• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3396-3402
• /
• 2014

The importance of shape design for strength is highly regarded when applied to thin plate products in Ceramic Injection Molding (CIM), such as cases for electronic goods. This study analyzed the characteristics of the mechanical strength of CIM product by measuring the flexural strength and elastic modulus through a 3-point bending test according to the thickness of a thin plate test piece prepared by CIM. The specimen with a thickness of 0.48mm required a 82.9~94.5N fracture load, whereas a 1.0mm thick test piece required 233.6~345.8N. The increase in thickness by 0.5mm resulted in a 3-fold increase in the fracture load, whereas the elastic modulus decreased by 20%. The thicker the specimen, the lower relative density and surface hardness of the specimen. This is because the thicker the specimen, the lower the powder fraction of the ceramic mixture, and the material properties partially change after sintering.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.9 s.240
• /
• pp.1235-1242
• /
• 2005

A district heating(DH) system supplies environmentally-friend heat and is appropriate for reduction of energy consumption and/or air pollutions. The DH transmission pipe, composed of supply and return pipes, has been used to transmit the heat and prevent heat loss during transportation. The two types of pipes are operated at a temperature of $75\~115^{\circ}C\;and\;40\~65^{\circ}C$, respectively, with an operating pressure of less than 1.568MPa. The objectives of this paper are to systematize data processing of transition temperature and investigate its effects on fatigue life of DH pipes. For the sake of this, about 5 millions temperature data were measured during one year at ten locations, and then available fatigue lift estimation schemes were examined and applied to quantify the specific thermal fatigue life of each pipe. As a result, a relational database management system as well as reliable fatigue lift evaluation procedures is established for Korean DH pipes. Also, since the prototypal evaluation results satisfied both cycle-based and stress-based fatigue criteria, those can be used as useful information in the future fer optimal design, operation and energy saving via setting of efficient condition and stabilization of water temperature.

• Informatization Policy
• /
• v.23 no.2
• /
• pp.35-53
• /
• 2016

This paper attempts to present critical issues of the information society and an alternative research addressing the challenges of ensuring that ICT is applied in ways that are enabling and responsive to social contexts in which people live their lives. Drawing the question of why insights arising from the mainstream vision are rarely useful in policies, the study highlights some developmental paradigms linked to ICT. It explores how ICT is seen as a means to development, and elaborates on the limitations of how current issues are related to the quality of life. The results indicate that ICT reduces quality of life while economic growth entails the opposite. The research framework here involves some meaningful components of cultural residues: independence, risk-taking, government responsibility by mapping how the level of ICT is distributed in the topology of values around the world. Moving to the next phase, ICT policy design and implementation need to be set up practically in a broad perspective that can be pursued by those concerned with social and technological innovation.

• Proceedings of the Korean Society of Organic Agriculture Conference
• /
• 2009.12a
• /
• pp.291-291
• /
• 2009

쌀 생산관리 방법에 따른 논 생태계의 생물다양성을 조사하기 위하여 관행, 우렁이, 투구새우, 심수관개, 오리농법 등으로 구분하여 벼 재배기간 동안 수서생물종과 식물종을 조사하였다. 논물과 토양에 서식하는 생물종을 쿼드라트법을 활용하여 조사한 결과, 토양생물의 풍부도는 이앙기는 관행농법, 분얼기에는 투구새우 농법이 높았으며, 출수기에는 무논, 쌀겨 농법에서 가장 많은 토양생물이 서식하고 있었다. 또한, 줄 채집에 의한 수서생물 종은 분얼기와 출수기, 육상생물은 수확기때 풍부하였으며 관행농법은 분얼기에 가장 출현종이 많았던 반면 오리농법은 전 조사기간 동안 가장 개체수가 적었으며 무논+쌀겨농법이 생물다양성 기여도가 가장 높았다. 생물조사 결과 관행보다는 유기재배논에서 종 풍부도가 2배이상 높게 나타났으며, 쌀겨농법은 이앙기~분얼기까지는 쌀겨 분해에 따른 유기산에 의해 수서곤충이 급감되나 분얼기이후 개체수가 회복되어 무논+쌀겨구에서 가장 높았다. 전 조사지점 논둑의 식물 분포는 농법별 유의성이 없었으며 논둑의 우점식물은 쑥, 개망초,질경이, 클로버, 미나리, 미국가막사리, 쇠뜨기, 둑새풀, 미나리 등이었다. 출수기를 전후하여 관행논과 유기논, 그리고 둠벙의 유무로 구분하여 생물종을 조사한 결과, 먼저 관행논과 유기논에서 서식하는 생물종은 비슷하지만 수서생물의 개체수는 유기논이 관행논보다 43-54%나 많았다. 한편, 둠벙의 유무에 의한 생물조사에서는 둠벙이 있는 논이 없는 논보다 서식종이 35-47%정도 높은 경향을 나타내어 생물다양성을 증진하기위해서는 낙수기때 수서생물들의 피난처를 확보하여 주는 소규모 둠벙이 효과적인 것으로 판단되었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.295-302
• /
• 2013

