• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.12
• /
• pp.777-784
• /
• 2016

All-vanadium redox flow batteries (VRFBs) are used as energy storage systems for multiple intermittent power sources. The performance of the VRFBs depends on the materials and operating conditions. Hence, performance characterization is of great importance in the development of the VRFBs. This paper proposes a method for determining the maximum current density based on stoichiometric ratios. A laboratory-scaled VRFB with a projected electrode area of $25cm^2$ is electrically charged when the state of the charge has begun from 0.6. The operating conditions, such as current density and volumetric flow rate are important in the test, and the maximum current density is influenced by the mass transfer coefficient. The results show that increasing the electrolyte flow rate from 5 mL/min to 60 mL/min enhances the maximum current density up to $520mA/cm^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.256-259
• /
• 2005

본 연구에서는 기존 니켈 활성성분만의 알루미나담지 촉매에 비해 고온에서의 수소를 사용한 환원 전처리 과정을 거치지 않고도 높은 반응활성을 나타내며, 반응 중 탄소침적에 대한 촉매 저항성에서도 우수한 결과를 나타낸 루테늄-니켈 촉매에 대해보고 하고자 한다. 메탄 수증기 개질 반응을 통해, 루테늄을 최종적으로 담지한 알루미나 담지니켈계 촉매는 별도의 전처리과정 없이 $650^{\circ}C$에서부터 높은 반응성을 보였으며, 루테늄과 니켈을 동시에 담지한 경우보다 더 우수한 활성을 나타내었다. Ru의 담지량을 달리한 실험에서는$RU(0.5)/Ni(20)/Al_2O_3$ 촉매가 가장 높은 활성을 보였다. $H_2-TPR$ 분석 결과, $Ru(0.5)/Ni(20)/A1_2O_3$촉매의 경우 세 가지 환원 피크가 나타났으며, $Ni(20)/A1_2O_3$촉매와 비교해 볼 때, 저온(<$130^{\circ}C)$에서 환원가능한 $RUO_2$의 존재를 확인할 수 있었다. 담지된 RU은 분산도가 높아, XRD분석 결과에서 Ru이나 $RuO_2$의 특성 피크가 존재하지 않았다. 또한 $650^{\circ}C$에서 10시간 개질반응 후 얻어진 촉매에 대해 $O_2-TGA$를 분석한 결과, $Ni(20)/Al_2O_3$촉매는 $-7.2wt\%$ 정도의 큰 무게 감소를 보였으며, 이는 촉매 표면에 생성된 carbon tube에 의한 것임을 SEM 분석을 통해 알 수 있었다 이에 반해, $Ru(0.5)/Ni(20)/Al_2O_$ 촉매는 $O_2-TGA$시 $0.3wt\%$ 정도 무게 증가에 그쳤으며, SEM 분석상 carbon tube의 생성이 크게 억제되었음을 알 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.361-363
• /
• 2008

