• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.31-37
• /
• 2017

Recently, there has been substantial interest in flexible and wearable devices whose properties and performances are close to conventional devices on hard substrates. Despite the advancement on flexible devices with organic semiconductors or carbon nanotube films, their performances are limited by the carrier scattering at the molecular to molecular or nanotube-to-nanotube junctions. Here in this study, we demonstrate on the vertical semiconductor crystal array embedded in flexible polymer matrix. Such structures can relieve the strain effectively, thereby accommodating large flexural deformation. To achieve such structure, we first established a low-temperature solution-phase synthesis of single crystalline 3D architectures consisting of epitaxially grown ZnO constituent crystals by position and growth direction controlled growth strategy. The ZnO vertical crystal array was integrated into a piece of polydimethylsiloxane (PDMS) substrate, which was then mechanically detached from the hard substrate to achieve the freestanding ZnO-polymer composite. In addition, the characteristics of transferred ZnO were confirmed by additional structural and photoluminescent measurements. The ZnO vertical crystal array embedded in PDMS was further employed as pressure sensor that exhibited an active response to the external pressure, by piezoelectric effect of ZnO crystal.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.348-350
• /
• 2006

In this paper, we design a new controller for an ultra-precision positioning system. In general, time optimal control enables to reach a target position faster than others. However it shows a weakness to chattering effect. In order to solve the problem, a new control algorithm based on sliding mode control is proposed. The suggested controller is composed of LQR control and sliding mode control. By performing some simulations, we prove that the proposed controller is more robust than time optimal control under the circumstance of parameter uncertainties and external disturbances.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.4
• /
• pp.271-275
• /
• 2016

For machining systems like the motor driven linear stage which have high precision positioning with a long stroke, it is necessary to examine the repeatability of the reference position decision. Though piezo (PZT) actuator driven linear stages have high precision feed drivers and a short stroke, they have some limitations for reference position decisions if they have not been equipped with an accurate home sensor. This study was performed to examine the repeatability for home position decision of a EE-SX671 photo sensor as a home switch by using piezo actuator driven linear stages and capacitance probe.

• Journal of the Korean Vacuum Society
• /
• v.16 no.1
• /
• pp.7-14
• /
• 2007

A new horizontal neutron reflectometer has been designed and now under construction at the HANARO, 30 MW research reactor, in Daejon, Korea. We performed simulations of neutron ray-tracing to evaluate the performance of all of the optical components of the instrument with a Monte Carlo technique using McStas. The feasible wavelength of the incident neutron beam is $2.5{\AA}$. It produces a q-range up to $0.126{\AA}^{-1}$ with a supermirror as a deflector. Our studies showed improvement of the performance of the guide tube and monochromators. Although the performance is limited in q-range, it promises to be the first reflectometer in Korea for the study of free surfaces, which is currently in demand.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.3
• /
• pp.47-55
• /
• 2013

Curved duct channel flow characteristics for non-Newtonian gel fluid is investigated. A simulant gel propellant mixed by Water, Carbopol 941 and NaOH solution has been chosen to analyze the gel propellant flow behavior. Rheological data have been measured prior to the flow analysis where water-gel propellant and water-gel propellant with $Al_2O_3$ nano particles are both used. The critical Dean number examined by the numerical simulation in the U-shape duct flow reveals that although water-gel-nano propellants have higher apparent viscosity, the critical Dean number do show no notable difference for both the two gel propellant. It is found that the power-law index may be a dominant parameter in determining the critical Dean number and that the gel with particles addition may be more vulnerable to Dean instability.

