• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.221-229
• /
• 2011

Due to the increase of oil price and the environmental issue such as the emission of volatile organic compounds, the necessity for developing alternative resins of petroleum-based adhesive resins, which have extensively been used for the manufacture of wood-based products, has been speculation since the early 1990. In our study, rapeseed flour (RSF), which is the by-product of bio-diesel produced from rapeseed, were hydrolyzed by enzymes. As a crosslinking agents of the RSF hydrolyzates, phenol-formaldehyde prepolymers (PF) were prepared. The RSF hydrolyzates and PF were mixed to complete the formulation of RSF-based adhesive resins, and the resins were applied to make the laminated veneer lumber (LVL). The physical and mechanical properties of the LVL were measured to examine whether RSF can be used as raw materials of adhesive resins for the fabrication of LVL or not. The average moisture content and soaking delamination rate of the LVL bonded with RSF-based adhesive resins exceeded the minimum requirement of KS standard. Moreover, thermal analysis of the RSF-based resins showed similar tendencies except for the RSF-based adhesive resins formulated with pectinase-hydrolyzed RSF. The bending strengths of the LVL were higher than that of the LVL made with commercial PF resins. These results showed the potential of RSF as a raw material of alternative adhesives for the production of LVL. Further works on the optimal conditions of RSF hydrolysis and spreading characteristics for RSF-based adhesive resins is required to improve the adhesive performance of RSF-based resins.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.197-205
• /
• 2011

Cellulose nanofibrils (CNF) with 50~100 nm diameter were manufactured from micro-size cellulose by an application of a high-pressure homogenizer at 1,400 bar. High strength nanopapers were prepared over a filter paper by a vacuum filtration from CNF suspension. After reinforcing and dispersing CNF suspension, hydroxypropyl cellulose (HPC) and polyvinyl alcohol (PVA)-based composites were tailored by solvent- and film-casting methods, respectively. After 2, 4, 6 and 8 passes through high-pressure homogenizer, the tensile strength of the nanopapers were extremely high and increased linearly depending upon the pass number. Chemical modification of 1H, 1H, 2H, 2H-perfluorodecyl-triethoxysilane (PFDTES) on the nanopapers significantly increased the mechanical strength and water repellency. The reinforcement of 1, 3, and 5 wt% CNF to HPC and PVA resins also improved the mechanical properties of the both composites.

• Journal of Mushroom
• /
• v.18 no.1
• /
• pp.95-99
• /
• 2020

The trade deficit in mushrooms has continued to increase in recent years. This study explored major issues and challenges faced by the mushroom industry to increase export, and to prioritize the current issues and challenges based on their relative importance. 11 major issues and challenges in the mushroom industry were highlighted in focus group interviews. Best-worst scaling analysis prioritized these major issues and challenges, and questionnaire surveys were completed by 31 mushroom industry experts. The results revealed that strengthening the mushroom quality and price competitiveness were the main priorities, followed sequentially by a diversification of the overseas export markets and stabilization of the domestic mushroom price.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.86-89
• /
• 2011

Purpose: The KOTRON-13 cyclotron was developed in South Korea and was introduced to regional cyclotron centers to produce short-lifetime medical radioisotopes. However, this cyclotron has limited capacity to produce carbon-11 isotope so far. We herein study how to develop and optimize an effective carbon-11 target system in the KOTRON-13 cyclotron by changing cooling system, combing with fluorine-18 target and evaluating beam currents. Materials and Method: To develop the optimal carbon-11 target and an effective cooling system, we designed the carbon-11 target system by Stopping and Range of Ions in Matter (SRIM) simulation program and considered the cavity pressure during irradiation at target grid. In this investigation, we evaluated the yield of carbon-11 production at different beam currents and the stability of the operation of the KOTRON-13 cyclotron. Results: The production of carbon-11 was enhanced from about 1.700 mCi ($50{\mu}A$) to 2,000 mCi ($60{\mu}A$) on the carbon-11 target which developed by seoul national university bundang hospital (SNUBH) and Samyoung Unitech. Additionally, the cooling condition was showed stable to produce carbon-11 under high beam current. Conclude: The carbon-11 target system of the KOTRON-13 cyclotron was successfully developed and improved carbon-11 production. Consequently, the operation of carbon-11 target system was highly effective and stable compare with other commercial cyclotrons. Our results are believed that this optimal carbon-11 target system will be helpful for the routine carbon-11 production in the KOTRON-13 cyclotron.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.98-102
• /
• 2009

Various physical properties of soils were investigated in the areas where organic farming had been practiced widely, for upland fields. The investigations were also conducted in the nearby fields under conventional to find out the influence of organic farming on the physical properties of soils. The investigated properties involved bulk density, hardness, shearing resistance, friction resistance, sinking depth of small rectangular board, water stable aggregates and the depth of soil available to plants. By and large, the practice of organic farming tended to improve all of the physical properties soils, investigated in upland soils. However, in case of water stable soil aggregates in upland soils, the reverse was previous data; in those soils water stable soil aggregates were less under organic farming. It was suspected that this might be due to intensive application of the organic materials with high C/N ratio like wood chips and wood bark. The contents of OM, Av. P2O5, and Ex. cations were higher in organic farming than those of nearby fields under conventional, due to heavy organic matter application. From the results, It could be concluded that soils under organic farming were looser and softer than those under conventional as shown by lower bulk density and hardness, but that the effect of organic farming on water stable aggregates were low.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.528-537
• /
• 2015