탄소 개질반응은 $1200^{\circ}C$(도1) 이상에서 모든 탄화물질과 수분 또는 $CO_2$ 사이에서 흡열/환원반응이 일어나서 합성가스를 생성한다. 개질반응로는 산화반응로와 연결되어, 수소가스와 CO 가스의 혼합인,합성가스가 산화반응로 내에서 산소가스와 연소하여 열과 $H_2O+CO_2$를 생성하여 환원 반응로 내로 유입되어, 환원 반응로를 $1200^{\circ}C$ 이상으로 유지하고, $H_2O$와 $CO_2$는 석탄 속의 모든 탄소를 CO로 개질한다(도2). 동시에 수소가스가 생성되어 합성가스를 생성하게 된다. 석탄 속의 비탄소 물질인 슬래그(Slag)는 개질로 내에 남게 되는데, 개질로를 슬래그 융점(non-fluid point) 이하에서 고체상태로 포집함으로서 Fly-ash로 처리된다. 개질로 내의 온도를 $1200{\sim}1300^{\circ}C$(석탄 슬래그 융점)로 유지함으로서 개질반응이 지속되어 합성가스가 생성된다. IGCC 시스템에서는 합성가스를 가스터빈 속에서 $O_2E가스와 연소하여 고온의 가스를 생성하여 터빈을 가동해 발전을 하고 배출가스를 $1500{\sim}1700^{\circ}C$에서 배출한다. 재래식 IGCC(도4)에서는 ${\sim}1500^{\circ}C$의 배출가스를 열교환 시스템에 의해 증기를 생성하여 Steam turbine(증기터빈)을 가동하여 추가 전력을 생산했다. 그러나 본 시스템에서는 배출가스(증기와 $CO_2E 가스)를 위의 개질로에 유입하여 개질로 온도를 $1200{\sim}1300^{\circ}C$로 유지함으로서 더 많은 합성가스를 생성 하게 된다(도3). 이렇게 하여 Oxidation-reduction cycle을 형성하게 된다. 새로운 IGCC 시스템에서 가스 터빈의 배출가스가 석탄 개질로에 연결되고 석탄개질로의 합성가스 출구가 가스터빈의 가스 입구에 연결됨으로서,외부에너지 주입 없이 지속 가능한 가스화 반응과 터빈 사이클(Cycle)을 완성하여 IGCC 시스템의 석탄 열효율을 1단계 상승시켰다. 이렇게 설계된 석탄가스화기는 Lurgi형 석탄가스화 기와 달리 석탄개질반응의 효율을 높일 수 있고, 슬래그 처리가 간단하기 때문에 석탄가스화기가 소형화 될 수 있으며 슬래그(Slag)용융에 따른 석탄가스화기의 외벽손상을 피할 수 있다.

• Resources Recycling
• /
• v.21 no.3
• /
• pp.21-27
• /
• 2012

In order to make high-purity ferro-manganese from $Mn_3O_4$ dust, the application of aluminothermy process to the reduction of $Mn_3O_4$ dust was investigated in previous work. The result showed the fact that can be obtained high purity ferro-manganese which have over about 93% of manganese content and lower impurities such as C, P, S than those of KS D3712 specification. The addition of silicon powder instead of aluminum powder was investigated as reductant in the thermite reaction process of $Mn_3O_4$ dust in this work because its production cost is lower than that of aluminum powder. In case of addition of silicon powder only as reductant, the experimental result showed the unstable ignition and no thermite reaction of mixture, but in case of simultaneous addition of silicon and aluminum powders as reductant, showed the fact that can be obtained high purity ferro-manganese which have much low content of impurities such as C, P, S component.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.897-900
• /
• 2008

Some substances of cement could make underestimate concentration of hexavalent chromium(Cr(VI)) as they reduce Cr(VI) to Cr(III) in acidic condition during the determination of Cr(VI) content in cement. The reduction of Cr(VI) increased with elapsed time after acidification in this study. The reduction rate varied with various cements. From our result, we can conclude that simultaneous additions of acid and DPC were required for the accurate measurement of Cr(VI) in cement. The high recovery rate of 94.3 to 106.7% with the simultaneous acid-DPC addition method can also support our conclusion.

• Clean Technology
• /
• v.18 no.4
• /
• pp.410-418
• /
• 2012

The performance of the ammonia injection gun (AIG) used for maximizing the utilization of reducing agent in the selective catalytic reduction (SCR) system is decided by several parameters such as the pattern of flow distribution, geometry of the air distribution manifold (ADM) and the array and geometry of nozzles. In the study, the uniformity of jet flows from the nozzles in AIG was analyzed statistically by using the computational fluid dynamics (CFD) method to evaluate the role of design parameters on the performance of the SCR system. The uniformity of jet flows from the nozzles is being deteriorated with increasing the supplying flow rate to the AIG. Distribution rates to each branch pipe become lower with decreasing distance to the header, and flow rates from nozzle are also reduced with decreasing distance to the header. The uniformity of jet flows from nozzles becomes stable significantly when the ratio of summative area of nozzles to each sectional area of the branch pipe is below 0.5.

