평가 장비 차량을 만들기에 앞서 전체 시스템을 설계하고, 실내에서 차량과 도로의 모사 장비를 만들어 실험하였다. 본 실험에서는 오실로스코프와 DAQ (Data Aquisition) 보드를 사용하였다. LabView로 선호처리 프로그래밍을 하여 컴퓨터 화면에 GUI 형태로 나타내었다. 측정 데이터는 컴퓨터의 저장 공간에 저장하여 후처리를 가능하게 하였다. 또한, 실제 평가 장비 차량에 장착하게 될, GPS(Global Positioning System) 시스템으로 부터 실시간으로 평가 장비 차량의 이동거리 데이터를 얻었다. 실험 결과 차량이 80km/h로 주행할 때 도로 표면 타이닝의 폭과 깊이가 평균 9.67% 오차를 보였으며, 이동거리는 0.03% 이내의 오차를 보여 만족할 만한 결과를 얻었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.115-118
• /
• 2005

A workpiece with a large surface area is likely to be uneven due to form error and waviness. These geometric disturbances can cause inaccurate micro shapes to be formed when micro features are micro-grooved into the surface and cause the resulting workpiece to fail to function as desired. Thus, real-time measurement and compensation is required to guarantee the form accuracy of micro features while machining a workpiece with a large surface area. In this study, a method is suggested for real-time measurement of geometric error for the micro grooving of a large flat surface using a laser displacement sensor. The measurements are demonstrated for the workpieces with large surface areas and the experimental results show that the waviness and form error are well detected.