• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.14-20
• /
• 2006

The discharge characteristics for the reset period of sustain pulses of display discharge in address overlapped display driving methode is studied. It has been understood that the display discharge is strongly influenced of not only the wall charge but also the space charge from the experiment result. The first display discharge which comes out exactly after the rest periods strongly depends on the width of the reset period and as for the second display discharge, the dependancy of it is very low. Even if the first display discharge is a little insufficient if the wall charge is accumulated enough, the second display discharge can be stably induced. However, considering the influence of the space charge, it is preferable within the width of $30[{\mu}s}]$ of the reset period. When the rest period is up to $30[{\mu}s}]$, the uniform voltage operation margin of the display discharge of about 12[V] was obtained.

• Elastomers and Composites
• /
• v.47 no.4
• /
• pp.341-346
• /
• 2012

Injection molding is one of the widely used polymer processing operations. It is being used for not only conventional injection molding but gas injection molding, water injection molding, and injection compression molding. Injection compression molding involves injection and compression operation, and it gives uniform physical property and high dimensional quality of product. In this study, injection compression characteristics for various product shapes have been investigated by computer simulation. Product containing side wall showed not much effective in injection compression molding since wall thickness direction was perpendicular to the compression direction. Uniform and low shrinkage was observed in injection compression molding comparing conventional injection molding. Subsequently injection compression molding can be used for molding precise product. Optimal injection compression molding condition was obtained using design of experiment for plastic lens and the results were compared with conventional injection molding.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.3
• /
• pp.157-164
• /
• 2008

While developing physical prototype from CAD model, rapid prototyping mainly focuses on two key points reducing time and material consumption. So, we have to change from a traditional solid model to building a hollowed prototype. In this paper, a new method is presented to hollow out solid objects with uniform wall thickness to increase RP efficiency. To achieve uniform wall thickness, it is necessary to generate internal contour by slicing the offset model of an STL model. Due to many difficulties in this method, this paper proposes a new algorithm that computes internal contours computing offset model which is generated from external contour using wall thickness. Proposed method can easily compute the internal contour by slicing the offset surface defined by the sum of circle swept volumes of external contours without actual offset and the circle wept volumes. Internal contour existences are confirmed by using the external point. Presented algorithm uses the 2D geometric algorithm allowing RP implementation more efficient. Various examples have been tested with implementation of the algorithm, and some examples are presented for illustration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.72-72
• /
• 2010

탄소나노튜브(carbon nanotubes : CNTs)는 뛰어난 전기적, 물리적인 특성을 가지고 있기 때문에 다양한 분야에서 이를 활용하려는 노력들이 활발히 이루어지고 있다. CNTs의 전기적인 특성은 직경에 의해 결정되므로, 직경을 균일하게 제어하는 일이 CNTs를 기반으로 한 전자소자 응용에 가장 중요한 사항이라 할 수 있다. 일반적으로 화학기상증착법(chemical vapor deposition, CVD)으로 합성된 CNTs의 직경은 촉매의 크기에 의존하기 때문에, 촉매의 크기를 제어하기 위한 다양한 연구들이 활발히 진행되고 있다[1-3]. 하지만 CNTs의 성장온도 근처에서 촉매 입자는 표면 확산(surface diffusion)에 의해 응집(agglomeration)되기 때문에 작고 균일한 크기의 촉매를 얻기 어렵다. 본 연구에서는 Si(001) 기판 위에 지지층(supporting layer)인 Al의 두께를 변화시켜 증착하고, 열적산화과정을 통해 $Al_2O_3$ 층을 형성한 후 Fe을 증착하여 CNTs를 합성하였다. $Al_2O_3$ 지지층과 Fe 촉매입자의 구조와 화학적 상태를 원자힘현미경 (atomic force microscopy, AFM), 주사전자현미경 (scanning electron microscopy, SEM), 투과전자현미경 (transmission electron microscopy, TEM), X-선 광전자 분광기(X-ray photoelectron spectroscopy)를 통해 분석하였고, 성장된 CNTs는 SEM, TEM, 라만 분광법 (Raman spectroscopy)을 통해 분석하였다. 그 결과, $Al_2O_3$ 층은 두께에 따라 각기 다른 표면 거칠기(RMS roughness)와 결정립(grain)의 크기를 갖게 되며, 이러한 표면구조가 Fe 촉매입자의 표면확산에 의한 응집에 관여하여 CNTs의 직경에 영향을 미치는 것을 확인하였다. 또한 $Al_2O_3$ 지지층의 두께가 15 nm인 경우, Fe의 응집현상이 억제되어 좁은 직경분포를 지닌 고순도 단일벽 탄소나노튜브(Single-walled CNTs)가 성장되는 것을 확인하였다.