• Korean Journal of Soil Science and Fertilizer
• /
• v.19 no.1
• /
• pp.63-69
• /
• 1986

1. Chemical components of fresh tobacco leaves at topping stages were affected variously by fertilizer application level. The more fertilizers were applicated, the higher nitrogen content of leaves was shown regardless of the soil fertility, but phosphorus content was not affected either by phosphorus rate or soil fertility. Potassium content was higher in the leaves grown in fertile soil than infertile at the same application rate. 2. Maturation of tobacco leaves was delayed by applying high level of nitrogen fertilizer, especially in fertile soil. The excessive accumulation of nitrogen in tobacco leaves at later stage of growth resulted in poor quality index for the high content of nicotine and low content of reducing sugar in cured leaves. 3. Nicotine content of cured leaf was increased significantly as nitrogen content increased, regardless of soil fertility, but reducing sugar content was reduced. Nicotine and reducing sugar content of cured leaf were higher in fertile than in infertile soil. 4. Resulting from the facts that nicotine contents were negatively correlated and reducing sugar contents were positively correlated with grading value (Won/Kg), authors suggested that grading index (Won/Kg) of the Office of Monopoly be based on quality index from chemical components of cured leaves.

• Clean Technology
• /
• v.25 no.1
• /
• pp.63-73
• /
• 2019

Numerical analysis was done to evaluate the chemical reaction and the reduction rate inside of selective non-catalytic reduction to denitrification in combustion process. The $NO_X$ reduction in selective non-catalytic reduction is converted to not only nitrogen but also nitrous oxide. Simultaneous $NO_X$ reduction and nitrous oxide generation suppressing is required in selective non-catalytic reduction because nitrous oxide influences the global warming as a greenhouse gas. The current study was performed compare the computational analysis in the same temperature and amount of NaOH, and in comparison with the previous research experiments and confirmed the reliability of the computational fluid dynamics. Additionally, controlling the addition amount of NaOH to predict the $NO_X$ reduction efficiency and nitrous oxide production. Numerical analysis was done to check the mass fraction of each material in the measurement point at the end of selective non-catalytic reduction. Experimental Value and simulation value by numerical analysis showed an error of up to 18.9% was confirmed that a generally well predicted. and it was confirmed that the widened temperature range of more than 70% $NO_X$ removal rate is increased when the addition amount of NaOH. So, large and frequent changes of the reaction temperature waste incineration facilities are expected to be effective.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.25-37
• /
• 2020

In this study, hybridization of graphene oxide and metal was carried out by the functional groups containing oxygen and thermal treatment for reduction in order to enhance the electrical conductivity and magnetic properties of graphene materials. Graphene-metal hybrid materials were synthesized using the oxygen-containing functional groups (-OH, -COOH and so on) on the surface of graphene oxide by replacing them with metal ions via ion exchange method as well as thermal reduction. The metals used in this study were Fe, Ag, Ni, Zn, and Fe/Ag, and it was confirmed that metal particles of uniform size were well dispersed on the graphene surface through SEM, TEM, and EDS. All of the metal particles on the graphene surface had an oxide-crystalline structure. To check the electrical properties, sheet resistance of the rGO-metal hybrid sample was measured on the PET film made by the dip-coating, and the specific resistance was calculated by measuring the thickness of the specimen through SEM. As a result, the specific resistance was in the range of 2.14×10-5 and 3.5×10-3 ohm/cm.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.77-82
• /
• 2010

Effects of evaporation processes and a reduction annealing on thermoelectric properties of the Sb-Te thin films prepared by thermal evaporation have been investigated. The thin film evaporated by using the powders formed by crushing a $Sb_2Te_3$ ingot as an evaporation source exhibited a power factor of $2.71{\times}10^{-4}W/m-K^2$. The thin film processed by evaporation of the mixed powders of Sb and Te as an evaporation source showed a power factor of $0.12{\times}10^{-4}W/m-K^2$. The thin film fabricated by coevaporation of Sb and Te dual evaporation sources possessed a power factor of $0.73{\times}10^{-4}W/m-K^2$. With a reduction annealing at $300^{\circ}C$ for 2 hrs, the power factors of the films evaporated by using the $Sb_2Te_3$ ingot-crushed powders and coevaporated with Sb and Te dual evaporation sources were remarkably improved to $24.1{\times}10^{-4}W/m-K^2$ and $40.2{\times}10^{-4}W/m-K^2$, respectively.