• Korean Journal of Optics and Photonics
• /
• v.26 no.3
• /
• pp.168-171
• /
• 2015

The heat flow characteristics of a high-power optical semiconductor source have been analyzed using a 3D CFD commercial tool, and the thermal resistance values for each of the layers revealed the places for thermal bottlenecks to be improved. As the heat source of a LD (Laser Diode) has a small volume and a narrow surface, the effective thermal cross-sectional area near it is also quite small. It was possible to expand the cross-sectional area effectively by using graphene layers on the TIM (Thermal Interface Material) layers of a LD chip. The effective values of heat resistance for the layers are compared to confirm the improvement effect of the graphene layers before and after, which can be considered to expand the thermal cross section of the heat transfer path.

• Fire Science and Engineering
• /
• v.16 no.2
• /
• pp.1-7
• /
• 2002

In the normally, exit sign is always lighting on status by the connected to normal electrical source. So, there are happened to rise of the economical cost such as power consumption, maintenances and repair replacement of lamp etc. This paper are study on the new exit sign circuits by using high efficiency LED that is available for remote control and reduceible to power consumption, maintenance cost by the way of compensation fluorescent and incandescent lamps. As a results on the study, exit sign lamp is capable of control and supervisory in trigger angle by the remote control switch, widely and easily. And then, the response time was very fast in 600〔$\mu$s〕and also it can be find that the rising and fall time of oscillate circuit is maximum 200〔ns〕 as high sensitively. Finally, it obtain to the result that reducible of electrical power consumption and not required for replacement of lamp by using the high efficiency LED lighting source.

• Korean Journal of Optics and Photonics
• /
• v.30 no.5
• /
• pp.193-196
• /
• 2019

The design and control of thermal flow is important for the operation of high-power laser diodes (LDs). It is necessary to analyze and improve the thermal bottleneck near the active layer of an LD. As the error in prediction of the thermal resistance of an LD is large, typically due to the hyperbolic increase and saturation to linear increase of the thermal resistance as a function of thickness, it is helpful to use a simple, modified divergence model for the improvement and optimization of thermal resistance. The characteristics of LDs are described quite well, in that the values for simulated thermal resistance curves and the thermal cross section followed are almost the same as the values from the model function. Also, the thermal-cross-section curve obtained by differentiating the thermal resistance is good for identifying thermal bottlenecks intuitively, and is also fitted quite well by the model proposed for both a typical LD structure and an improved LD with thin capping and high thermal conductivity.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.10a
• /
• pp.317-319
• /
• 2015

기존 육지초인용으로 사용되는 전구식 회전형 대형등명기는 고압방전등을 사용하고 있어 고장발생 빈도가 높고 긴급수리에 장시간이 소요되어 기능 유지가 어려우며, 제품 가격이 높아 신규 설치 및 등명기 교체 시 비용 부담이 가중되는 문제점이 대두되고 있다. 따라서 기존 광원(메탈할라이드 램프 또는 텅스텐할로겐 램프)의 문제점을 개선하고, IALA에서 권고하는 규격을 만족하는 효율성과 안정성을 확보한 LED 대형등명기 개발이 국 내외에서 활발하게 수행되고 있다. 이러한 LED 대형등명기는 LED 모듈을 안정적으로 구동하는 LED 드라이버와 정확한 등질구현을 위한 모터제어회로가 필요하다. 또한 LED 모듈 및 LED 드라이버 고장 시 예비장치로 절환이 가능한 회로설계 및 교체유지관리가 용이한 제어반 기구개발 및 특성연구가 필요하다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1203-1209
• /
• 2010

LED lights as a newly-growing industry are highly energy-efficient and have drawn lots of attention due to higher illuminance and longer life compared to other light sources. In this study, MR16 lights with one high-power LED were considered for the replacement of the previous halogen lights or LED lamps with many LEDs. Thus, fundamental experiments of LED on a MCPCB, 3-dimensional numerical analysis for heatsink design and performance tests of the prototype lights have been done and the MR16 LED lights have been successfully developed.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.2
• /
• pp.36-40
• /
• 2018

Point LED applied in Korea is applied to communication RCLED, but it is designed to be suitable for communication, so it does not meet requirements in fiber coupling rate and optical output. - Currently, domestic optical pipe manufacturers use general LEDs for light emitting devices, but Japanese products use high power point LEDs to develop superior point LED (RED 620 ~ 660nm).