• Composites Research
• /
• v.23 no.2
• /
• pp.1-9
• /
• 2010

This study analyzes the apparent fracture toughness of a thick-walled cylinder with a functionally graded material (FGM) coating at the inner surface of the cylinder. The cylinder is assumed to have a single radial edge crack emanating from its inner surface. The crack surfaces and the inner surface of the cylinder are subjected to an internal pressure. The incompatible eigenstrain developed in the cylinder due to nonuniform coefficient of thermal expansion as a result of cooling from sintering temperature is taken into account. Based on a method of evaluating stress intensity factor introduced in our previous study, an approach is developed to calculate apparent fracture toughness. The approach is demonstrated for a cylinder with a TiC/$Al_{2}O_{3}$ FGM coating and some numerical results of apparent fracture toughness are presented graphically. The effects of material distribution profile, cylinder wall thickness, application temperature, and coating thickness on the apparent fracture toughness are investigated in details. It is found that all of these factors play an important role in controlling the apparent fracture toughness of the cylinder.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.2
• /
• pp.264-279
• /
• 1997

Background : To analyze the morphologic characteristics of low density lymph node in etiologic differentiation of lymphadenopathy, emphasizing the different features between tuberculosis and lung cancer, on contrast enhanced CT scan. Method : A total of 64 patients who showed low density lymph nodes on chest CT scan were analyzed. Primary causes were tuberculosis (n=28), lung cancer (n=27), malignant lymphoma (n=5) and metastasis from extrathoracic malignancies (n=4). CT scan was performed with 10mm slice thickness and 7 characteristic features were evaluated : location, size, presence or absence of the nonnecrotic lymph node, calcification, perinodal fat obliteration, thickness and evenness of the enhancing rim. Results : In patients with tuberculous lymphadenopathy, lymph nodes with uneven (68.0%) and thick (62.1%) enhancing rim were more common than lung cancer (p<0.05). Low density lymph nodes with less than 1 cm in size were found only in tuberculous lymphadenopathy(n=10). In 48.2% of patients with lung cancer, more than 1 nonnecrotic enlarged lymph node were coexisted, whereas 21.4% in patients with tuberculous lymphadenopathy(p=0.06). However, the size, location and calcification were not statistically significant between tuberculous lymphadenopathy and lung cancer. Conclusion : Tuberculous lymphadenopathy is strongly suggested when enhancing rim of enlarged lymph nodes is uneven and thick, when the coexisting nonnecrotic lymph nodes are few in number and when central low density is encountered in normal sized lymph nodes.

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.383-387
• /
• 2007

In this paper the design of the discharge cleaning system for KSTAR vacuum vessel is described. We first discuss about the parameters which are related the efficiency of discharge cleaning. The RG(RF-assisted Glow) discharge which has the ignition and sustain pressure lower than those in the case of DC discharge, thus has the higher efficiency of discharge cleaning. So we adopt the RG discharge, in practical design, for KSTAR discharge cleaning system. For uniformity of the cleaning effect, we plan to install two discharge cleaning systems in A- and I-port of the KSTAR vacuum vessel. The designed system will be adapted for the study of the fuel recycling and of the boronization as well as the discharge cleaning of the KSTAR vacuum vessel.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.4
• /
• pp.215-221
• /
• 2002

Epitaxial Si layers were deposited on (100) Si substrates by hot-wall chemical vapor deposition (CVD) technique using the $SiH_2Cl_2/H_2$chemistry. Thermochemical calculations of the Si-H-Cl system were carried out to predict the window of actual Si deposition process and to investigate the effects of process variables (i.e., deposition temperature, reactor pressure, and input gas molar ratio ($H_2/SiH_2Cl_2$)) on the epitaxial growth. The calculated results were in good agreement with the experiment. Optimum process conditions were found to be the deposition temperature of 850~$950^{\circ}C$, the reactor pressure of 2~5 Torr, and the input gas molar ratio ($H_2/SiH_2Cl_2$) of 30~70, providing device-quality epitaxial layers.

• Journal of Energy Engineering
• /
• v.28 no.3
• /
• pp.1-9
• /
• 2019

A major stress determining the remaining life of the tube in feedwater heater of fossil fuel power plant is hoop stress by the internal pressure. However, thermal stress due to temperature difference across the wall thickness also contributed to reduce the remaining life of the tube. Therefore, thermal loading must be considered even though the contribution of internal pressure loading to the stresses of the tube was known to be much higher than that of the thermal loading. In this study, thermal stress of the tubes in the de-superheating zone was estimated, which was generated due to the temperature difference across the tube thickness. Analytic equations were shown for determining the hoop stress and the radial stress of the tube with uniform thinning and for the temperature across the tube thickness. Accuracy and effectiveness of the analytic equations for the stresses were verified by comparing the results obtained by the analytic equations with those obtained from finite element analysis. Using finite element analysis, the stresses for eccentric thinning were also determined. The effect of heat transfer coefficient on thermal stress was investigated using series of finite element analyses with various values of heat transfer coefficient for both inner and outer surface of the tube. It was shown that the effect of heat transfer coefficient at outer surface was larger than that of heat transfer coefficient at inner surface on the thermal stress of the tube. Also, the hoop stress was larger than the radial stress for both cases of uniformly and eccentrically thinned tubes when the thermal loading was only considered without internal pressure loading.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.84-90
• /
• 2001

To investigate morphological characteristics of zephyr produced from two bamboo species, Phyllostachys nigra var. henonis and Gigantochloa apus, basic anatomic properties were examined by scanning electron microscopy and image analysis. According to SEM observation, zephyr from Phyllostachys nigra var. henonis was not of uniform in shape and showed macro crack between vascular bundle sheaths. This may be attributes to the sclerenchymatous fibers connected closely, thus resulting in difficult separation of intercellular layer. Zephyr from Gigantochloa apus was of uniform in shape, which may be caused by easy separation of intercellular layer of sclerenchymatous fibers having thin cell wall and large cell lumen. By image analysis in cross section of two species, the ratio of vascular bundle sheaths and cell wall ratio of sclerenchymatous fibers were examined. The ratio of vascular bundle sheaths in Phyllostachys nigra var. henonis was lower than that in Gigantochloa apus. However, cell wall ratio of sclerenchymatous fibers in Phyllostachys nigra var. henonis was higher than that in Gigantochloa apus.