• Journal of the Mineralogical Society of Korea
• /
• v.32 no.3
• /
• pp.151-162
• /
• 2019

Todorokite, a tunnel-structured manganese oxide, can contain cations within the relatively large nanopores created by the $3{\times}3$ Mn octahedra. Because todorokite is poorly crystalline and found as aggregates mixed with other phases of Mn oxides in nature, the coordination structure of cations in the nanopores is challenging to fully characterize in experiment. In the current article, we report the atomistic coordination structures of $Mg^{2+}$ ions in todorokite tunnel nanopores using the classical molecular dynamics (MD) simulations. In experiment, $Mg^{2+}$ is known to occupy the center of the nanopores. In our MD simulations, 60 % of $Mg^{2+}$ ions were located at the center of the nanopores; 40 % of the ions were found at the corners. All $Mg^{2+}$ located at the center formed the six-fold coordination with water molecules, just as the ion in bulk aqueous solution. $Mg^{2+}$ ions at the corners also formed the six-fold coordination with not only water molecules but also Mn octahedral surface oxygens. The mean squared displacements were calculated to examine the dynamic features of $Mg^{2+}$ ions in the one-dimensional (1D) nanopores. Our MD simulations indicate that the dynamic features of water molecules and the cations observed in bulk aqueous solution are lost in the 1D nanopores of todorokite.

• Korean Journal of Crystallography
• /
• v.14 no.2
• /
• pp.79-83
• /
• 2003

The microstructure of bulk electrolytic MnO₂ (EMD) was studied using x-ray diffraction and transmission electron microscopy (TEM). The bulk sample showed a typical powder x-ray diffraction pattern of EMD materials. TEM study showed that the structure of EMD is present at two length scales;grains, ∼0.2 ㎛ in diameter, and ∼10 nm crystallites within the grain. The electron beam microdiffraction study revealed that each grain is an assemblage of multiphase with a common crystallographic orientation, and_that ∼50% of the crystallites are Ramsdellite, ∼30% are ε-MnO₂, and ∼15% are Pyrolusite. The ｛1120｝peak located at about 67° in powder XRD pattern as well as a high-resolution electron microscope (HREM) image of (0001) plane support the existence of ε-MnO₂ phase.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.117-124
• /
• 2004

Recently, nano-methodology is increasingly important as the ruler for measuring nano-technology, and we applied the linear encoder to nano-methodology. The quadrature output in the linear encoder has an effect on increasing the resolution in some techniques. Already, various interpolation techniques based on the quadrature signal have applied to the precision servo system. In this paper, we propose a new interpolation algorithm for ultra-precision positioning in the low speed with simulation by MATLAB SIMULINK. This method modified previous methods and was properly designed for some given control system. To verify, we first fulfilled the encoder signal test to find main parameters fer the signal transformation, then we proved the proposed interpolation algorithm by experiments, which show that the result of the interpolation algorithm corresponds with the measurement of the laser interferometer in 100 nm unit approximately. In addition, we can get more precise measurement by more accurate and noise-free signal. So we need to compensate imperfections in the encoder signal. After that, we will apply this algorithm to nano positioning system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.5
• /
• pp.468-474
• /
• 2012

In this study, experimental studies were performed for the carbon nanomaterial(CNM) which is catching on as a material for eco-ship. The opposed-flow methane flame was used as a heat source for synthesis of CNM. Ferrocene was used as a catalyst for the synthesis of CNM. These major parameters were $H_2$ mixing rate and sampling positions that synthesize CNMs in opposed-flow diffusion flames. The propensities of CNMs were experimentally determined using SEM and TEM images. The experimental result showed that the amount of CNTs was increased with increasing $H_2$ concentration. It can also be found that the optimal temperature in opposed-flow methane flame for synthesis of CNT was about 1500 K.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.1 s.178
• /
• pp.129-135
• /
• 2006

In this study, a two-axis ultra-precision stage driven by piezoelectric elements is presented. The stage has a flexure-type parallel linear guide mechanism consisting of quad-symmetric simple parallel linear springs and quad-symmetric double compound linear springs. While the simple parallel linear springs guide the linear motion of a moving plate in the stage, the double compound linear springs follow the motion of the simple parallel linear spring as well as compensate the parasitic motions caused by the simple parallel linear springs. The linear springs are designed by rectangular beam type flexures that are deformed by bending deflection rather than axial extension, because the axial extension is smaller than the bending deflection at the same force. The designed guide mechanism is analyzed by finite element method(FEM). Then two-axis parallel linear stage is implemented by the linear guide mechanism combined with piezoelectric elements and capacitance type displacement sensors. It is shown that the manufactured ultra-precision stage achieves 3 nm of resolution in x- and y-axis within 30 ${\mu}m$ of operating range.