• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.297-302
• /
• 1998

유한요소법을 이용하여 스프링으로 연속 지지되고 축방향 하중이 작용하는 핵연료봉의 자유진동 해석올 수행하였다. 본 해석에는 지지격자 지지점에서 핵연료봉의 변위가 구속되지 않는 실제 경계조건을 반영하였다. 이러한 경계조건은 지지점 스프링 상수에 의하여 핵연료봉 해석모델의 탄성항이 약화되는 현상을 반영할 수 있어서 지지점이 구속된 기존의 모델보다 고유진동수를 작게 예측한다. 스프링 상수가 어떤 임계값 이하를 갖는 경우 고유진동수 뿐만 아니라 모드형상도 크게 변하기 때문에 지지점을 구속한 모델에 의한 해석은 실제 진동현상을 상당히 왜곡 할 수 있다. 핵연료봉에 작용하는 축방향력이 인장력에서 압축력으로 감소함에 따라 고유진동수도 감소하지만 핵연료봉의 고유형상은 변하지 않았다. 지지격자 스프링 상수의 점진적인 감소와 핵연료봉 축방향 압축력의 감소를 동시에 적용하는 경우 고유 진동수는 두 변수를 별도로 적용했을 때 얻은 최소값의 변화에 따르는 경향을 나타내었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.61-68
• /
• 1991

The system such as railway bridge can be modelled as the restrained beam with intermediate supports. This kind of structures are subject to the moving load, which has a great effect on dynamic stresses and can cause sever motions, especially at high velocities. Therefore, to analyze the dynamic characteristics of the system due to the moving load is very important. In this paper, the governing equation of motion of a restrained beam subjected to the moving load is derived by using the Hamilton's principle. The orthogonal polynomial functions, which are trial functions and satisfying the geometric and dynamic boundary conditions, are obtained through simple procedure. The dynamic response of the system subjected to the moving loads is obtained by using the Galerkin's method and the numerical time integration technique. The numerical tests for various constraint, velocity and boundary conditions were preformed. Furthermore, the effects of mass of the moving load are studied in detail.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.3
• /
• pp.11-21
• /
• 2008

A linear and non-linear analysis for plates and shells with arbitrary edge supports subjected to various loading was presented. The 9-node ANS(Assumed Natural Strain) hell element was employed and the spring element, which could express an arbitrary edge support using the six degrees of freedom, was introduced. For the application of his analysis, the plates and shells with various edge supports were analyzed, and the ending behavior with these edge supports were obtained accurately. For these edge supports, particularly elastic edge support was simulated by six springs and reasonable results were obtained. The results show that the present method can be widely used to analyze the bending behavior of plates and shells with arbitrary edge conditions.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.562-565
• /
• 2010

본 논문에서는 유한요소법을 이용하여 두 개의 층으로 이루어진 Si/SiGe 나노스프링의 기하학적 형상에 대한 연구가 수행된다. 나노스프링의 기하학적 형상에 영향을 미치는 주 설계요소로는 두께, 폭, 길이, 격자방향 등이 있으며, 두 개의 층으로 이루어진 Si/SiGe 박막이 나노스프링의 형상을 가지게 되는 주원인으로는 두 개의 층 경계면에서 발생하는 misfit strain이 있다. 본 연구에서는 두께, 폭, 길이, 격자방향 등의 설계요소를 변화시켜가면서 mistif strain에 의한 나노스프링의 곡률 변화에 대한 해석 결과가 제시된다. 또한 해석 결과의 검증을 위해 해석해의 결과와 분자동력학 전산모사 결과가 함께 제시된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.396-401
• /
• 2019

A virtual rigid is modeled as the parallel structure of a virtual spring and a virtual damper. The reflective force from the virtual model is designed to be as large as possible to improve the realism of the virtual environment while maintaining the stable interaction. So, it is important to analyze the stability boundary of the virtual spring and damper. In the previous researches, the stability boundary is analyzed based on the zero-order-hold (ZOH) method, but it is analyzed based on the first-order-hold (FOH) method and the virtual damper in the paper. The boundary value of the stable virtual damper is inverse proportional to the sampling time and the maximum value of stable virtual stiffness is inverse proportional to the square of the sampling time. And the maximum value in the FOH method is increased to 110% of the value in the ZOH method. If the virtual damper is smaller than about 50% of the boundary value of the virtual damper in the FOH method, the stable virtual stiffness in the FOH method is several times larger than that in the ZOH method.