To reuse the waste bone from restaurants or butcher houses, the possibility of using waste bone powder after cooking as a filler for wood adhesives used in manufacturing plywood was investigated. Radiata pine (Pinus radiata D. Don) plywoods were manufactured by using commonly used wood adhesives such as urea-melamine formaldehyde (UMF) resin, urea-formaldehyde (UF) resin, and phenol-formaldehyde (PF) resin and the prepared fillers from cattle bone powder, pig bone powder, and seashell powder. Plywood fabricated by using cattle bone powder, pig bone powder, and seashell powder showed weaker performance in dry and wet glue-joint shear strength and wood failure than those of the plywood with wheat flour. The result showed that it was hard to use only bone powder for the replacement of wheat flour. However, the filler mixed with wheat flour and bone powders showed equivalent dry bonding strength and better water resistance than the wheat flour, indicating that bone powders mixed with wheat flour might be used for the manufacture of plywood. When bone powders were mixed with wheat flour as adhesive fillers the shell powder showed the lowest bonding properties and there was no big difference between the cattle bone powder and the pig bone powder.

• Land and Housing Review
• /
• v.3 no.4
• /
• pp.357-367
• /
• 2012

The efficient business scheme were suggested with the consideration of the local development condition at Ulaanbaatar. Major findings of the study were presented as follows. First, high level of education and the underground resources are presented as the merits of Mongolia. On the other side, the defects are limited domestic demands of 2.6 millions of population and the insufficiency of the infrastructure. The improvement of the infrastructures like roads, water & sewage, electric power, and heating is urgent while the development pressure of Ulaanbaatar is expected to be high due to the continuous inflow of population. Secondly, the Mongolian land system consists of the right of ownership, lease and use, therefore there are some differences among the right of land. Thirdly, definite business scheme to sell land in lots and to sell buildings in lots are suggested which are actual methods to participate in the development project in Ulaanbaatar. Moreover, enhancing the possibility to sell the lands, fixing the proper sale price to secure the profit, finding the proper buyer for the profitable lands, investing of quota and guaranteeing of granting the principal and interest by the Mongolian government, etc. are presented as consideration when participate in projects.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.2
• /
• pp.145-156
• /
• 2020

The climate change occurring all over the world increases the risk, specially in urban area, Accordingly, rainwater pumping station expansion is required than before. In order to increase the efficiency of the rainwater pumping station, the analysis of flow characteristics in the pump sump is needed for vortex control. Many efforts have been made to illuminate the vortex behavior using PIV, but any reliable results have not been obtained yet, because of the limitations in image capturing and dependency of measured velocity values on the interrogation area and time interval used for velocity calculation. In this study, therefore, experiments were carried out to find out the limitation of PIV and estimate the validation of the velocity values associated with the analysis parameters such as interrogation area, time interval, grid size. For the experimental condition used in this study, the limitation of PIV and the effects of parameters on the velocity estimation are presented.

• Journal of the Mineralogical Society of Korea
• /
• v.25 no.2
• /
• pp.63-76
• /
• 2012

Tachylite, black basaltic glass formed by the rapid cooling of molten basalt, locally occurs at the Basaltic Agglomerate Formation (BAF), the lowest formation of Ulleung Island. The purposes of this study are to characterize the occurrence and mineralogy of tachylite and to elucidate its formation condition, with emphasis on its fracture pattern, which can serve as implications for the early volcanic activity of Ulleung Island. To this end, we investigated the occurrence pattern of tachylite in the field and carried out mineralogical analyses using optical microscope, XRD, EPMA, and SEM. Tachylite occurs at the chilled margin of basic dikes which are distributed in Naesujeon, Dodong and Jeodong seasides, Turtle Rock, and Yaerimwon, whose widths vary from several cm to 10 cm. It is evident that the outer surface of tachylite is dense and smooth, whereas the inner surface, if fractured, is characterized by conchoidal fracture. The matrix of tachylite consists of amorphous, glass and some fine-grained phenocrysts present in tachylite include biotite, anorthoclase, sanidine, plagioclase, hornblende, and Fe-Ti oxides. The fracture patterns characteristic of tachylite are subrounded, oval, or less commonly polygonal, bounded by joints to form globule or lump. Taking into account texture and mineralogy, tachylite is interpreted to have undergone little subsequent alteration at low temperature via hydration or hydrolysis that could form clay minerals after it was formed. Because tachylite with peculiar fractures occurs as dikes in a close association with BAF, its presence is considered as reliable evidence that when tachylite formed, the most part of BAF was still under subaqueous conditions, or at least saturated with seawater.

• Journal of Animal Science and Technology
• /
• v.51 no.2
• /
• pp.105-110
• /
• 2009

The Objective of this study was to compare performances of proven and young holstein bulls bred in Korea. Proven bulls are categorized into the imported and the korean ones. Data from 148,329 heads of daughters of 1,128 bulls from 1990 to 2004 were used in this study. Proven bulls showed higher milk yield than young bulls in same year. Young bulls, however, always yielded more milk than korean bulls when proven bulls were categorized into the imported and the korean ones. Hence, it was proven that dairy bull selection program had properly been functioned in Korea. Selected bulls, which were korean proven bulls and young bulls, yielded higher milk fat than imported bulls as the selection was weighted on the yield of the milk fat. This comparison was based on the performances of daughters without the consideration of the semen price. Semen price of the imported proven bulls were higher than the korean proven bulls and the semen of young bulls was free. Hence, the performances of korean bulls with the consideration of the preferential effect would be much higher than others, and further studies are necessary.