• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.233-242
• /
• 2023

In this paper, the effect of mass injection on the control of tip vortex cavitation was studied experimentally. A mass injection system for a 3D hydrofoil was designed to control the location of injection as well as the injection rate. A series of cavitation tests were carried out in a cavitation tunnel for different injection locations and rates. The cavitation behaviour was observed using a high-speed camera and the corresponding noise was measured using a hydrophone installed in the observation window. The results showed that the tip vortex cavitation was suppressed under certain conditions and the noise was reduced in some frequency bands. It was also found that there is a location where the effect of mass injection could be maximized and hence the noise reduction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.12
• /
• pp.1410-1416
• /
• 2009

In this paper, the purpose is to investigate the stability and variation of natural frequency of a cracked cantilever beams subjected to follower force and tip mass. In addition, an analysis of the flutter instability(flutter critical follower force) of a cracked cantilever beam as slenderness ratio and crack severity is investigated. The governing differential equations of a Timoshenko beam subjected to an end tangential follower force is derived via Hamilton's principle. The two coupled governing differential equations are reduced to one fourth order ordinary differential equation in terms of the flexural displacement. Finally, the influence of the slenderness ratio and crack severity on the critical follower force, stability and the natural frequency of a beam are investigated.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.6
• /
• pp.99-107
• /
• 2008

In this paper, the stability of a cracked cantilever Timoshenko beam with a tip mass subjected to follower force is investigated. In addition, an analysis of the flutter instability(flutter critical follower force) and a critical natural frequency of a cracked cantilever Euler / Timoshenko beam with a tip mass subjected to a follower force is presented. The vibration analysis on such cracked beam is conducted to identify the critical follower force for flutter instability based on the variation of the first two resonant frequencies of the beam. Therefore, the effect of the crack's intensity, location and a tip mass on the flutter follower force is studied. The crack section is represented by a local flexibility matrix connecting two undamaged beam segments. The crack is assumed to be in the first mode of fracture and to be always opened during the vibrations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.4
• /
• pp.317-323
• /
• 2014

This study is concerned with the free vibration analysis of an inextensible uniform rope with a spring-mass system at the tip. The rope is hanged vertically in a gravitational field. This problem is related to the free vibration of an elevator rope connected to an elevator cage. The equation of motion and the corresponding boundary conditions are derived by using the Hamilton's principle. The general solution of the governing equation of motion is expressed in terms of Bessel functions. The characteristic equation was derived by applying the boundary conditions. The characteristic values which are in fact non-dimensionalized natural frequencies were obtained numerically. The effects of mass and spring constant were investigated. The numerical results show how the tip mass and spring affect the natural frequencies of the rope.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.12
• /
• pp.822-829
• /
• 2015

A transfer matrix method has been developed to determine the more accurate natural frequencies for the bending vibration of Bernoulli-Euler beam with linearly reduced width and a concentrated tip mass. The proposed method can be computed an infinite number of the natural frequencies using a single element. Using the differential equation, shear force, and bending moment in which can be deduced by the diverse variational principles, a transfer matrix is formulated. The roots of the differential equation are computed by the Frobenius method. The effect of the concentrated mass for the natural frequencies of width-tapered beams is examined through a parametric study, and to show the accuracy of the proposed method, the computed results compared with those obtained from commercial finite element analysis program(ANSYS).

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.2
• /
• pp.156-162
• /
• 1995

A numerical method for a 2-D oil boom model considering the flexibility of skirt has been developed The neater is assumed rigid and the skirt is tensioned membrane having a point mass at its end The fluid motion is potential. The kinematic condition which demands the continuity of the displacement is imposed at the joint between the floater and the skirt. The dynamic condition for the point mass is imposed at the bottom end of the skirt. The numerical method is based on the Green's function method in the frame of linear potential theory. It finds it's solution simultaneously from the total system of three equations, integral equation, the equation of motion of the floater and the equilibrium equation of the deformation of the skirt. Integral equation is derived by applying the Green's theorem to radiation potential and Green's function. Proper descretization of those three equations leads to the system of a linear algebraic equation. Due to the flexibility of skirt the motion of floater can be diminished in some range of wave frequency and furthermore the mechanism of resonance of the oil boom can be changed. The motion responses of various oil booms have been compared varying the length of the skirt and the point mass. The numerical method has been validated indirectly from the good correspondence between the motion responses of the flexible skirt model and the rigid skirt model in low frequency limit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.95-101
• /
• 2014

In this study, an ISM (immersed solid method) was used for investigating the mass flow rate and efficiency of an involute-gear pump featuring very high rotational speed. For considering circulation flow at the gear pump and housing, fluid flow was assumed as turbulent, and the rotational speed of the gear pump increased under the condition of constant pressure at both the inlet and outlet. The efficiency and mass flow rate of the gear pump were studied by varying its rotational speed and the clearance between the gear tip and the housing. In the simulation results, as the rotational speed were increased, the average mass flow rate and efficiency increased. Furthermore, as the clearance between the gear tip and the housing was increased, the average mass flow rate and efficiency decreased. The efficiency was 85.11, 90.94, and 93.62 at rotational speeds of 6,000 rpm, 8,000 rpm, and 10,000 rpm, respectively, under the condition that there was no clearance. In addition, the efficiency was 93.62, 93.29, and 92.74 at clearances of 0 m, 0.00001 m, and 0.00003 m respectively.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.216-225
• /
• 2017

제조 기술의 고도화가 이루어진 현 시점에서, 제품의 설계방식도 단순구조설계가 아닌 최적설계를 통해 제품의 경제성과 안정성을 동시에 획득하고 있다. 본 논문에서는 인장, 압축, 비틀림과 같은 다양한 힘을 받는 자전거의 크랭크 암에 대해 최적 설계를 진행하였고, EDISON의 Plastic Deformation with Damage Mechanism Analysis SW 프로그램을 통해 유한 요소 해석을 수행했다. 해석은 크랭크암 내부에 응력 값이 가장 높은 $90^{\circ}$를 경계조건으로 표면 응력을 고려한 구조, 내부 응력을 고려한 구조, 트러스를 적용한 구조와 MATLAB을 통해 위상최적화 후 추가적으로 형상을 최적화한 구조를 설계했다. 끝으로 경제성과 안정성을 판단하는 기준으로 각각의 질량 대비 강성을 확인하여 최적의 형상을 제시하였다.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.171-187
• /
• 2007

The purpose of this study is to measure the lathe tool vibration and verify its usefulness using the fiber optic interferometeric sensor instead of using common accelerometer. To compare two vibration signals a Fabry-Perot fiber optic sensor(FOS) is directly attached to the left-side surface of the lathe tool and an accelerometer is attached near to the fiber optic sensor. Measurement signals from the FOS and theoretical results of receptance simulation are compared. When the amplitude of tool vibration increased the frequency shift phenomena was occurred. This means that mass effect occurred and vibration spectrum moved to the low frequency region. Generally this results is agreement to the regenerative chatter. The chatter frequency is not same as the natural frequency of the tool itself. The FOS can also applied to laboratory experiments for students. This experimental technique is perhaps the first attempts because of directly attachment technique. Therefore, suggested Fabry-Perot fiber optic sensor can be used to monitoring the tool wear and vibration.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.825-835
• /
• 2017

This paper aims to build a drone platform based on an optimum design of its single arm. Its single arm is assumed as a cantilevered beam with a tip mass. Based on the numerical optimization theory, validation and optimization of a new design is conducted by comparing the results with the similar ones obtained by ANSYS. Finally, this design is reflected in the control simulation, and the requirement of an optimum structural design considering the resonance situation is satisfied.