• Journal of the Korean Chemical Society
• /
• v.48 no.6
• /
• pp.561-567
• /
• 2004

The influence of ultrasound frequency, dissolved gases, and initial concentration on the decomposition of sodium dodecylbenzene sulfonate(DBS) aqueous solution was investigated using ultrasound generator with 200 W ultrasound power. The decomposition rates at three frequencies(50, 200, and 600 kHz) examined under argon atmosphere were highest at 200 kHz. The highest observed decomposition rate at 200 kHz occurred in the presence of oxygen followed by air and argon, helium, and nitrogen. The effect of initial concentration of DBS on the ultrasonic decomposition was decreased with increasing initial concentration and would depend upon the formation of micelle in aqueous solution. It appears that the ultrasound frequency, dissolved gases, and initial concentration play an important role on the sonolysis of DBS. Sonolysis of DBS mainly take place at the interfacial region of cavitation bubbles by both OH radical attack and pyrolysis to alkyl chain, aromatic ring, and headgroup.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.95-103
• /
• 2021

Sn-58Bi-xRu composite solders were prepared by adding Ru nanoparticles to Sn-58Bi, a typical low-temperature solder, and the interfacial reaction and solder joint reliability were analyzed by reacting with Cu/OSP and ENIG surface treated PCB boards. The Cu₆Sn₅ IMC formed by the reaction with Cu/OSP had little change in thickness depending on the Ru content, and ductile fracture occurred inside the solder during the high-speed shear test without any significant change even after 100 hr aging. In reaction with ENIG, the Ni₃Sn₄ IMC thickness tended to decrease as the Ru content increased, and ENIG-specific brittle fracture was found in some specimens. Since Ru element is not found near the interface, it is judged not to be significantly involved in the interfacial reaction, and it is analyzed that it mainly exists together with the Bi phase.

• Korean Journal of Materials Research
• /
• v.8 no.1
• /
• pp.33-37
• /
• 1998

Sn-Zn계 solder에서 Zn함량의 변화에 따른 납땜성을 납땜분위기 및 용제를 달리하여 연구하였다. 계면에서의 미세조직 관찰은 열처리온도를 8$0^{\circ}C$와 10$0^{\circ}C$로 달리하여 100일간 열처리한 후 관찰하였다. 젖음성 측정 결과, Zn함량이 증가함에 따라 젖음성은 감소하였고 RMA-용제를 사용한 경우가 R-용제를 사용한 경우에 비해 젖음성이 향상되었다. Sn-9Zn의 접촉각은 약 45도이고, 공기중에서 보다 질소 분위기에서 납땜한 경우가 젖음성 개선을 나타냈다. Sn-9Zn땝납과 Cu기판에서의 계면반응을 XRD, EDS로 분석한 결과 계면화합물은 r상(Cu$_{5}$Zn$_{3}$)으로 구성되어 있음을 알 수 있으며, 시효처리에 따라 접합부의 solder쪽에는 Zn상의 고갈이 나타남을 확인할 수 있었다.

• Journal of the Korean Ceramic Society
• /
• v.37 no.10
• /
• pp.994-1000
• /
• 2000

Mn-Ni-Co계 스피넬을 모재로 선택하여 상업용 페라이트 등 다양한 종류의 Fe-스피넬과 동시 소결 가능성을 검토할 목적으로 각 소재의 소결 거동, 서미스터와의 계면 반응이나, 2차상의 형성 등에 대해 알아보았다. 대부분의 페라이트 조성이 Mn 스피넬과 새로운 2차상을 형성하지는 않는 것을 알 수 있었다. 상업용 페라이트의 경우 115$0^{\circ}C$ 소결 온도에서 접합이 가능한 조성은 다량의 액상이 존재하며 접합계면의 폭이 상대적으로 넓으므로 서미스터 특성에도 좋지 않은 영향을 줄 수 있을 것으로 생각된다. 반면에 MFN1과 MFN2 조성은 접합계면에서 새로운 2차상이 형성되지 않고 원소의 상호확산도 작아 NTC 서미스터의 동시소결용 보호재로서의 가능성이 높은 것으로 확인되었다.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.220-224
• /
• 2014