• Proceedings of the KAIS Fall Conference
• /
• 2006.11a
• /
• pp.83-86
• /
• 2006

본 논문에서는 수직형 스프링식 로프 브레이크에 관한 것으로 3차원 유한요소해석 코드인 ANSYS를 활용한 구조해석 결과를 기초 데이터로 사용하였으며, 내부응력, 경계조건, 하중등이 고려되었다. 또한 24인승 엘리베이터에 장착되는 로프 브레이크를 대상으로 해석하였다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.4
• /
• pp.45-54
• /
• 2011

A simple model for reinforced concrete shear walls with boundary elements is proposed, which is a macro-model composed of spring elements representing flexure and shear behaviors. The flexural behaviour is represented by vertical springs at the wall ends, where the moment strength and rotational capacity of the wall are based on section analysis. The shear behaviour is represented by a horizontal spring at the wall center, where the key parameters for the shear behavior are based on the flexural behaviour since the shear walls with boundary elements are governed by the flexure. The proposed model was prepared with the results of hysteretic tests of the shear walls, and then the reliability of the hysteretic rule and variables was investigated by nonlinear dynamic analyses. Using parametric study with nonlinear dynamic analyses, the effect of the variables on demand and capacity, which are major parameters in seismic performance evaluation, are investigated. Results show that the measured and calculated shear forces versus the shear distortion relationships are slightly different, but the global response is well simulated. Furthermore, the demand and capacity are also changed in a similar way to the change in the major parameters so that the proposed model may be appropriate for reinforced concrete shear walls with boundary elements.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.2
• /
• pp.137-145
• /
• 2004

The paper provides a methodology of identifying a substructure model when sectional and material properties of the structure are not the a priori information. In defining a substructure model, it is required that structural responses be consistent with the actual behavior of the part of the structure. Substructure model is identified by estimating boundary spring constants and stiffness properties of the substructure. Static and modal system identification methods have been applied using responses measured at limited locations within the substructure. Simulation studies for static and dynamic responses have been carried. The results and associated problems are discussed in the paper. The procedure has been also applied to an actual multi-span plate-girder Gerber-type bridge with dynamic responses obtained from a moving truck test and construction blasting vibrations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.76-82
• /
• 2018

In this present study, in order to update the finite element model considering the boundary conditions, a method has been proposed. The conventional finite element model updating method, updates the finite element model by using the dynamic characteristics (natural frequency, mode shape) which can be estimated from the ambient vibration test. Therefore, prediction of the static response of an actual structure is difficult. Furthermore, accurate estimation of the physical properties is relatively hard. A novel method has been proposed to overcome the limitations of conventional method. Initially, the proposed method estimates the rotational spring constant of a finite element model using the deflection of structure and the rotational displacement of support measurements. The final updated finite element model is constructed by estimating the material properties of the structure using the finite element model with updated rotational spring constant and the dynamic characteristics of the structure. The proposed finite element model updating method is validated through numerical simulation and compared with the conventional finite element model updating method.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.4
• /
• pp.27-38
• /
• 2001

A mechanical lumped parameter model is proposed for the dynamic modeling of a semi-infinite reservoir. A semi-analytic transmitting boundary is derived for a semi-infinite 2-D reservoir of constant depth. The characteristics of the solution are examined in both frequency and time domains. Mass, damping and spring coefficients of the mechanical model are obtained to preserve the major features of the solution such as eigenfrequencies and the shapes of Bessel functions that appear as kernels in the convolution integrals. The lumped parameter model in its final form consists of two masses, a spring and two dampers for each eigenfrequency. Application examples demonstrated that the new lumped parameter model could be used for the time domain analysis of dam-reservoir systems.