• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.490-492
• /
• 2010

A swing level controlled voltage-mode transmitter is proposed to support a stub series-terminated logic channel with center-tapped termination. This transmitter provides a swing level control to support the diagnostic mode and improve the signal integrity in the absence of the destination termination. By using the variable parallel termination, the proposed transmitter maintains the constant output impedance of the source termination while the swing level is controlled. Also, the series termination using an external resistor is used to reduce the impedance mismatch effect due to the parasitic components of the capacitor and inductor. To verify the proposed transmitter, the voltage-mode driver, which provides eight swing levels with the constant output impedance of about $50{\Omega}$, was implemented using a 70nm 1-poly 3-metal DRAM process with a 1.5V supply. The jitter reduction of 54% was measured with the swing level controlled voltage-mode driver in the absence of the destination termination at 1.6-Gb/s.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.16-21
• /
• 2007

CMOS variable gain amplifier (VGA) IC designs for the structure monitoring systems of the telemetries were developed. A three stage cascaded VGA using a differential amplifier and a linear-in-dB controller is presented. A proposed VGA is a modified version of a conventional VGA such that the gain is controlled in a linear-in-dB fashion through the current ratio. The proposed VGA circuit introduced in this paper has a dynamic range of 77 dB with 1.5 dB gain steps. It also achieved a gain error of less than 1.5 dB over 77 dB gain range. The VGA can operate up to 10MHz dissipating 13.8 mW from a single 1.8 V supply. The core area of the VGA fabricated in a Magnachip $0.18{\mu}m$ standard CMOS process was about $430{\mu}m{\times}350{\mu}m$. According to measurement results, we can verify that the proposed method is reasonable with regard to the enhancement of dynamic range and the better linear-in-dB characteristics.

• 전자공학회논문지 IE
• /
• v.47 no.4
• /
• pp.1-9
• /
• 2010

This paper describes a ultrasonic signal processing front-end IC for distance range meter and body detector. The burst shaped ultrasonic signal is generated by a self oscillator and its frequency range is about 40[kHz]-300[kHz]. The generated ultrasonic signal transmit through piezo resonator. The another piezo device transduce from received ultrasonic signal to electrical signals. This front-end IC contained low noise amplifier, band pass filter, busrt detector and time pulse generator and so on. This IC has two type of new idea for improve function and performance, which are self frequency control (SFC) and Variable Gain Control amplifier (VGC) scheme. The dimensions and number of external parts are minimized in order to get a smaller hardware size. This device has been fabricated in a O.6[um] double poly, double metal 40[V] High Voltage CMOS process.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.81-83
• /
• 2009

가정용 연료전지의 상용화를 위해서는 시스템의 신뢰성과 경제성 향상이 중요한 문제이며, 경제성 향상은 시스템의 가격 절감과 컨버터의 효율 향상을 통해서 달성될 수 있다. 본 논문은 1kW급 가정용 연료전지 시스템을 위한 새로운 고효율 푸쉬풀 컨버터의 토폴로지를 제안한다. 제안된 컨버터는 2차측을 낮은 정격 전압을 가진 정류 다이오드를 사용한 2단 정류구조로 구성하여 다이오드의 손실을 저감시키고, 다이오드의 접합 커패시턴스와 변압기의 누설 인덕턴스의 상호작용에 의해 발생하는 공진 전압의 크기를 저감시킴으로써 스너버에서 소모되는 전력을 줄여 효율을 향상시켰다. 실험에서는 일반적인 형태의 푸쉬풀 컨버터 1차측 회로와 고주파 변압기는 공유하고, 2차측회로만 변경하는 방법으로 효율을 측정하여 비교함으로써 제안된 방식의 우수함을 증명하였다. 제안된 방식의 푸쉬풀 컨버터는 기존방식에 비해 특히 경부하에서 높은 효율을 나타내었으며, 전 부하 구간에서 효율의 변화가 크지 않아 부하가변 방식의 운전에 유용하게 사용될 수 있을 것으로 판단된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.123.2-123.2
• /
• 2011