Protein adsorption kinetics was studied with the amount of proteins adsorbed to contact lens hydrogels over time scales. Hydroxyethylmethacrylate (HEMA) and silicone hydrogels were dipped in protein solutions (albumin or IgG) and adsorption amounts were measured over time scales. The amount of protein adsorbed to both hydrogel types increased rapidly in 10 min, and remained consistently in 90 min. Decreasing interfacial energetics was taken slowly up to an hour in spite of rapid diffusion of protein molecules. This is due to the fact that water deprivation from three dimensional interphase initially formed by protein diffusion took over an hour. Interpretation of adsorption kinetics on contact lens hydrogels was discussed with understanding of relationship between surface energy and protein adsorption capacity.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.718-727
• /
• 2002

In this work, an Ar+ beam was irradiated on carbon fiber surfaces to improve the interfacial shear strength (IFSS) of the resulting composites using an ion assisted reaction (IAR) method h single fiber pull-out test was executed to investigate the basic characteristics of the single Carbon fiber/matrix interface. Based on Greszczuk's geometrical model, the debonding force for pull-out of the fiber from the resins was discussed with the applied ion beam energy as a result, it was known that an ion beam treatment produced the functional groups on fiber surface and etching lines along the fiber axis direction, resulting in increasing the adhesion forces between fibers and matrix, which caused the improvement of the IFSS in a composite system. And, it was also found that the maximum IFSS was shown at 0.8 keV ion beam energy in this system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.113-113
• /
• 2000

직접천이형 wide band gap(3.4eV) 반도체중의 하나인 GaN를 청색 및 자외선 laser diode, 고출력 전자장비 등으로 응용하기 위해서는 낮은 접합저항을 갖는 Ohmic contact이 선행되어야 한다. 그러나 만족할만한 p-type GaN의 Ohmic contact은 아직 실현되고 있지 못하며, 이는 GaN와 접합 금속과의 구체적인 반응의 연구를 필요로 한다. 본 연구에서 앞서 Pt, Pt, Ni등의 late transition metal을 p-GaN에 접합시킨 결과 이들은 접합 당시 비교적 평탄하나 후열 처리과정에서 비교적 낮은 온도에서 기판과 열팽창계수의 차이로 인하여 평탄성을 잃어버리면서 barrier height가 증가한다는 사실을 확인하였다. 따라서 본 연구에서는 이러한 열적 불안정성을 극복하기 위하여 Ni과 Pd를 차례로 증착하고 가열하면서 interfacial reaction, film morphology, Fermi level의 움직임을 monchromatic XPS(x-ray photoelectron spectroscopy) 와 SAM(scanning Auger microscopy) 그리고 ex-situ AFM을 이용하여 밝히고자 하였다. 특히 후열처리에 의한 계면 반응에 수반되는 구성 금속원소 간의 합금현상과 금속 층의 평탄성이 밀접한 관계가 있다는 것을 확인하였다. 이러한 합금과정에서 나타나는 금속원소들의 중심 준위의 이동을 체계적으로 규명하기 위해서 Pd1-xNix와 Pd1-xGax 합금들의 표준시료를 arc melting method로 만들어 농도에 따른 금속원소들의 중심 준위의 이동을 측정하여, Pd/Ni/p-GaN 및 Ni/Pd/p-GaN 계에서 열처리 온도에 따른 interfacial reaction을 확인하였다. 그 결과 두 계가 상온에서 nitride 및 alloy를 형성하지 않고 고르게 증착되고, 열처리 온도를 40$0^{\circ}C$에서 $650^{\circ}C$까지 증가시킴에 따라 계면반응의 부산물인 metallic Ga은 증가하고 있으마 nitride는 여전히 형성되지 않는 것을 확인하였다. 증착당시 Ni이 계면에 있는 Pd/Ni/p-GaN의 경우에는 52$0^{\circ}C$까지의 열처리에 의하여 Ni과 Pd가 골고루 섞이고 그 평탄성도 유지되고 barier height의 변화도 없었다. 더 높은 $650^{\circ}C$ 가열에 의해서는 surface free energy가 작은 Ga의 활발한 편석 현상으로 인해 표면은 Ga이 풍부한 Pd-Ga의 합금층으로 덮이고, 동시에 작은 pinhole들이 발생하며 barrier height도 0.3eV 가량 증가하게 된다. 반면에 증착당시 Pd이 계면에 있는 Ni/Pd/p-GaN의 경우에는 40$0^{\circ}C$의 가열까지는 두 금속이 그들 계면에서부터 섞이나, 52$0^{\circ}C$의 가열에 의해 이미 barrier height가 0.2eV 가량 증가하기 시작하였다. 더 높은 $650^{\circ}C$가열에 의해서는 커다란 pinhole, 0.5eV 가량의 barrier height 증가, Pd clustering이 동시에 관찰되었다. 따라서 Ni과 Pd의 일함수는 물론 thermal expansion coefficient가 거의 같으며 surface free energy도 거의 일치한다는 점을 감안하면, 이렇게 뚜렷한 열적 안정성의 차이는 GaN와 contact metal과의 반응시작 온도(disruption onset temperature)의 차이에 기인함을 알 수 있었다. 즉 계면에서의 반응에 의해 편석되는 Ga에 의해 박막의 strain이 이완되면, pinhole 등의 박막결함이 줄어 들고, 이는 계면의 N의 out-diffusion을 방지하여 p-type GaN의 barrier height 증가를 막게 된다.