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.681-687
• /
• 2013

This study analyzed characteristics of 240 W high power LED lamps by comparing with those of traditional metal halide lamps. In addition, it analyzed the propriety of LED lamps as a source of light, considering seawater transmission characteristics. When Applying white LED package with the color temperature color temperature of 6500K, a 240W-LED fishing lamp has a characteristics of the luminous angle to be expanded to ${\pm}45^{\circ}$, the illumination change was improved to 0.8, as well as the luminance efficiency was improved to 98.8lm/W. As results of comparison between one 1,500W-metal halide lamp and four 240W-LED lamp with considering a seawater transmission and a luminous efficiency of scotopic vision, the radiant flux of two lamps were almost equal level at 50m depth and the luminous flux was 5% higher LED lamp than metal-halide lamp even if only applying the luminous efficiency of scotopic vision. As the luminous flux of LED lmap was 14% higher than that of metal-halide lamp with applying the luminous efficiency of scotopic vision to radiant flux at 50m depth, so LED fishing lamp was verified to alternative possibility of metal-halide lamp.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.35-36
• /
• 2014

본 논문은 Rear Combination LED Lamp 동작 시 전류와 광출력의 변동폭를 최소화하는 LED 조명광원의 특성을 고려하여 정전류 회로의 구현이 유리한 DC/DC 컨버터의 EMC 고효율 필터를 제안하여 외부의 전자계로부터 장애를 유발하지 않고, 일정 수준의 전자파 환경에서도 오동작 없이 원할하게 작동될 수 있도록 관련 기기 상호간의 전파 환경을 개선하는 고효율 Filter를 제안 하고자 한다. 본 논문에서 제안한 Filter는 EMI 측정을 통해 타당성과 우수성을 검증하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.299-299
• /
• 2014

기존의 고출력 광원들이 환경문제 등으로 외국에서 규제대상으로 지정되고 있는 가운데고체 상태의 광원인 Light-emitting diode (LED)는 기존의 광원에 비해 에너지 절감효과 크기 때문에 인해 널리 사용되고 있는 추세이다. 대부분의 백색 LED의 경우 청색 LED에 황색 형광체를 사용하는 것이 일반적이다. 그러나 이의 경우 빛의 흡수와 재방출 과정에서 생기는 에너지 변환손실의 문제가 불가피하다. 또한, 두 종류의 색을 섞어서 나타나는 낮은 연색성의 문제가 있고 사용할 수 있는 형광체의 종류와 조합도 일본 등 해외에 출원된 특허권으로 연구개발에 어려움이 있다. 이를 해결하기 위해 본 연구에서는 형광체를 사용하지 않는 단일 백색 LED를 개발을 위하여 극성과 반극성을 조합한 구조를 연구하였다. Photo-lithography를 이용하여 다양한 크기와 구조의 홀 패턴을 얻을 수 있었으며, metal organic chemical vapor deposition을 이용하여 다양한 형태의 피라미드 구조를 성장할 수 있었다. 패턴의 홀 크기와 홀 사이의 간격을 조절하면서 성장을 진행 하였고, 그 결과 pyramid와 truncated pyramid 모양의 GaN 구조를 성장할 수 있었다. [그림 1] Pyramid 구조의 반극성 면과 truncated pyramid 구조의 극성 면사이의 성장속도 차이 때문에 양자우물의 두께가 달라짐을 확인하였다. 이로 인해 양자구속효과가 달라져 다른 파장의 발광을 기대할 수 있었다. 뿐만 아니라 In의 확산거리가 Ga보다 길어서 홀사이 간격을 달리하면 In조성비가 달라지는 효과가 있음을 확인하였고 다양한 홀 사이 간격으로부터 각기 다른 파장의 발광을 얻을 수 있었다. 파장을 조금 더 상세하게 분석하기 위하여 Photoluminescence과 Cathodoluminescence을 사용하였다. 이로써 여러 파장을 발광하는 패턴을 섞어 넓은 영역의 발광 스펙트럼을 만들었다. 특히 패턴을 섞는 방법도 홀과 에피 구조를 섞는 방법, 크기가 다른 홀 패턴을 배열하는 방법등 다양히 하며 가장 좋을 패턴을 연구하였다. 그리하여 최적의 패턴과 구조, 성장조건을 찾아 백색의 CIE 좌표값을 얻을 수 있었다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.506-511
• /
• 2017

LED lighting, which many companies are pursuing commercialization, is a representative green energy technology. However, the LED lighting for broadcasting image should have high output and easy portability compared with general LED lighting devices for street lamps, advertisement or transportation devices. Therefore, while shooting a broadcast image if you use LEDs as a substitute light source for halogen lamps and fluorescent lamps that are large in size and uncomfortable to handle it is expected that the lightening of the equipment will activate the broadcasting image lighting equipment industry. After considering the mass production of the LED module board and the SMT production size of the chip mounter, the board size was determined considering the overall size of the product by model. In this paper, four 20W LED boards are arranged vertically in order to produce an 80W board. In other words, by sharing LED module board size by model, high power LED lighting equipments of 120W and 200W can be selected as an increase in the number of boards.