The two cross-roll straightening process at room temperature is a manufacturing method for improving the straightness of a drawn wire. The distribution and magnitude of the internal and surface residual stresses of the drawn wire are changed after the wire-drawing process through the two cross-rolls; this also results in a change in the diameter of the drawn wire. The remaining residual stresses of the drawn wire after the wire-drawing dimensional changes were analyzed according to the distance between the rolls, oblique angle between the axes of the roll and the wire, predicted residual stresses, and dimensional change in the final product. The oblique angle between the concave and convex rolls did not affect the residual stresses or dimensional change, but the distance between rolls did.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1239-1249
• /
• 2013

In this study we establish a process to predict hardening behavior considering the Bauschinger effect for zircaloy-4 sheets. When a metal is compressed after tension in forming, the yield strength decreases. For this reason, the Bauschinger effect should be considered in FE simulations of spring-back. We suggested a suitable specimen size and a method for determining the optimum tightening torque for simple shear tests. Shear stress-strain curves are obtained for five materials. We developed a method to convert the shear load-displacement curve to the effective stress-strain curve with FEA. We simulated the simple shear forward/reverse test using the combined isotropic/kinematic hardening model. We also investigated the change of the load-displacement curve by varying the hardening coefficients. We determined the hardening coefficients so that they follow the hardening behavior of zircaloy-4 in experiments.

• Journal of Sensor Science and Technology
• /
• v.9 no.5
• /
• pp.380-388
• /
• 2000

The finite element analysis of a micro turbine was made to investigate safety margin of its operating condition for the high aspect ratio nickel micro turbine blades fabricated by conventional LIGA-like method. From our study, we found that the fabricated turbine could not exceed its yield strength even if the pressure difference between inlet and outlet of turbine blade was about 44kPa, and the correlation of friction coefficient and the maximum stress, caused by contact friction between outer diameter of shaft and inner diameter of turbine blade, was somewhat reciprocal. The maximum stress was decreased with the increasing contact friction, when turbine blade was in its state of rotation. By the results of our study, we conclude that it is possible to fabricate metal micro turbine more easily han surface micromachining technology and to operate with no risk of metal structure's damage, which is caused by yield strength, if the operating condition with the design of micro turbine itself are optimized. It is useful to adopt other applications which have the contact problems between a moving part and the fixed one in micro structures.

• The Journal of the Korea Contents Association
• /
• v.12 no.6
• /
• pp.424-437
• /
• 2012

As to the increase of crime against children, the importance of safety in school area is more emphasized ever. Safety in school area can be achieved by the well-organized combination of physical, managemental and spatial planning factors. The purpose of this paper is to investigate the spatial planning direction to prevent crimes for the schools and their surroundings on the viewpoint of CPTED(crime prevention through environmental design). Field survey using checklist drawn up with 5 major CPTED principles was conducted for 7 schools(primary, middle and high schools) located at Noen New-town, Daejeon Korea. Problems derived from field survey were categorized to 5 CPTED principles and countermeasures were suggested together with computer graphic simulation. CPTED design principles and guidelines for spatial planning can make school area safer because these can assure natural surveillance, territoriality, natural access control, etc.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.2 no.1
• /
• pp.54-64
• /
• 1984

This paper is a study on structural measurement by using a terrestrial camera. The aim of this paper is to understand the method of a composition by analyzing the geometrical compositive ratio of threestoried pagodas at Gamun-Sa, Gosun-Sa, Bulguk-Sa, Seated iron Buddha in Kwang-Jn, and Main-Seat Buddha at Sukkuram Cave-temple. Measured data and contour maps are accurately obtained by means of photogrammetry, and the following points are able to he found by analyzing them. At first, for Stone Pagodas. the breaths of the Okgesuks are made to the ratio, 8 : 7 : 6. And when an equililateral triangle and an 45$^{\circ}$ isosceles triangle are drawn of which the bases are the length of the upper Gabsuk, and then a circle is drawn whose radius is the length between the vertexes of the two triangles and its center is the vertex of the former the circle passes the upper line of the third Oksin. Also it can be found that an $70^{\circ}$ isosceles triangle being drawn at base line, the triangle passes the edge point of the upper Gabsuk and the center of the third Okgesuk. Also for Budha statues, it can be found that circles whose center is that of eyes can be drawn, and if 2 lines which pass the shoulder and the center of Buddha's body are extended, they intersect the knees.