$ALU^+$ 태양전지는 PN접합을 후면에서 즉, Al을 소성하여 형성시키기 때문에 얼마나 균일하고 두껍게 형성하는 것이 가장 중요하다. 소성(Firing)은 태양전지 제조 과정에서 후면의 접촉을 위한 중요한 공정이다. 본 연구에서는 상업화가 가능한 n-type $ALU^+$ Emitter 태양전지에서 소성 횟수에 따른 특성을 연구 하였다. $ALU^+$ emitter 형성의 최적화를 위해 소성온도를 가변하고, 최적화된 온도에서 소성 횟수에 따른 DIV 측정을 통해 셀을 분석 하였다. 소성 횟수는 1~3회로 하였고, 그 결과 단락전류 밀도(Jsc)가 33.57mA/$cm^2$로 처음보다 15.1%증가 하였고, 곡선인자(Fill Factor)는 3회에서 66.04%로 218%증가 하였다. Al을 짧은 시간 안에 소성을 시키므로 해서 후면의 $P^+$ Emitter가 균일하게 형성되었기 때문에 개방전압(Voc)의 증가를 확인하였다. 본 연구를 통해 $ALU^+$ 태양전지의 후면 Aluminium 소성 조건의 최적화를 통하여 $ALU^+$ emitter가 충분히 형성되지 못하면 누설전류가 발생되고 직렬저항(Rs)이 크게 증가하여 개방전압(Voc) 및 단락전류밀도(Jsc)의 감소가 발생하게 되고, 직렬저항(Rs)의 증가와 병렬저항(Rsh)의 감소는 Fill Factor의 급격한 감소를 초래하게 됨을 알 수 있다. 이를 개선하면 태양전지 효율을 상승시키는 결과를 얻을 수 있음을 확인하였다.

• Journal of IKEEE
• /
• v.15 no.3
• /
• pp.205-210
• /
• 2011

A novel hysteresis tunable monolithic comparator circuit based on a 0.35 ${\mu}m$ CMOS process is suggested in this paper. To tune the threshold voltage of the hysteresis in the comparator circuit, two external digital bits are used with supply voltage of 3.3V. The threshold voltage of the suggested comparator circuit is controlled by 234mV by change of 4 digital control bits in the simulation, which is a close agreement to the analytic calculation.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.695-703
• /
• 2019

In this paper, we propose a method to remove the circulating current which can occur in the parallel connection of the high voltage series connected battery module in the battery pack. The removal way is a method of inserting a module named VVSM (Variable Voltage Variable Module) using bidirectional DCDC converter and supercapacitor in place of one or some of the cascaded battery cells in the battery pack configuration. In this module, it operates like a battery cell that can be controlled at a desired voltage. VVSM is used to match the voltages of the cascaded battery modules very easily. To demonstrate the proposed method, a PSIM simulation for battery model is used. In addition, the module with only the battery cell connected in series and the module with the proposed VVSM are made, and the two modules were connected in parallel to measure the circulating current between the two modules. As a result, it was verified that the proposed method effectively suppressed the circulating current.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.299-302
• /
• 2016

In this paper, we designed the stack monitoring system with improved performance. To block the incoming pulse noise to the amplifier, shield and the power supply impedance are reduced and the power circuit is isolated. The control unit is developed with variable high voltage, adaptive gain, offset and threshold in order to match the scintillation detector characteristic to the apparatus. 300-1500V variable high voltage power circuit is configured applicable to various scintillation detector. Stack monitoring system with improved performance guarantee the efficiency and the reliability by considering the characteristic of various scintillation detector. Developed stack monitoring system is evaluated with certified testing equipment and shows excellent performance with respect to the uncertainty of the sensor test results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.100-108
• /
• 2008

The transient ground impedance depending on configuration, size, and material of grounding electrodes as well as the shapes of impulse currents, has a significant affect on the performance of the grounding system. This paper presents experimental results in regard to the analysis method of transient ground impedance using the lightning impulse and variable frequency currents. Also a new estimation method to replace the effective surge impedance for transient ground impedance was proposed. The ground electrodes used in this experiment are virtual ground electrodes including both resistance and inductance components, carbon ground electrode with 1[m] length, copper electrode with 9[m] length and counterpoise with 40[m] length. Ground impedances using the proposed method were measured respectively. Comparing with the ground impedance using variable frequency current the conventional ground impedance($Z_1$) calculated from the peak values of impulse voltage and impulse current is observed more correct method for evaluating the performance of ground electrode than the effective surge impedance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.10A
• /
• pp.1223-1229
• /
• 2004

A variable-gain low-voltage low noise amplifier MMIC operating at 5GHz frequency band is designed and implemented using the ETRI 0.5$\mu\textrm{m}$ GaAs MESFET library process. This low noise amplifier is designed to have the variable gain for adaptive antenna array combined in HIPERLAN/2. The feedback circuit of a resistor and channel resistance controlled by the gate voltage of enhancement MESFET is proposed for the variable-gain low noise amplifier consisted of cascaded two stages. The fabricated variable gain amplifier exhibits 5.5GHz center frequency, 14.7dB small signal gain, 10.6dB input return loss, 10.7dB output return loss, 14.4dB variable gain, and 2.98dB noise figure at V$\_$DD/=1.5V, V$\_$GGl/=0.4V, and V$\_$GG2/=0.5V. This low noise amplifier also shows-19.7dBm input PldB, -10dBm IIP3, 52.6dB SFDR, and 9.5mW power consumption.