• Applied Chemistry for Engineering
• /
• v.30 no.2
• /
• pp.241-246
• /
• 2019

In this paper, reactive surfactants were synthesized by using acrylic acid or 3-butenoic acid as nonionic surfactants, polyoxyethylene(23) lauryl ether (Brij 35) and polyoxyethylene(20) stearyl ether (Brij S20). The synthesis of surfactants was confirmed by FT-IR and $^1H$-NMR. The surface tension, emulsifying property, and foam power and stability were also measured. The surface tension value was 35~41 dyne/cm at an critical micelle concentration (cmc) which was measured as $1.0{\times}10^{-4}{\sim}9.7{\times}10^{-5}mol/L$ using a surface tension method. The emulsifying power of synthesized surfactant was measured with benzene, soybean oil and monomer. Also, the initial height of the bubbles and the height after 5 minutes were measured and the values were compared with each other.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.172-177
• /
• 1999

Graphite and carbonaceous materials showed an excellent capability as a negative electrode in Li-ion batteries because Li-ion can be intercalated and de-intercalated reversibly within most carbonaceous materials of layered structure. Also, the electrochemical potential of Li-intercalated carbon anode is almost identical with that of Li metal. In the present study, mesocarbon microbeads(MCMB) were used as anode electrode and its properties of charge/discharge and interfacial reaction with electrolyte were studied by Potentiostat/Galvanostat test, FT-IR analysis, XRD and SEM. The passivation film of solid-state was formed as the interface between electrode and electrolyte as the cell reaction began and, once formed, became thicker with repeated charge/discharge process. Also, the relationship between the passivation film formed at the electrode interface and storage capacity was discussed.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.51-57
• /
• 2016

In this study, we synthesized reactive surfactant which have functional radical group for effective chemical reaction. Reactive surfactant have been synthesized using synthesis of polyoxyethylene lauryl ether(POE 23) which is nonionic surfactant and methacrylic acid, acrylic acid. benzene was used as the solvent, p-TsOH was used as the catalyst. synthesized surfactant was confirmed by FT-IR, $^1H$-NMR spectra, and elemental analysis. Evaluation of physical properties was measured HLB, cloud point, surface tension, the critical micelle concentration, emulsifying power. HLB number was evaluated 11.62 to 12.09 range. The Critical Micelle Concentration(cmc) values evaluated was $1{\times}10^{-4}{\sim}5{\times}10^{-4}mol/L$ by surface tension method. The cloud point was $35^{\circ}C$, $39^{\circ}C$ each. The emulsifymvcqa ing properties of the synthesized surfactants was lower than polyoxyethylene lauryl ether. In addition, soybean oil was better than benzene. The experimental results confirmed the ester bond, the yield of 93.27%, 94.49% was found.